for Uniden models including: BCT15X, Uniden,Uniden,Uniden,BearTracker,Scanner,(BCT15X),with,9,000,Channels,,TrunkTracker,III,Technology,,Base/Mobile,Design,,Close,Call,RF,Capture,Technology,with,Location-Based,Scanning,,-,Black,Color,B09YXH5HGM,B09YTST337,B09YTTXLW9,B002IT1C8U,B09YTKQNH8
BCT15X User Manual (PDF) Uniden Uniden Uniden,BearTracker,Scanner,(BCT15X),with,9,000,Channels,,TrunkTracker,III,Technology,,Base/Mobile,Design,,Close,Call,RF,Capture,Technology,with,Location-Based,Scanning,,-,Black,Color,B09YXH5HGM,B09YTST337,B09YTTXLW9,B002IT1C8U,B09YTKQNH8
Amazon.com: Uniden BearTracker Scanner (BCT15X) with 9,000 Channels, TrunkTracker III Technology, Base/Mobile Design, Close Call RF Capture Technology with Location-Based Scanning, - Black Color : Electronics
File Info : application/pdf, 42 Pages, 916.90KB
DocumentDocumentGeneral Attenuation Audio Output Power Scan Rate Search Rate External Jacks 20dB nominal 3W nominal into 8 speaker 30mW nominal into 32 stereo headphone 100 channels per second max (Conventional mode) 300 steps per second max (5kHz steps only) Antenna Jack: BNC Type Phone Jack: 3.5mm (1/8 in.) Stereo Type Ext.SP Jack: 3.5mm (1/8 in.) Monaural Type REC.Out Jack: 3.5mm (1/8 in.) Stereo Type Ext. DC Power and Orange Wire Jack 3 pin (Center Orange Wire) DC Power Jack: 5.5mm (1/5 in.) (Center Positive) GPS/Remote Interface Jack: D Sub 9pin Male Type Remote Interfase Jack (front panel): 4-pin Mini Custom Type Internal Speaker 8.0 5.0W Max. 77mm (3.0 in.) Power Requirements DC:11V to 16.6V(Ext.DC Power Jack or DC Power Jack) AC Adapter (13.8V DC 750mA Regulated) (AD-1009) Operating Temperature Nominal: -20°C to +60°C -4°F to +140°F Close Call: -10°C to +60°C +14°F to +140°F Size 7.2 in.(W) x 5.9 in.(D) x 2.2 in.(H) Weight 3.42 lbs Remote Functions Direct PC control Database management Wired cloning Display 64 x 128 Full Dot Matrix LCD with Orangecolor back light Sensitivity (nominal) 12dB SINAD 0.4V 25-27.995 MHz AM 0.3V 28-53.98 MHz NFM 0.6V 54-71.95 MHz WFM 0.2V 72-75.995 MHz FM 0.5V 76-107.9 MHz FMB 0.3V 108-136.9916 MHz AM 0.3V 137-173.9875 MHz NFM 0.5V 174-215.95 MHz WFM 0.3V 216-224.98 MHz NFM 0.3V 225-379.975 MHz AM 0.3V 380-512 MHz NFM 0.3V 758-960 MHz NFM 0.4V 1240-1300 MHz NFM Signal Noise Ratio (nominal) 48dB 25-27.995 MHz AM 41dB 28-53.98 MHz NFM 54dB 54-71.95 MHz WFM 48dB 72-75.995 MHz FM 60dB 76-107.9 MHz FMB 50dB 108-136.9916 MHz AM 41dB 137-173.9875 MHz NFM 54dB 174-215.95 MHz WFM 41dB 216-224.98 MHz NFM 50dB 225-379.975 MHz AM 40dB 380-512 MHz NFM 41dB 758-960 MHz NFM 37dB 1240-1300 MHz NFM Close Call Sensitivity (nominal) 160V VHF Low1 Band 110V VHF Low2 Band 90V Air Band 90V VHF High1 Band 100V VHF High2 Band 110V 160V UHF Band 800MHz+ Band Frequency Range Frequency Modulation Step Range (MHz) (kHz) Name 25.0000- AM 26.9600 5 Petroleum Products & Broadcast Pickup 26.9650- AM 27.4050 5 CB Class D Channel 27.4100- AM 27.9950 5 Business & Forest Products 28.000029.6800 NFM 20 10 Meter Amateur Band 29.700049.9900 NFM 10 VHF Low Band 50.000053.9800 NFM 20 6 Meter Amateur Band 54.000071.9500 WFM 50 VHF TV 72.0000- FM 75.9950 5 Intersystem & Astronomy 76.000087.9500 88.0000107.9000 108.0000136.9916 137.0000143.9875 144.0000147.9950 148.0000150.7875 150.8000161.9950 162.0000173.9875 174.0000215.9500 216.0000224.9800 225.0000379.9750 WFM FMB AM NFM NFM NFM NFM NFM WFM NFM AM 50 VHF TV 100 FM Broadcast 8.33 Aircraft Band 12.5 Military Land Mobile 5 2 Meter Amateur Band 12.5 Military Land Mobile 5 VHF High Band 12.5 Federal Government 50 VHF TV 20 1.25 Meter Amateur Band 25 Military Aircraft Band 380.0000399.9875 400.0000405.9875 406.0000419.9875 420.0000449.9875 450.0000469.9875 470.0000512.0000 758.0000787.99375 788.0000805.99375 806.0000823.9875 849.0125868.9875 894.0125960.0000 NFM NFM NFM NFM NFM NFM NFM NFM NFM NFM NFM 12.5 Military Land Mobile 12.5 Miscellaneous 12.5 Federal Government Land Mobile 12.5 70 cm Amateur Band 12.5 UHF Standard Band 12.5 UHF TV 6.25 Public Service Band 6.25 Public Service Band 12.5 Public Service Band 12.5 Public Service Band 12.5 Public Service Band 1240.00001300.0000 NFM 25 25 cm Amateur Band Special Functions Band Scope Function Frequency Span 0.2 MHz To 500 MHz Frequency Step 5 kHz To 