Instruction Manual for ESCALADE models including: B5455 Ball Holder, B5455, Ball Holder
INSTALLATION INSTRUCTIONS MODEL NO. B A L L H O L D E R B5455 PRE-ASSEMBLY TIPS 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Do not tighten until instructed to do so. If parts are tightened too soon, parts may not easily fit together. 3. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for replacement parts. TOOLS NEEDED FOR ASSEMBLY: Phillips Screw driver Cordless Drill 5/6" Socket driver bit PARTS LIST (NOT ACTUAL SIZE) 2 1 BASE 3M-9137-00 QTY. 1 GRIPPER FINGER 3M-9138-00 QTY. 4 3 Please Do Not Return This Product To The Store! Contact Escalade® Sports customer service department at: Phone: 1-800-USA-GOAL Toll Free ! Fax: 1-866-873-3536 Toll Free ! E-mail: basketball@escaladesports.com Escalade Sports Physical Location: 817 Maxwell Ave. Evansville, IN 47711 Mailing Address: (Correspondence Only) PO Box 889 Evansville, IN 47706 HARDWARE NEEDED (ACTUAL SIZE) 4 5 #8 X .375 Phillips Head Trilobular Screw 1B-7225-00 QTY. 10 6 #10 X 1.0 Phillips screw 1B-7226-00 QTY. 1 7 MOUNTING BRACKET 3M-9139-00 (QTY. 1) TAPE PATCH 1M-6289-00 QTY. 1 #10 X 1.125 Self Drilling Screw 1B-6821-00 QTY. 1 Escalade® Sports products may be manufactured and/or licensed under the following patents. 6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431 Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. 2L-7952-00 2021 Escalade Sports 1. Assemble four Gripper Fingers (#2) to Base (#1) as shown in Figure 1 & Back View. 2 FIGURE 1 4 1 TOOL NEEDED Phillips HARDWARE NEEDED 4 #8 X .375 Phillips Head Trilobular Screw 1B-7225-00 QTY. 8 BACK VIEW NOTE: Prepare hardware and tools below to be used for page 3 assembly steps. HARDWARE NEEDED TOOLS REQUIRED 4 7 #8 X .375 Phillips Head Trilobular Screw 1B-7225-00 QTY. 2 #10 X 1.125 Self Drilling Screw 1B-6821-00 QTY. 1 Cordless Drill 5/6" Socket driver bit 2 Phillips If installing to the back of a basketball pole continue onto Step 2 on this page. If mounting to a Wall skip this page and continue on page 4. 2. Clean the flat side of the mounting bracket surface with alcohol. Peel one side of the mounting Tape (#6) and adhere the to the Flat part of the Mounting Bracket (#2)as shown in Detail A. 3. Clean mounting location surface with alcohol. Peel the other side of the mounting tape and adhere mounting location. See Detail B. NOTE: Holes in the Mounting Bracket (#3) must be in the Vertical position as shown in Detail B before adhering Mounting Bracket to the pole. 4. Install self-drilling screw using 5/16" Hex Socket Driver and cordless drill. When 5/16" Hex Driver makes contact with Mounting Bracket finish tightening screw with Philips Screwdriver. Do not over tighten. See Detail C. 5. If self-drilling screw is not used Mounting Bracket must be clamped in place for 24 hours before attaching Ball Holder. 6. When the Mounting Bracket is completely adhered to the pole, attach the Ball holder assembly with two Screws (#4). See Figure 2. 3 FIGURE 2 NOTE: Tighten 4 until secure, but DO NOT OVERTIGHTEN. 3 3 DETAIL A Flat Surface Peel 6 Back of pole DETAIL B NOTE: Holes must be in the Vertical position as shown before adhering to pole. 3 DETAIL C 7 If installing to the back of a basketball pole go back to Step 2 on page 3. If mounting to a Wall continue on this page. NOTE: If you are mounting the Ball holder to a wall you will need to purchase either a drywall or masonry wall mounting kit depending on the wall you have. The kit will need an anchor for a #10 phillips head screw. 2. Follow the manufacturer's instructions on installing the anchor and then proceed to step 3. HARDWARE NEEDED 4 5 #8 X .375 Phillips Head Trilobular Screw 1B-7225-00 QTY. 2 TOOL NEEDED #10 X 1.0 Phillips screw 1B-7226-00 QTY. 1 3. Attach Mounting Bracket (#3) to the wall using Screw (#5) as shown in Detail A. The flat surface of the bracket must be facing the wall. NOTE: Holes in the Mounting Bracket (#3) must be in the Vertical position as shown in Detail A before attaching Mounting Bracket to the wall. 4. Attach the Ball holder assembly to the Mounting Bracket with two Screws (#4). See Figure 3. Phillips 3 DETAIL A Flat Surface 3 NOTE: Holes must be in the Anchor Vertical position as shown before screwing to wall anchor. FIGURE 3 4 NOTE: Tighten until secure, but DO NOT OVERTIGHTEN. 5 4Corel PDF Engine Version 19.1.0.419 CorelDRAW 2017