Instructions for SUNRICHER models including: SR-ZG9100A-S, ZigBee In Wall Smart Switch, SR-ZG9100A-S ZigBee In Wall Smart Switch
Reset L L N N OUT AC 100-240V S 1 C O M In-w all Sm rt Switch MAX:1.4A ( ) MAX:4.8A ( ) Ratings:1 0-24 V,5 /6 Hz Live Neutral Bypass Reset L L N N OUT AC 100-240V
5 giorni fa — ZigBee in wall smart switch based on latest ZigBee 3.0 protocol. • 100-240VAC Wide Input and Output Voltage. • Supports resistive loads, capacitive loads or ...
File Info : application/pdf, 4 Pages, 303.44KB
DocumentDocumentZigBee In Wall Smart Switch 70110018 Important: Read All Instructions Prior to Installation Function introduction Switch input "Reset" Key: factory reset of the switch, short press to turn on/off load S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz, MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N LED indicator, stays off when power on the switch, turns on after added to a zigbee hub, indicates (same status as connected load) when program the switch (network pairing, touchlink, factory reset) Load output (2-wire with No Neutral output) (3-wire with Neutral output) AC power input (2-wire with No Neutral input) (3-wire with Neutral input) Product Data Input Voltage 100-240VAC Output Voltage 100-240VAC Output Current Resistive load: max. 4.8A Capacitive/Inductive load: max. 1.4A Size(LxWxH) 45.5x45x20.3mm · ZigBee in wall smart switch based on latest ZigBee 3.0 protocol · 100-240VAC Wide Input and Output Voltage · Supports resistive loads, capacitive loads or inductive loads · 1 channel output, max. load up to 4.8A · Input and Output with Screw Terminals, Safe and Reliable · Enables to control ON/OFF of connected light source · ZigBee end device that supports Touchlink commissioning · Can directly pair to a compatible ZigBee remote via Touchlink without coordinator · Supports self-forming zigbee network without coordinator and add other devices to the network · Supports find and bind mode to bind a ZigBee remote · Supports zigbee green power feature and can bind max. 20 zigbee green power remotes · Compatible with universal ZigBee gateway products · Mini Size, Easy to be Installed into a standard size wall box · Radio Frequency : 2.4GHz · Waterproof grade: IP20 Main Features: · Can operate under two-wire connection with no neutral lead or three-wire connection with neutral lead · Soft start function, · Works with various types of switches momentary, toggle, three-way, etc. · Active element: semiconductor electronic switch, · To be installed in wall switch boxes of dimensions allowing for installation, conforming to provisions of applicable regulations, · The Bypass is an extension unit. The switch operates under the following loads: · Conventional incandescent and HV halogen light sources · ELV halogen lamps (with electronic transformers) · MLV halogen lamps (with ferromagnetic transformers) · Compact fluorescent CFL tube lamps with electronic ballast · Fluorescent tube lamps with electronic ballast · Supported light sources (power factor > 0.5) with minimal power of 3W using the Bypass (depending on the type of load) ZigBee Clusters the device supports are as follows: Input Clusters · 0x0000: Basic · 0x0003: Identify · 0x0004: Groups · 0x0005: Scenes · 0x0006: On/off · 0x0702: Simple Metering · 0x0b04: Electrical Measurement · 0x0b05: Diagnostics Output Clusters · 0x0019: OTA Safety & Warnings · DO NOT install with power applied to device. · DO NOT expose the device to moisture. Operation 1.Do wiring according to connection diagram correctly. 2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system. 3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network) Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part "Factory Reset Manually". Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller. Step 4: Connected light will blink 5 times and then stay solid on, then the device will appear in your controller's menu and can be controlled through controller or hub interface. S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N Step 3: Re-power on the device to set it into network pairing mode (connected light flashes twice slowly), 15 seconds timeout, repeat the operation. Bypass Live Neutral 4. TouchLink to a Zigbee Remote Step 2: Bring the remote or touch panel within 10cm of the lighting device. Step 3: Set the remote or touch panel into Touchlink commissioning, please refer to corresponding remote or touch panel manual to learn how. Step 4: There shall be indication on the remote for successful link and connected light will flash twice. Zigbee Remote < 10cm Bypass S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N Step 1: Method 1: Short press "Reset" button (or re-power on the device) 4 times to start Touchlink commissioning immediately, 180S timeout, repeat the operation. Method 2: Re-power on the device, Touchlink commissioning will start after 15S if it's not added to a zigbee network, 165S timeout. Or start immediately if it's already added to a network, 180S timeout. Once timeout, repeat the operation. Live Neutral Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote. 2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes. 3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink. 4) After TouchLink, the device can be controlled by the linked remotes. 5. Removed from a Zigbee Network through Coordinator or Hub Interface From your ZigBee controller or hub interface, choose to delete or reset the lighting device as instructed. The connected light blinks 3 times to indicate successful reset. 