100 kHz Two-Tone-Sequential 250.0-3500.0Hz , 0.1Hz Step Programmable WX Alert 1050 Hz Tone System NWR-SAME System (Warning / Watch / Advisory) Supported trunking systems Motorola Systems: Type I, II, II/I (hybrid) EDACS Systems: FM, NFM, and SCAT LTR Systems Dynamic memory allocation capacity Systems: 500 max Groups: 20 per system Site: 1000 max (All) 256 per system Channels: 9000 max (21120 memory blocks) Channels per Trunked System: 500 max Heterodyne System 1st IF: 380.7 to 380.8 MHz / 265.5 to 265.6 MHz 2nd IF: 10.8 MHz 3rd IF: 450 kHz CTCSS and DCS Tones CTCSS Tone Frequencies - 50 frequencies total (Hz) 67.0 69.3 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100. 103. 107. 110. 114. 118. 123. 127. 0 5 2 9 8 8 0 3 131. 136. 141. 146. 151. 156. 159. 162. 165. 167. 8 5 3 2 4 7 8 2 5 9 171. 173. 177. 179. 183. 186. 189. 192. 196. 199. 3 8 3 9 5 2 9 8 6 5 203. 206. 210. 218. 225. 229. 233. 241. 250. 254. 5 5 7 1 7 1 6 8 3 1 DCS Tone Codes - 104 codes total 023 025 026 031 032 036 043 047 051 053 054 065 071 072 073 074 114 115 116 122 125 131 132 134 143 145 152 155 156 162 165 172 174 205 212 223 225 226 243 244 245 246 251 252 255 261 263 265 266 271 274 306 311 315 325 331 332 343 346 351 356 364 365 371 411 412 413 423 431 432 445 446 452 454 455 462 464 465 466 503 506 516 523 526 532 546 565 606 612 624 627 631 632 654 662 664 703 712 723 731 732 734 743 754 Included With Your Scanner Scanner AC Adapter Vehicle Accessory Power Cord Three-Wire Harness Mounting Bracket and Hardware Antenna Serial Programming Cable O/M on CD ROM Other Printed Materials Mounting Sleeve and keys (Optional for BCT15X; Included with BCD996XT) Setting Up Your Scanner These guidelines will help you install and set up your new scanner: The scanner can be placed on a convenient surface in your home as a base station, and connected to a standard outlet that supplies 120VAC, 60Hz. You must use either the supplied antenna or an electrically correct outdoor antenna, properly and safely mounted at your chosen site. The scanner is also designed to accommodate either DIN-E and ISO-DIN automotive mounting configurations using a DIN-E sleeve and keys, (Part Number DIN-0001, BCD996XT: Included; BCT15X: Optional). The unit can also be placed above, beneath, or in the dash of your vehicle using the supplied bracket and mounting hardware. If your scanner receives interference or electrical noise, move the scanner or its antenna away from the source. To improve the scanner's reception, use an optional external antenna designed for multi-band coverage. (You can purchase this type of antenna at a local electronics store). If the optional antenna has no cable, use 50 coaxial cable for lead-in. A mating plug might be necessary for the optional antennas. Use an optional stereo earphone or sterreo headset with proper impedance (32 ) for private listening. Read the precautions at General Precautions. Do not use the scanner in high-moisture environments such as the kitchen or bathroom. Avoid placing the scanner in direct sunlight or near heating elements or vents. Power Related Issues Important: To prevent memory from being corrupted, do not unplug the AC adapter during the time the memory is accessed for programming or auto store. Notes: If when you connect the AC adapter the [VOL] /Power Switch is ON, the scanner may not power on. Should this occur, simply turn the control OFF, then ON again. If the scanner loses power (as when you turn off your car's ignition with the scanner's power switch on), it can lose some system settings such as display color and backlight. To ensure that such settings persist, either change the setting using the scanner's menu or power the scanner off then back on using the power switch after making such setting changes. When you turn off the scanner using the power switch, the scanner remembers the last settings and mode. When you turn power back on, it resumes the previous mode. Base Station This is the simplest approach to let you get started quickly. Decide on a location that is convenient to a nearby wall outlet, has desk space to let you complete your programming worksheets, will safely allow the indoor antenna to be extended, or near a window to use an outdoor antenna. To secure the radio to a surface, by means of the mounting bracket, follow the steps below: 1. Attach the four protective mounting feet to the mounting bracket when you casually use the scanner on a flat surface. Should you desire to permanently mount the scanner, remove the feet and use wood screws through the bracket as described in Steps 2 and 3. 