Wireless Microphone User Manual
Model: H19
ID Diagram
Transmitter Components:
- ① Windproof Net (防风网)
- ② Connection indicator light (连接指示灯)
- ③ Noise reduction indicator light (降噪指示灯)
- ④ Reverberation indicator light (混响指示灯)
- ⑤ Mute indicator light (静音指示灯)
- ⑥ Microphone Type-C charging port (麦克风Type-C充电接口)
- ⑦ Microphone clip (麦克风夹)
- ⑧ Power switch/connection (电源开关/连接)
Receiver Components:
- ⑨ Port to connect phone (手机接口)
- ⑩ Indicator light (指示灯)
- ⑪ Receiver charging port (接收端充电接口)
The diagram also shows a smartphone connected to the receiver, with a label pointing to the 'Switch key' on the microphone and 'Indicator light always on' on the receiver.
How to Use
- Connect the receiver to your phone's port.
- Press the microphone's switch key. The indicator light will turn green, indicating it is powered on.
- The receiver's indicator light will remain constantly on. Open your phone's camera, live streaming app, or other applications to begin receiving sound via the microphone.
UI Function
Microphone Transmitter
| Function/Status | Button | LED Indicator |
|---|---|---|
| Power on | Short press the power button for 1 second | Connection indicator light green flashing slowly |
| Power off | Short press the power button for 2 seconds | All lights went out |
| Unconnected | Connection indicator light green flashing slowly | |
| Connected | The connection indicator light remains on | |
| Noise reduction | Default noise reduction | The noise reduction indicator light is always on |
| Reverberation | Double click the power switch | Off: Reverb indicator light; On: Reverb indicator light on |
| Silent mode | Click on the power switch | Off: Mute indicator light off; On: Mute indicator light on |
| Charging | The charging red light is always on; all lights are off when fully charged. | |
| LOW BATTERY | The charging indicator light flashes once every 5 seconds. |
Receiver
| Function | Operate | LED Indicator |
|---|---|---|
| Power on | Blue light flashing | |
| Connect transmitter | The blue light is constantly on |
Packing List
Content of packing:
- (1) Microphone transmitter
- (2) Receiver
- (3) Charging cable
- (4) User manual
FCC Compliance Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Regulatory Marks: [CE mark] [FCC mark] [WEEE disposal symbol] [Product Safety mark] [Compliance mark]
