Instruction Manual for i Safe MOBILE models including: IS-MP.1, Handheld Reader, IS-MP.1 Handheld Reader
8 4 USB PORT: HID (Human Interface Device) and to charge the battery. Do not open the USB port in hazardous areas! POWERING ON AND OFF THE IS-MP.1 To powering ON the device, press the [On/Off Key]. The screen lights up and the device is in running order.
Datenblätter, Zertifikate, Flyer und Manuals – i.safe MOBILE
File Info : application/pdf, 20 Pages, 606.76KB
DocumentDocumentQUICK START MANUAL SAFETY INSTRUCTIONS IS-MP.1 KEYS AND SPECIAL FEATURES 4 3 Display 2 1 Document No. 1020DI01REV01 Version: 2021-12-07 (c) 2017 i.safe MOBILE GmbH i.safe MOBILE GmbH i_Park Tauberfranken 10 97922 Lauda-Koenigshofen Germany Tel. +49 9343/60148-0 info@isafe-mobile.com www.isafe-mobile.com Template: TEMPMD01REV00 CONTENTS English. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Deutsch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 ENGLISH INTRODUCTION This document contains information and safety regulations which are to be observed without fail for safe operation of the device IS-MP.1 under the described conditions. Non-observance of this information and instructions can have serious consequences and/or may violate regulations. Please read the manual and these safety instructions before using the device. In case of contradicting information, the text of these safety instructions shall apply. In case of any doubt, the German version shall apply. The EU-declaration of conformity, certificates, safety instructions and manuals can be found at www.isafe-mobile.com, or requested from i.safe MOBILE GmbH. RESERVATION Technical Data is subject to change without notice. Changes, errors and misprints may not be used as a basis for any claim for damages. All rights reserved. i.safe MOBILE GmbH cannot be held responsible for any data or other loss and direct or indirect damages caused by any improper use of this device. EX-SPECIFICATIONS The IS-MP.1 is a device suitable for use in potentially explosive atmospheres classified as zones 1, 2, 21, 22 in accordance with directives 2014/34/EU and 2014/53/EU, as well as the IECEx scheme. EX-MARKINGS ATEX: II 2G Ex ib IIC T4 Gb II 2D Ex ib IIIC T135°C Db IP6X EU Type Examination Certificate: EPS 16 ATEX 1 119 X CE-designation: 2004 IECEx: Ex ib IIC T4 Gb Ex ib IIIC T135°C Db IP6X IECEx Certificate: IECEx EPS 16.0052X Temperature range: -20 °C ... +60 °C Manufactured by: i.safe MOBILE GmbH i_Park Tauberfranken 10 97922 Lauda-Koenigshofen Germany EU-DECLARATION OF CONFORMITY The EU-declaration of conformity can be found at the end of this manual. 4 FAULTS AND DAMAGES If there is any reason to suspect that the safety of the device has been compromised, it must be withdrawn from use and removed from any ex-hazardous areas immediately. Measures must be taken to prevent any accidental restarting of the device. The safety of the device may be compromised if, for example: Malfunctions occur. The housing of the device shows damage. The device has been subjected to excessive loads. The device has been stored improperly. Markings or labels on the device are illegible. It is recommended that a device which shows or which is suspected of faults and damages is returned i.safe MOBILE GmbH for inspection. EX-RELEVANT SAFETY REGULATIONS Use of this device assumes that the operator observes the conventional safety regulations and has read and understood manual, safety instructions and certificate. The following safety regulations must also be complied with: Inside ex-hazardous areas the cover of the USB interface has to be closed. To ensure the IP protection, it has to be ensured that all gaskets are present and functional. There must be no large gap between the two halves of the housing. The device may only be charged outside ex-hazardous areas using the i.safe PROTECTOR USB-cable or other equipment approved by i.safe MOBILE GmbH. USB-connections to other equipment are only allowed outside ex-hazardous areas using the i.safe PROTECTOR USB-cable or other equipment approved by i.safe MOBILE GmbH. The device may be charged only at temperatures in between 5 °C ... 