2. Use the bracket as a template to mark positions for the two mounting screws. 3. At the marked positions, drill holes slightly smaller than the screws. 4. Align the bracket with the threaded holes on the sides of the radio case so the bracket is beneath the radio. Secure the bracket using the two threaded knobs. Never overtighten the knobs. Once the radio is positioned, connect it to a source of AC power using the supplied 13.8V, 750 mA AC adapter. Insert the barrel of the AC adapter to the jack on the rear, upper right side of the radio marked. Insert the connector of the supplied indoor telescoping antenna to the BNC Antenna Connector and apply moderate pressure to secure it. Setting Up an Audio Recording Device or Computer Recording It is best if you plan ahead when you initiate the basic setup of the scanner if you include the components to record incoming reception. You need an audio recording device which can be controlled by a Voice Operated module (VOX) either externally or from within the unit and the correct connecting cable. The REC (record) jack on the rear apron provides a constant-level audio output which is not affected by the setting of the volume control. Use a mono or stereo cable that ends in a 3.5mm plug for the scanner. The recorder might have its own requirements as to the proper plug. Check the recorder's instructions to be sure. Connect the cable to an external or internal VOX control so that the recorder operates when audio is present. You can also connect the cable to the appropriate input jack on your PC so that with controlling software, you can record to your hard disk. In order for the function to operate, you must set the channel to record. You must also set the system's record option to either All Channel, which will record all channels regardless of any channel's setting, or Marked Channel which only lets recording occur if you have selected record for that channel. Which you choose will depend on various factors. Vehicle Installation You can mount your scanner in your vehicle, using either the supplied bracket or the optional DIN-E sleeve. Mounting Using the Bracket With the bracket removed from the radio, use the holes in the bracket as a template to initially mark the location you plan to use in your vehicle. Be absolutely certain of what might be behind the mounting surface before making any holes, be it above, or below, or in front of your dash, armrest console, or other location. If you drill carelessly, expensive damage can result. If in doubt, consult your vehicle dealer's service department or a qualified professional installer. Important: AVOID AIRBAG DEPLOYMENT ZONES. Ignoring this installation concern may result in bodily harm and the inability of the airbag to perform properly. 1. Using appropriate screws or other hardware, secure the bracket. 2. Insert the scanner and insert the bracket knobs to lock the scanner in position. 3. Attach the Cigarette Lighter Power Cord to the rear of the scanner and plug the adapter end into a dash mounted 12V DC socket. 4. Attach a suitable mounted mobile antenna to the antenna jack on the back of the scanner. Mounting Using the DIN-E Sleeve (Option for BCT15X) If you are unsure about how to install your scanner in your vehicle using the optional DIN-E sleeve, consult your automobile manufacturer, dealer, or a qualified installer. Before installing, confirm that your scanner fits in the desired mounting area and you have all the necessary materials to complete the task. Your scanner requires a 2 x 7-1/8 x 5-5/16 inch (50 x 180 x 135 mm) mounting area. Allow an additional 2-3/8 inch (60mm) space behind the unit for connectors and wires. To purchase the DIN-E sleeve and included Removal Keys, visit http://www.unidendirect.com/ and order part number, DIN-0001. 1. Remove the bracket if it is attached. 