7. Factory Reset through a Zigbee Remote (Touch Reset) Note: Make sure the device already added to a network, the remote added to the same one or not added to any network. Step 2: Bring the remote or touch panel within 10cm of the lighting device. Step 3: SSet the remote or touch panel into Touch Reset procedure to reset the device, please refer to corresponding remote or touch panel manual to learn how. Zigbee Remote < 10cm S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N Step 1: Re-power on the device to start TouchLink Commissioning, 180 seconds timeout, repeat the operation. Step 4: There shall be indication on the remote and connected light flashes 3 times for successful reset. Live Neutral Bypass 8. Find and Bind Mode Note: Make sure the device and remote already added to the same zigbee network. Step 2: Set the remote or touch panel (target node) into find and bind mode, and enable it to find and bind initiator, please refer to corresponding remote or touch panel manual. Step 3: There shall be indication on the remote or touch panel that it bind the device successfully and can control it then. Zigbee Remote Bypass S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N Step 1: Short press "Reset." button 3 times (Or re-power on the device (initiator node) 3 times) to start Find and Bind mode (connected light flashes slowly) to find and bind target node, 180 seconds timeout, repeat the operation. 6. Factory Reset Manually Note: 1) If the device is already at factory default setting, there is no indication when factory reset again . 2) All configuration parameters will be reset after the device is reset or removed from the network. Step 2: Connected light will blink 3 times to indicate successful reset. Live Neutral Bypass S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N Step 1: Short press "Reset." key for 5 times continuously or re-power on the device for 5 times continuously if the "Prog." key is not accessible. Live Neutral 9. Learning to a Zigbee Green Power Remote Step 2: Set the green power remote into Learning mode, please refer to its manual. Step 3: Connected light will flash twice to indicate successful learning. Then the remote can control the device. Zigbee Green Power Remote Bypass S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N Live Neutral Note: Each device can learn to max. 20 zigbee green power remotes. Step 1: Short press "Reset." button 4 times (Or re-power on the device 4 times) to start Learning mode (connected light flashes twice), 180 seconds timeout, repeat the operation. 10. Delete Learning to a Zigbee Green Power Remote Step 2: Set the paired green power remote into Learning mode, please refer to its manual. Zigbee Green Power Remote Step 3: Connected light will flash 4 times to indicate successful deleting. Bypass S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N Step 1: Short press "Reset." button 3 times (Or re-power on the device 3 times) to start delete Learning mode (connected light flashes slowly), 180 seconds timeout, repeat the operation. Live Neutral 11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required) Zigbee Remote S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N < 10cm TouchLink S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N Step 1: Short press "Reset." button 4 times (Or re-power on the device 4 times) to enable the device to setup a zigbee network (connected light flashes twice) to discover and add other devices, 180 seconds timeout, repeat the operation. Bypass Live Neutral Wiring Diagram Compatible load types and recommended values of power for supported loads: Supported load types Resistive loads Conventional incandescent and halogen light sources Capacitive loads Fluorescent tube lamp (compact / with electronic ballast), electronic transformer, LED 100-240V~ 100-240V~ 20-1000W @ 230V 20-500W @ 110V Using Bypass: 3-300W @ 230V 3-150W @ 110V No Bypass Used: 20-300W @ 230V 20-150W @ 110V Inductive loads Ferromagnetic transformers 20-300W @ 230V 20-150W @ 110V Notes for the diagrams: L - terminal for live lead N - terminal for neutral lead Out - output terminal of the switch (controlling connected light source) S1 - terminal for switch (has the option of entering the device in inclusion/exclusion mode) COM - terminal for grounding to the switch connected to the switch Supported external switch types (should be configured by factory setting): 1) Push switch (default factory setting) 2) Normal On/Off switch (should be configured by factory setting upon request) (1) 2-Wire Connection With No Neutral Lead With PUSH LV With PUSH PUSH S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N PUSH S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N Bypass Bypass Live Neutral Live Neutral NOTE: Switch connected to the S1 terminal activates the basic functionality of the dimmer (turning the light on/off). The Bypass is a device designed to work with the micro smart dimmer. It should be used in case of connecting LED bulbs or energy saving compact fluorescent lamps. The Bypass prevents flickering of the LED lights and glowing of the turned off compact fluorescent lamps. In the case of 2-wire connection, the Bypass allows to reduce minimum power of load required by the dimmer for correct operation. The Bypass provides powering of the dimmer in case of controlling the low loads of minimum power down to 3W (for cos>0.5). (2) 3-Wire Connection With Neutral Lead With PUSH LV With PUSH PUSH S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N PUSH S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N Live Neutral Live Neutral NOTE: Switch connected to the S1 terminal activates the basic functionality of the dimmer (turning the light on/off). (3) Multiple Momentary or Push Switches Connection With PUSH LV S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N With PUSH Live Neutral S1 In-wall Smart Switch COM Ratings:100-240V,50/60Hz MAX:4.8A ( ) Reset MAX:1.4A ( ) OUT AC 100-240V L LN N