35 °C. The device must not be exposed to abrasive acids or bases. The device must not be taken into zones 0 or 20. Only accessories approved by i.safe MOBILE GmbH may be used. FURTHER SAFETY ADVISES Do not touch the screen of the device with sharp objects. Dust particles and nails may scratch the screen. Please maintain the screen clean. Remove dust on the screen with a soft cloth gently, and do not scratch the screen. Charge the device under indoor conditions only. EN 5 Do not put the device in environments with excessive temperatures, as this could lead to heating of the battery, resulting in fire or explosion. Do not charge the device near any flammable or explosive substances. Do not charge the device in environments with much dust, humidity, or excessively high or low temperatures. Do not use the device in areas where regulations or legislatives prohibit the use. Do not expose the device or charger to strong magnetic fields, such as are emitted from induction ovens or microwaves. Do not attempt to open or repair the device. Improper repair or opening can lead to the destruction of the device, fire or explosion. Only authorized personnel are allowed to repair the device. Only use accessories approved by i.safe MOBILE GmbH. Power off the device in hospitals or other places where the use of mobile phones is prohibited. This device may affect proper work of medical equipment, such as pacemakers, so always keep a distance of at least 15 cm between the device and these devices. Observe all corresponding laws that are in force in the respective countries regarding the use of devices while operating a vehicle. Please power off the device and disconnect the charging cable before cleaning the device. Do not use any chemical cleaning agents to clean the device or the charger. Use a damp and anti-static soft cloth for cleaning. Do not discard old and abandoned batteries into the trash, send them to designated waste disposal locations or return them to i.safe MOBILE GmbH. WARNING i.safe MOBILE GmbH will not assume any liability for damages caused by disregarding any of these advices or by any inappropriate use of the device. MAINTENANCE/REPAIR Please note any legal requirements for periodic inspection. The device itself has no user-serviceable parts. It is recommended to perform inspections according to the safety regulations and advises. If there is a problem with the device, please contact your vendor or consult the service center. If your device is in need of repair, you can either contact the service center or your vendor. 6 BATTERY The battery in this device is not removable by the user. The battery is not fully charged when the device is purchased, but it contains enough energy to power on the device. To obtain best battery performance and battery life, let the battery discharge completely before charging it completely for the first three charging cycles. CHARGING THE BATTERY Connect the i.safe PROTECTOR cable with the USB connector at the back of the device. A further adapter may be necessary here. Connect the other side of the i.safe PROTECTOR with the socket of the power supply. After charging, remove the i.safe PROTECTOR from the charger. BATTERY USE In actual use the run time of the device varies with the working environment and usage. Please charge low battery; otherwise you may lose any files which are not saved. WARNING The device may only be charged at ambient temperatures in a range from 5 °C ... 