2. Remove the four Philips screws from four small tabs on the rear of the case that secure the outer metal case and pull off the case (toward the rear) with care. 3. Install the DIN sleeve into the opening in your dashboard, lip facing out. 4. Push out the top and bottom tabs to hold the sleeve firmly in place. 5. Before inserting the scanner in the sleeve, attach the cable from the previously mounted antenna. Attach the DC Power leads. RED goes to a positive (+)connection on your fuse block while BLACK connects to the vehicle's chassis ground (). 6. Connect the ORANGE lead to one side of the headlamp switch so that when you activate the headlights, the scanner's LCD display changes intensity. Be sure all the connections are routed away from any potentially pinching or slicing sheet metal. 7. Slowly slide the scanner into the sleeve until it locks in place. 8. To remove the unit, fully insert the removal keys into each slot on the left and right edges of the front panel. Carefully slide the radio from the sleeve. Note: If you plan to connect a GPS unit or external speaker at a later time, expect to remove the unit for ease of making those connections. Removing the Scanner from the DIN-E Sleeve If you plan to connect other devices or wires to the radio, such as a GPS unit, at a later time, you should plan to remove the scanner from the DIN-E sleeve. This is easily done using the provided Removal Keys that come with the optional DIN-E sleeve. Refer to the illustration that follows, showing the Removal Keys. Fully insert both Removal Keys into the slots on the left and the right edges of the radio's dress panel. You cannot remove the radio with only one key. Press in fully,and do not twist the keys. The radio will unlock from the sleeve making withdrawal from the sleeve possible. Store the keys in a safe place for future use. Mounting Using ISO Technique Some vehicles can take advantage of another approach to mounting a radio in a vehicle, called the ISO technique. However, this technique requires a very detailed and thorough knowledge of the technique. Therefore, we strongly suggest that if you have any doubt about your experience and abilities, please consult with a professional installer who is familiar with the ISO approach to radio installation. To begin the process, it is first necessary to remove the scanner's outer metal sleeve from the inner chassis. Unthread the four screws in the rear of the unit. Slide the cover toward the rear and off. Once the sleeve is removed, you will see threaded, metric machine screw holes on either side of the chassis cabinet. Uniden does not supply these screws. Their diameter, length, and screw type should be chosen by a qualified installer based on the internal vehicle bracket which will be used in securing the scanner chassis. Once the original radio is removed from the vehicle dash and the fit of the scanner is correct, be sure to connect all the power, audio, antenna, and any other cables or wires, to the scanner before the scanner is secured. The following illustration is a typical example of the ISO technique and the general side mounting screw holes often encountered. It does not actually represent the Uniden scanner nor your vehicle's mounting bracket. Only a professional installer will be able to determine the best and correct approach. Removing the Display Sticker Before you use the scanner for the first time, remove the protective plastic film over the display. Connecting an Optional Antenna The scanner's BNC connector makes it easy to connect a variety of optional antennas, including an external mobile antenna or outdoor base station antenna. Note: Always use 50-ohm, RG-58, or RG-8, BNC terminated coaxial cable to connect an outdoor antenna. If the antenna is over 50 feet from the scanner, use RG-8 low-loss dielectric coaxial cable. Cable loss increases with higher frequency. Connecting an Earphone/Headphone For private listening, you can plug a 1/8-inch (3.5 mm) mini-plug earphone or headphones (not supplied) into the headphone jack on the front of your scanner. This automatically disconnects the internal speaker. See the Earphone Warning for important information about using an earphone/headphone. WARNING! Never