BISSELL CrossWave™ User Guide

Getting Started

The BISSELL CrossWave™ is designed to vacuum and wash your floors simultaneously. Please refer to the following steps for assembly and initial use.

Included Components:

• Main unit
• Handle assembly
• Cleaning formula
• Water tank
• Brush roll
• Storage tray

Assembly:

1. Attach the handle assembly to the main unit. [arrow-right]
2. Insert the clean water tank. [arrow-right]
3. Fill the clean water tank with water and BISSELL cleaning formula as per instructions for large or small areas. [water-drop-symbol] [bottle-symbol]
4. Ensure the brush roll is properly installed. [brush-symbol]
5. Place the unit on the storage tray when not in use. [tray-symbol]

For detailed assembly, please see the diagrams provided in the original document.

Operation

Before Cleaning:

• Ensure the unit is plugged into a power outlet. [plug-symbol]
• Fill the clean water tank and the formula tank as needed.

Cleaning Steps:

1. Turn on the unit. [power-symbol]
2. Select the appropriate cleaning mode (e.g., hard floors, area rugs).
3. Move the unit back and forth over the soiled area. The unit will spray cleaning solution and vacuum up the dirty water.
4. For stubborn stains, you may need to make multiple passes.
5. After cleaning, turn off the unit and unplug it. [power-symbol] [unplug-symbol]

Important Safety Information:

• Always unplug the unit before performing any maintenance. [unplug-symbol]
• Do not use on wet surfaces or in areas with standing water.
• Keep out of reach of children. [child-symbol]
• Refer to the safety warnings [warning-symbol] and operating instructions [book-symbol] in the original document for complete safety details.

Maintenance

Regular maintenance ensures the longevity and performance of your BISSELL CrossWave™.

Emptying the Dirty Water Tank:

1. Turn off and unplug the unit. [power-symbol] [unplug-symbol]
2. Remove the dirty water tank. [tank-removal-symbol]
3. Empty the contents into a toilet or sink.
4. Rinse the tank with clean water.
5. Reinstall the dirty water tank.

Cleaning the Brush Roll:

1. Turn off and unplug the unit. [power-symbol] [unplug-symbol]
2. Remove the brush roll cover. [cover-removal-symbol]
3. Carefully remove the brush roll. [brush-removal-symbol]
4. Rinse the brush roll under running water. [water-symbol]
5. Allow the brush roll to air dry completely before reinstalling. [sun-symbol]
6. Reinstall the brush roll and cover.

Cleaning the Filters:

1. Turn off and unplug the unit. [power-symbol] [unplug-symbol]
2. Locate and remove the filter(s). [filter-removal-symbol]
3. Rinse the filter(s) with clean water. [water-symbol]
4. Allow the filter(s) to air dry completely before reinstalling. [sun-symbol]

Cleaning the Nozzle and Foot:

1. Turn off and unplug the unit. [power-symbol] [unplug-symbol]
2. Wipe the nozzle and foot with a damp cloth. [cloth-symbol]

Storage:

Store the unit in a cool, dry place, preferably on its storage tray. Ensure all parts are dry before storage.

Troubleshooting

If you encounter issues, please refer to the following common solutions:

• Unit not turning on: Ensure the unit is properly plugged in. [plug-symbol]
• No spray: Check if the clean water tank is filled and properly seated. Ensure the spray trigger is being pressed. [water-drop-symbol]
• Poor suction: Empty the dirty water tank. Clean or replace the filters. Check for blockages in the nozzle or hose. [blockage-symbol]
• Brush roll not spinning: Ensure the brush roll is correctly installed and not tangled with debris. [brush-symbol]
• Unit leaking: Ensure the dirty water tank and clean water tank are properly seated. Check for damage to the tanks or seals. [leak-symbol]

For further assistance, please visit BISSELL.com/videos or contact BISSELL customer support.