35 °C. Please do not use charging equipment if the temperature exceeds this range. I.SAFE PROTECTOR The device contains specially designed safety circuits. Connecting the device to non-ex-approved equipment like a computer can endanger the safety of the device, as faults in the non-approved equipment could lead to a power surge into the device large enough to destroy the safety circuits. The i.safe PROTECTOR is a USB-cable for connecting the device with non-ex-approved equipment. It contains additional safety circuits to protect the device from possible faults in the non-ex-approved equipment. For this reason, charging and USB-connections are only allowed using the i.safe PROTECTOR. KEYS AND SPECIAL FEATURES (see illustration on page 2) 1 KEY 1: To read transponders. 2 KEY 2: For several Bluetooth function. 3 ON/OFF KEY: Short press to power On/Off the device. EN 7 4 USB PORT: HID (Human Interface Device) and to charge the battery. Do not open the USB port in hazardous areas! POWERING ON AND OFF THE IS-MP.1 To powering ON the device, press the [On/Off Key]. The screen lights up and the device is in running order. For powering Off the device, press the [On/Off Key]. The display indicates a 3 second countdown and turn off. READ OF TRANSPONDERS Hold the top of the device near to a transponder and make a short press on [Key 1]. If the transponder can be read, the display will indicate the transponder type and the UID and the device gives a short vibrate. If there is no transponder in reading area, the display will indicate "NO TAG" vibrate in a longer sequence. The multipen will indicate automatically supported transponders as follows: LF 125/134 kHz: EM 41xx, EM 42xx, HTS, FDX-B, HDX HF 13,56 MHz: ISO 15693, ISO 14443, NFC UHF 860 MHz ... 960 MHz BLUETOOTH CONNECTION Turn the IS-MP.1 ON [On/Off Key]. Press [Key 2] for turn On and Off the Bluetooth function. For pairing with other devices push and hold [Key 2]. The Display will indicate "Pairing Bluetooth ..." and after successful pairing the IS-MP.1 will be listed as RNBT-E5D5 in paired Bluetooth device. The display of the IS-MP.1 will indicate "End of pairing". For existing connection the display of the IS-MP.1 indicate a BT icon top right. For lost connection the BT icon will be framed. READ TRANSPONDERS ON PC OR ANDROIDTM DEVICE For reading the transponders via Bluetooth you have to install "WINDOWS TIDMULTIPEN V.1.x" on PC. For Android device install the application "TECTUS MultiPen" available on Google PlayTM Store. 8 HUMAN INTERFACE DEVICE (HID) Powering Off and connect the IS-MP.1 with the delivered USB cable to the USB port on your PC. The display of the IS-MP.1 lights up and indicate an USB icon on top right of the display. Open an Excel sheet and read a transponder. The UID of the transponder will be imported automatically to any position of cursor on PC. RECYCLING The crossed-out wheeled-bin symbol on your product, battery, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies in the European Union. Do not dispose of these products as unsorted municipal waste. Always return your used electronic products, batteries, and packaging materials to dedicated collection points. This way you help prevent uncontrolled waste disposal and promote the recycling of materials. More detailed information is available from the product retailer, local waste authorities, national producer responsibility organisations, or your local i.safe MOBILE GmbH representative. The content of this document is presented as it currently exists. i.safe MOBILE GmbH does not provide any explicit or tacit guarantee for the accuracy or completeness of the content of this document, including, but not restricted