connect anything other than the recommended amplified extension speaker to the scanner's headphone jack. Damage to the scanner might occur. Connecting an Extension Speaker In a noisy area, an optional amplified extension speaker, positioned in the right place, might provide more comfortable listening. Plug the speaker cable's 1/8-inch (3.5-mm) mini-plug into your scanner's back-panel Ext. Sp. Jack. WARNING! Never connect any part of the headphone jack to the antenna jack or connect the radio to an installation where the antenna and audio connection are grounded. This might also damage the scanner. To determine whether the information on this page applies to your scanner, see the tags at the bottom of the page. Compatible GPS receivers Configuring your scanner Connecting the receiver Troubleshooting Compatible GPS receivers You can connect your scanner to any GPS receiver that meets the following criteria: Outputs NMEA-0183 v3.01-compliant location data Outputs both the Global Positioning System Fix ( GGA ) and Recommended Minimum Specific GNSS ( RMC ) data sentences Provides a serial data (RS-232) connection Configuring your scanner 1. Go to the Settings menu and select Set Serial Port . 2. Select Set Baud Rate. 3. Select Set Rear Port. 4. Select 4800 bps for the baud rate. Connecting the receiver 1. Plug your GPS receiver's RS232 cable directly into the DB9 connector on the back of the scanner. 2. When the scanner recognizes the GPS input, it displays a confirmation message and shows the GPS icon on the display. 3. If the GPS receiver does not have a lock on the satellites, the scanner displays Searching for Satellite . Troubleshooting If you can't get the scanner to recognize the GPS receiver: Check the receiver's baud rate. Most compatible GPS receivers use a baud rate of 4800 bps, but it's possible your receiver is using a non-standard baud rate. Set the scanner's baud rate to match the GPS receiver's. Check the receiver's output mode. Some receivers have proprietary signalling modes that are not NMEA compliant, but you can usually set them to use a NMEA compliant mode. If the scanner recognizes the GPS receiver but doesn't lockout systems as you expected: Make sure the GPS receiver has a lock on the satellites. Check the location configuration for the sites and channel groups in the system. 1. For each site or channel group, go to the Set LocationInfo menu. 2. Check the range, latitude, and longitude settings to make sure they are correct. 3. Make sure the Set GPS Enable option is set to Yes . Please note that these pages are meant as general instructions. While most of the information here applies to all scanners, some options may not be available on certain scanner models. Modelspecific options are indicated in the text. Conventional Systems EDACS SCAT Systems EDACS Trunked Systems LTR Trunked Systems Motorola Trunked Systems Digital scanners only Standard P25 Trunked Systems Single Frequency P25 Trunked Systems General scanning information Please note that these pages are meant as general instructions. While most of the information here applies to all scanners, some options may not be available on certain scanner models. Modelspecific options are indicated in the text. Radio Systems Overview Deciphering Trunked Systems Location-based Scanning Scanning Legally This guide is optimized for the following web browsers: Internet Explorer 7.0 and later Mozilla Firefox 3.0 and later Google Chrome Safari 3.1.2 Opera 9.61 If you have difficulty viewing this guide in your current browser, please try downloading one of the browsers listed. Assigning an SNT SNTs can range from 0 to 999 . Systems can have the same SNT, but you will get a warning when you create multiples. (This includes SNTs assigned to the Close Call Hits system or any search ranges.) To a system : 1. Open the Program System menu. 2. Select the system you want to assign the number tag to. 3. Select Edit Sys Option, then select Set Number Tag. 4. Enter the number tag you want to use for this system. To the Close Call Hits system : 1. Open the Close Call menu. 2. Select Hits with Scan, then select Set Number Tag. 3. Enter the number tag you want to use for the Close Call Hits