Installation Guide for luminii models including: LETO 44 Mini P, 954 Semi-Recessed Canopy, LETO 44 Mini P 954 Semi-Recessed Canopy, Semi-Recessed Canopy, Recessed Canopy, Canopy
Leto 44 Mini P UD – Luminii
Leto 44 Mini P – Luminii
LETO 44 Mini P 954 SEMI-RECESSED CANOPY Overview / Vue d'ensemble Feed Suspended AC P2 / DC P3 Powered Aircraft AC P4 / DC P5 For powered aircraft height adjustment, see P6 Read and follow these instructions before installing or maintaining this product · This product is suitable for DRY INDOOR LOCATIONS ONLY · Make sure this product is NOT on the same circuit as inductive loads, (e.g. fluorescent bulbs, discharge bulbs, ventilation fans, etc...) · Do not switch on line voltage until all wiring is complete · Incorrect wiring will result in irreparable damage to LED and power supply · This product should only be installed by a licensed electrician Veuillez lire et suivre ces instructions avant l'installation ou l'entretien de ce produit · Ce produit convient pour une installation DANS UN ENDROIT SEC SEULEMENT · Assurer vous que des charges inductives ne se retrouvent pas sur le même circuit que ce produit, (i.e. fluorescent, ampoules à décharge, ventilateurs, etc...) · Compléter les branchements avant de mettre sous tension · Un branchement incorrect créerait des dommages irréparables à l'alimentation et au DEL · Ce produit devrait être uniquement installé par un électricien qualifié Warranty · This product must be installed in accordance with all applicable installation codes and ordinance · Limited five (5) years warranty · Warranty is void in the eventuality of unauthorized modifications and/or improper use Garantie · Ce produit doit être installé conformément au code d'installation et autres normes applicables · Garantie limitée de cinq (5) ans · La garantie est non valide advenant une modification non autorisée ou un usage non approprié 1 Rev July 26, 2021 PROUD MEMBER OF MADE IN CANADA 403-216-7043 | info@sensolighting.com LETO 44 Mini P Pendant: Single Feed Cable (AC Connection) 1 Finish ceiling installation. Make sure hole is cut to appropriate size and location. 54mm (2.125") 2 Disassemble driver housing to expose the driver. 3 Make electrical connections and use appropriate strain relief. 9-25mm 4 Reassemble housing and insert into ceiling. Push aside to leave room for canopy. 5 Connect dimming controls to included cable clamps. Insert wires and canopy into ceiling. 6 Turn screws until housing is secured in place (arms will rotate and clamp down on ceiling) 7 Unscrew gripper plate and separate from canopy. 8 Loosen set screw and adjust cable to desired height. Cut and reconnect wire if needed. 9 Re-attach gripper to canopy and slide trim plate up until held in place by magnets. 2 Rev July 26, 2021 PROUD MEMBER OF MADE IN CANADA 403-216-7043 | info@sensolighting.com LETO 44 Mini P Pendant: Single Feed Cable (Remote DC Connection) 1 Finish ceiling installation. Make sure hole is cut to appropriate size and location. 54mm (2.125") 2 Disassemble driver housing to expose fixture wiring. Cylinder housing is used as DC junction box. 3 Make electrical connections and use appropriate strain relief. 9-25mm 4 Reassemble housing and insert into ceiling. Push aside to leave room for canopy. 5 Insert canopy into ceiling. 6 Turn screws until housing is secured in place (arms will extend and clamp down on ceiling) 7 Unscrew gripper plate and separate from canopy. 8 Loosen set screw and adjust cable to desired height. Cut and reconnect wire if needed. 9 Re-attach gripper to canopy and slide trim plate up until held in place by magnets. 3 Rev July 26, 2021 PROUD MEMBER OF MADE IN CANADA 403-216-7043 | info@sensolighting.com LETO 44 Mini P Pendant: Powered Aircraft Cable (AC Connection) 1 Finish ceiling installation. Make sure hole is cut to appropriate size and location. 54mm (2.125") 2 Disassemble driver housing to expose the driver. 3 Make electrical connections and use appropriate strain relief. 9-25mm 4 Reassemble housing and insert into ceiling. Push aside to leave room for canopy. 5 Connect dimming controls to included cable clamps. Insert wires and canopy into ceiling. 6 Turn screws until housing is secured in place (arms will extend and clamp down on ceiling) 7 Slide trim plate up until held in place by magnets. 4 Rev July 26, 2021 PROUD MEMBER OF MADE IN CANADA 403-216-7043 | info@sensolighting.com LETO 44 Mini P Pendant: Powered Aircraft Cable (Remote DC Connection) 1 Finish ceiling installation. Make sure hole is cut to appropriate size and location. 54mm (2.125") 2 Disassemble driver housing to expose fixture wiring. Cylinder housing is used as DC junction box. 3 Make electrical connections and use appropriate strain relief. 9-25mm 4 Reassemble housing and insert into ceiling. Push aside to leave room for canopy. 5 Insert canopy into ceiling. 6 Turn screws until housing is secured in place (arms will extend and clamp down on ceiling) 7 Slide trim plate up until held in place by magnets. 5 Rev July 26, 2021 PROUD MEMBER OF MADE IN CANADA 403-216-7043 | info@sensolighting.com LETO 44 Mini P Height Adjustment: Powered Aircraft Cable 1 Remove trim plate from the canopy 2 Unscrew gripper plate separate from canopy. 3 Loosen set screw and adjust cable to desired height. 4 Cut excess cable leaving ~3" above gripper. Make electrical connections using appropriate hardware. 5 If cables develop a twist, loosen set screw and cycle cable through the gripper 4-5 times. 6 Tighten screws, re-attach gripper plate to canopy and slide trim plate up until held in place by magnets. 6 Rev July 26, 2021 PROUD MEMBER OF MADE IN CANADA 403-216-7043 | info@sensolighting.comAdobe PDF Library 15.0 Adobe InDesign 16.3 (Macintosh)