to, the tacit guarantee of market suitability or fitness for a specific purpose unless applicable laws or court decisions make liability mandatory. i.safe MOBILE GmbH reserves the right to make changes to this document or to withdraw it any time without prior notice. TRADEMARKS i.safe MOBILE and the i.safe MOBILE logo are trademarks of the i.safe MOBILE GmbH. Google, Google Play and Android are trademarks of Google Inc. Bluetooth® is a registered trademark of Bluetooth SIG, INC. worldwide. All other trademarks and copyrights are the properties of their respective owners. EN 9 DEUTSCH EINFÜHRUNG Dieses Dokument enthält Informationen und Sicherheitsvorschriften die für einen sicheren Betrieb des Geräts IS-MP.1 unter den beschriebenen Bedingungen unbedingt zu berücksichtigen sind. Nichtbeachtung dieser Informationen und Anweisungen kann gefährliche Folgen haben oder gegen Vorschriften verstoßen. Lesen Sie die Bedienungsanleitung und diese Sicherheitshinweise bevor Sie das Gerät benutzen. Im Falle widersprüchlicher Informationen gelten die deutschen Anweisungen in diesen Sicherheitshinweisen. Die aktuelle EU-Konformitätserklärung, Baumusterprüfbescheinigungen, Sicherheitshinweise und Bedienungsanleitung können unter www.isafe-mobile.com heruntergeladen oder bei der i.safe MOBILE GmbH angefordert werden. VORBEHALT Technische Änderungen behalten wir uns vor. Änderungen, Irrtümer und Druckfehler begründen keinen Anspruch auf Schadensersatz. Alle Rechte vorbehalten. Für Datenverluste oder andere Schäden gleich welcher Art, die durch den unsachgemäßen Gebrauch des Geräts entstanden sind, übernimmt die i.safe MOBILE GmbH keine Haftung. EX-SPEZIFIKATIONEN Das Gerät IS-MP.1 ist geeignet für den industriellen Einsatz in explosionsgefährdeten Bereichen der Zonen 1, 2, 21, 22 nach Richtlinien 2014/34/EU und 2014/53/EU und dem IECEx-System. EX-KENNZEICHNUNGEN ATEX: II 2G Ex ib IIC T4 Gb II 2D Ex ib IIIC T135°C Db IP6X EU-Baumusterprüfbescheinigung: EPS 16 ATEX 1 119 X CE-Kennzeichnung: 2004 IECEx: Ex ib IIC T4 Gb Ex ib IIIC T135°C Db IP6X IECEx-Zertifikat: IECEx EPS 16.0052X Temperaturbereich: -20 °C ... +60 °C Hersteller: i.safe MOBILE GmbH i_Park Tauberfranken 10 97922 Lauda-Königshofen Germany EU-KONFORMITÄTSERKLÄRUNG Die EU-Konformitätserklärung befindet sich am Ende dieser Anleitung. 10 FEHLER UND UNZULÄSSIGE BELASTUNGEN Sobald zu befürchten ist, dass die Sicherheit des Gerätes beeinträchtigt wurde, muss das Gerät außer Betrieb genommen und sofort aus explosionsgefährdeten Bereichen entfernt werden. Die unbeabsichtigte Wiederinbetriebnahme muss verhindert werden. Die Gerätesicherheit kann gefährdet sein, wenn z. B.: Fehlfunktionen auftreten. Am Gehäuse des Geräts Beschädigungen erkennbar sind. Das Gerät übermäßigen Belastungen ausgesetzt wurde. Das Gerät unsachgemäß gelagert wurde. Beschriftungen auf dem Gerät nicht mehr lesbar sind. Wir empfehlen ein Gerät, welches Fehler zeigt, oder bei dem Fehler vermutet werden, zu einer Überprüfung an die i.safe MOBILE GmbH zurückzusenden. EX-RELEVANTE SICHERHEITSVORSCHRIFTEN Die Benutzung des Geräts setzt beim Anwender die Beachtung der üblichen Sicherheitsvorschriften und das Lesen der Bedienungsanleitung, der Sicherheitshinweise und des Zertifikates voraus, um Fehlbedienungen am Gerät auszuschließen. Folgende Sicherheitsvorschriften müssen zusätzlich beachtet werden: Die USB-Abdeckung des Gerätes muss bei Verwendung in Ex-Bereichen vollständig geschlossen sein. Um den IP-Schutz zu gewährleisten, ist sicherzustellen, dass alle Dichtungen am Gerät ordnungsgemäß vorhanden sind. Zwischen den beiden Gerätehälften darf kein größerer Spalt erkennbar sein. Das Gerät darf nur außerhalb explosionsgefährdeter Bereiche über das i.safe PROTECTOR USB-Kabel oder anderes von i.safe MOBILE GmbH freigegebenes Zubehör geladen werden. USB-Datenverbindungen sind nur über das i.safe PROTECTOR USB-Kabel oder anderes von i.safe MOBILE GmbH freigegebenes Zubehör erlaubt. Das Gerät darf nur bei Umgebungstemperaturen zwischen 5 °C ... 35 °C geladen werden. Das Gerät darf keinen aggressiven Säuren oder Basen ausgesetzt werden. Das Gerät darf nicht in die Zonen 0, oder 20 eingebracht werden. Nur von i.safe MOBILE GmbH freigegebenes Zubehör darf verwendet werden. DE 11 WEITERE SICHERHEITSHINWEISE Berühren Sie das Display nicht mit scharfkantigen Gegenständen. Staub und Schmutz oder Ihre Fingernägel können die Displayscheibe zerkratzen. Bitte halten Sie die Displayscheibe sauber, indem Sie diese regelmäßig mit einem weichen Stofftuch reinigen. Laden Sie das Gerät nur in trockenen Innenräumen. Setzen Sie das Gerät keinen hohen Temperaturen aus, da dadurch die Batterie überhitzen kann, was zu Feuer oder im schlimmsten Fall zu einer Explosion führen kann. Laden Sie das Gerät nicht in der Nähe von brennbaren oder explosiven Substanzen. Laden Sie das Gerät nicht in feuchter, staubiger oder zu warmer oder zu kalter Umgebung. Benutzen Sie das Gerät nicht an Orten, wo das Benutzen verboten ist. Setzen Sie das Gerät oder das Ladegerät keinen starken elektrischen Magnetfeldern aus, wie sie z. B. von Induktionsherden oder Mikrowellenöfen ausgehen. Öffnen Sie das Gerät nicht selbst und führen Sie auch keine Reparaturen selbst durch. Unsachgemäße Reparaturen können zur Zerstörung des Geräts, zu Feuer oder zu einer Explosion führen. Das Gerät darf nur von autorisierten Fachleuten repariert werden. Verwenden Sie nur von i.safe MOBILE GmbH zugelassenes Zubehör. Schalten Sie das Gerät in Kliniken oder anderen medizinischen Einrichtungen aus. Dieses Gerät kann die Funktion von medizinischen Geräten wie Herzschrittmachern oder Hörhilfen beeinflussen. Halten Sie immer einen Sicherheitsabstand von mindestens 15 cm zwischen Gerät und einem Herzschrittmacher ein. Achten Sie bei der Verwendung des Geräts während der Steuerung eines Kraftfahrzeuges auf die entsprechenden Landesgesetze. Schalten Sie das Gerät aus und entfernen Sie das Ladekabel, bevor Sie das Gerät reinigen. Benutzen Sie keine chemischen Mittel zum Reinigen des Geräts oder des Ladegeräts. Reinigen Sie die Geräte mit einem weichen, angefeuchteten antistatischen Stofftuch. Akkus gehören NICHT in den Hausmüll. Als Verbraucher sind Sie dazu verpflichtet alte Akkus zur fachgerechten Entsorgung zurückzugeben. WARNUNG Die i.safe MOBILE GmbH übernimmt keine Haftung für Schäden, die durch Nichtbeachtung dieser Hinweise oder unsachgemäßen Gebrauch des Geräts entstehen. 12 WARTUNG/REPARATUR Beachten Sie eventuell gültige gesetzliche Richtlinien zu wiederkehrenden Prüfungen, wie z. B. die Betriebssicherheitsverordnung! Das Gerät selbst besitzt keine zu wartenden Teile. Es wird empfohlen, eine Überprüfung anhand der Kriterien in den Sicherheitsvorschriften und Sicherheitshinweisen durchzuführen. Bedarf Ihr Gerät einer Reparatur, wenden Sie sich bitte an ein autorisiertes Service Center oder Ihren Verkäufer. Reparaturen dürfen nur durch i.safe MOBILE GmbH oder autorisierte Service Center durchgeführt werden, da ansonsten die Sicherheit des Geräts nicht mehr gewährleistet ist. BATTERIE Die Batterie ist fest in dem Gerät eingebaut. Bei Anlieferung ist die Batterie nicht vollständig aufgeladen. Das Gerät lässt sich aber dennoch vollständig aktivieren. Zur Erreichung der besten Performance der Batterie sollte die Batterie die ersten dreimal vollständig entladen und anschließend wieder 100% aufgeladen werden. LADEN DER BATTERIE Kontaktieren Sie den mitgelieferten i.safe PROTECTOR mit der USB-Buchse des Geräts. Hier ist eventuell ein weiterer Adapter notwendig. Kontaktieren Sie anschließend den i.safe PROTECTOR mit dem Netzteil. Nach dem Ladevorgang trennen Sie bitte den i.safe PROTECTOR vom Netzteil. GEBRAUCH DER BATTERIE Im täglichen Gebrauch des Geräts hängt die Betriebszeit von den Gebrauchsgewohnheiten und den Umgebungsbedingungen ab. Sobald die Batterie einen niedrigen Ladezustand erreicht, laden Sie es entsprechend der Anleitung wieder auf. Falls dies nicht umgehend erfolgt, können nichtgespeicherte Daten verloren gehen. Wenn das Gerät für längere Zeit nicht geladen wird, schaltet es sich selbst ab. WARNUNG Die Batterie des Geräts darf nur innerhalb des Temperaturbereiches von 5 °C ... 35 °C geladen werden! Bitte laden Sie niemals außerhalb dieses Temperaturbereiches. DE 13 I.SAFE PROTECTOR Das Gerät enthält Sicherheitsschaltungen. Eine Verbindung des Geräts mit einem nicht Ex-zugelassenen Gerät, wie z. B. einem Computer, kann die Sicherheit des Geräts beeinflussen, da Fehler in dem nicht Ex-zugelassenen Gerät zu hohen Leistungen führen können, die die Sicherheitsschaltungen des Geräts zerstören könnten. Das i.safe PROTECTOR USB-Kabel enthält zusätzliche Sicherheitsschaltungen, die das Gerät vor möglichen Fehlern in angeschlossenen Geräten schützen. Aus diesem Grund sind Lade- und USB-Verbindungen nur über das i.safe PROTECTOR USBLadekabel erlaubt. TASTENBELEGUNG UND BESONDERHEITEN (siehe Abbildung auf Seite 2) 1 TASTE 1: Zum Auslesen eines Transponders. 2 TASTE 2: Für verschiedene Bluetooth-Funktionen. 3 AN-/AUS-TASTE: Kurzer Druck um das Gerät an- und auszuschalten. 4 USB-ANSCHLUSS: HID (Human Interface Device); Ladeanschluss der Batterie. Öffnen Sie niemals die USB-Abdeckung in Ex-relevanten Bereichen! AN- UND AUSSCHALTEN DES GERÄTS Zum Anschalten drücken Sie die [An-/Aus-Taste] bis das Display aufleuchtet. Das Gerät ist betriebsbereit. Zum Ausschalten drücken Sie die [An-/Aus-Taste]. Das Gerät schaltet sich nach 3 Sekunden ab. LESEN VON TRANSPONDERN Halten Sie die Spitze des IS-MP.1 an einen Transponder und drücken Sie die [Taste 1]. Kann der Transponder gelesen werden, zeigt das Display den Typ und die UID des Transponders an. Befindet sich kein Transponder im Lesebereich erscheint die Meldung ,,NO TAG". Der IS-MP.1 erkennt je nach Konfiguration folgende Transpondertypen automatisch: LF 125/134 kHz: EM 41xx, EM 42xx, HTS, FDX-B, HDX HF 13,56 MHz: ISO 15693, ISO 14443, NFC UHF 860 MHz ... 960 MHz 14 BLUETOOTH-VERBINDUNG Schalten Sie den IS-MP.1 an [An-/Aus-Taste]. Drücken Sie die [Taste 2] um die Bluetooth-Funktion an-/auszuschalten. Zum Paaren mit anderen (eingeschaltetes Bluetooth vorausgesetzt) Geräten drücken und halten Sie die [Taste 2]. Im Display erscheint ,,Pairing Bluetooth...". Nach erfolgreicher Paarung wird der IS-MP.1 als RNBT-E5D5 auf dem zu verbindenden Gerät erkannt werden. Im Display erscheint ,,End of pairing". Bei einer bestehenden Verbindung zeigt das Display des IS-MP.1 oben rechts ein Buetooth-Icon an. Unterbrochene Verbindungen werden durch ein umrahmtes Bluetooth-Icon angezeigt. TRANSPONDER MIT PC ODER ANDROIDTM AUSLESEN Bei einer Bluetooth-Verbindung können Sie den IS-MP.1 mit dem Programm ,,WINDOWS TIDMULTIPEN V.1.x" oder mit der Android-Applikation ,,TECTUS Multipen" (erhältlich im Google PlayTM Store) auslesen. HUMAN INTERFACE DEVICE (HID) Schalten Sie den IS-MP.1 ein und stellen Sie eine Verbindung mit dem PC her. Benutzen Sie dafür das mitgelieferte USB-Kabel. Die UID eines gelesenen Transponders wird nun automatisch an der Stelle eingetragen, an der sich der Cursor befindet. WIEDERVERWERTUNG Das Symbol der durchgestrichenen Abfalltonne auf Rädern, das auf dem Produkt, auf dem Akku, in der Dokumentation oder auf dem Verpackungsmaterial zu finden ist, bedeutet, dass elektrische und elektronische Produkte, Batterien und Akkus am Ende ihrer Lebensdauer einer getrennten Müllsammlung zugeführt werden müssen. Diese Vorschriften gelten in der Europäischen Union. Entsorgen Sie diese Produkte nicht über den unsortierten Hausmüll. Entsorgen Sie gebrauchte elektronische Produkte, Akkus und Verpackungsmaterial stets bei den entsprechenden Sammelstellen. Sie beugen so der unkontrollierten Müllbeseitigung vor und fördern die Wiederverwertung von stofflichen Ressourcen. Weitere Informationen erhalten Sie über den Händler, bei dem Sie das Produkt erworben haben, von regionalen Abfallunternehmen, staatlichen Behörden für die Einhaltung der erweiterten Herstellerhaftung oder dem für Ihr Land oder Ihre Region zuständigen i.safe MOBILE GmbH Vertreter. DE 15 Der Inhalt dieses Dokuments wird so präsentiert, wie er aktuell vorliegt. Die i.safe MOBILE GmbH übernimmt weder ausdrücklich noch stillschweigend irgendeine Gewährleistung für die Richtigkeit oder Vollständigkeit des Inhalts dieses Dokuments, einschließlich, aber nicht beschränkt, auf die stillschweigende Garantie der Markttauglichkeit und der Eignung für einen bestimmten Zweck, es sei denn, anwendbare Gesetze oder Rechtsprechungen schreiben zwingend eine Haftung vor. Die i.safe MOBILE GmbH behält sich das Recht vor, jederzeit ohne vorherige Ankündigung Änderungen an diesem Dokument vorzunehmen oder das Dokument zurückzuziehen. WARENZEICHEN i.safe MOBILE und das i.safe MOBILE Logo sind Marken der i.safe MOBILE GmbH. Google, Google Play und Android sind Marken von Google Inc. Bluetooth® ist eine weltweit eingetragene Marke der Bluetooth SIG, Inc. Alle weiteren Marken und Copyrights sind Eigentum ihrer jeweiligen Besitzer. 16 DE 17 EU-DECLARATION OF CONFORMITY EU Declaration of Conformity EU Konformitätserklärung according to directive 2014/34/EU, 2014/53/EU, 2011/65/EU (2015/863/EU) nach Richtlinie 2014/34/EU, 2014/53/EU, 2011/65/EU (2015/863/EU) The company i.safe MOBILE GmbH declares under its sole responsibility that the product to which this declaration relates is in accordance with the provisions of the following data, directives and standards: Die Firma i.safe MOBILE GmbH erklärt in alleiniger Verantwortung, dass Ihr Produkt auf welches sich diese Erklärung bezieht, den nachfolgenden Daten, Richtlinien und Normen entspricht: Name & address of the manufacturer in the EU i.safe MOBILE GmbH Name & Anschrift des Herstellers innerhalb der i_Park Tauberfranken 10 europäischen Gemeinschaft 97922 Lauda Koenigshofen Germany Description of the devices explosion protected RFID and NFC tag reader Beschreibung der Geräte explosionsgeschütztes RFID und NCF Tag Lesegerät type / Typ: IS-MP.1 Ex marking II 2G Ex ib IIC T4 Gb Ex Kennzeichnung II 2D Ex ib IIIC T135°C Db IP6X Type examination certificate 2014/34/EU EPS 16 ATEX 1 119 X issued by Baumusterprüfbescheinigung 2014/34/EU Bureau Veritas Consumer Product Services ausgestellt durch Germany GmbH Businesspark A96 86842 Tuerkheim, Germany identification number / Kenn-Nummer: 2004 Applied European directives 2014/34/EU, 2014/53/EU, 2011/65/EU Angewandte europäische Richtlinien (2015/863/EU) 2014/34/EU, 2014/53/EU, 2011/65/EU (2015/863/EU) Applied harmonized standards Angewandte harmonisierte Standards CE Marking CE-Kennzeichnung EN IEC 60079-0:2018; EN 60079-11:2012; EN IEC 62368-1:2020 + A11:2020; EN 301 489-3 V2.2.2; EN 300 328 V2.2.2; EN 300 330-2 V2.1.1 2004 Lauda Koenigshofen 07.12.2021 Dirk Amann Managing Director 1020CC05REV00_jru All rights reserved, i.safe MOBILE GmbH CONTACT/SERVICE CENTRE FOR FURTHER QUESTIONS PLEASE CONTACT OUR SERVICE CENTRE: i.safe MOBILE GmbH, i_Park Tauberfranken 10, 97922 Lauda-Koenigshofen, Germany support@isafe-mobile.com https://support.isafe-mobile.com WWW.ISAFE-MOBILE.COMAdobe PDF Library 16.0.3 Adobe InDesign 17.0 (Windows)