system. To a service search range : 1. Open the Search for... menu. 2. Select Edit Service, then select the service search range you want to assign the number tag to. 3. Select Search with Scan, then select Set Number Tag. 4. Enter the number tag you want to use for this search range. To a custom search range : 1. Open the Search for... menu. 2. Select Edit Custom, then select the custom search range you want to assign the number tag to. 3. Select Search with Scan, then select Set Number Tag. 4. Enter the number tag you want to use for this custom search range. Assigning a CHNT You can assign CHNTs to channels even if the system does not have an assigned SNT. However, without an SNT, you can only navigate to these channels from within that system itself. CHNTs can be duplicated within their own system, but you will see a warning when you create multiples. CHNTs can range from 0 to 999 . 1. Open the Program System menu. 2. Select the system containing the channel you want to assign the number tag to. 3. Select Edit Group, then select the channel group you want. 4. Select Edit Channel, then select the channel you want to assign the number tag to. 5. Select Set Number Tag. 6. Enter the number tag you want to use for this channel. Using Number Tags To navigate directly to: Key Sequence Example A system or search range A channel in the current syste m A channel in a different syste m 1. Tap HOLD. If the SNT is 4 , 2. Enter the enter HOLD / 4 / · / MENU. SNT + ·. 3. Tap MENU . 1. Tap HOLD. If the CHNT is 27, 2. Enter the enter HOLD / 27 / MENU. CHNT. 3. Tap MENU . 1. Tap HOLD. If the SNT is 4 and the 2. Enter the CHNT is 27, SNT follow enter HOLD / 4 / · / 27 / ME ed by the NU. decimal point. 3. Enter the CHNT. 4. Tap MENU . Notes: If two systems have the same SNT, they will be selected in sequence (i.e. the first time you select the SNT, the scanner will go to the first system assigned with that SNT; if you select the same SNT again, it will go to the 2nd system assigned with that SNT, and so on). If two channels in the same system have the same CHNT, they will be selected in sequence (i.e. the first time you select the CHNT, the scanner will go to the first channel in that system assigned with that CHNT; if you select the same CHNT again, it will go to the 2nd channel assigned with that CHNT, and so on). Assigning an SQK Multiple systems, sites, and search ranges can share the same SQK. All systems and sites assigned to the same SQK will be enabled (or disabled) when you enter the Quick Key. SQKs range from 0 to 99 . To a conventional system: 1. Open the Program System menu. 2. Select the system you want to assign the Quick Key to. 3. Select Edit Sys Option, then select Set Quick Key. 4. Enter the Quick Key you want to use for this system. To a trunked system: 1. Open the Program System menu. 2. Select the system you want to assign the Quick Key to. 3. Select Edit Site, then select the site you want. 4. Select Set Quick Key, then enter the Quick Key you want to use for this site. To the Close Call Hits system : 1. Open the Close Call menu. 2. Select Hits with Scan, then select Set Quick Key. 3. Enter the Quick Key you want to use for the Close Call Hits system. To a service search range : 1. Open the Search for... menu. 2. Select Edit Service, then select the service search range you want to assign the Quick Key to. 3. Select Search with Scan, then select Set Quick Key. 4. Enter the Quick Key you want to use for this search range. To a custom search range : 1. Open the Search for... menu. 2. Select Edit Custom, then select the custom search range you want to assign the Quick Key to. 3. Select Search with Scan, then select Set Quick Key. 4. Enter the Quick Key you want to use for this custom search range. Assigning a GQK All channels in the channel group will be enabled (or disabled) when you enter the GQK. Multiple channel groups in the same system can share the same GQK. However, all of these channel groups will be enabled (or disabled) when you enter the GQK from within that system. You can assign GQKs to channel groups even if their system does not have an assigned SQK. You can only use GQKs within the current system: the GQK will not affect a channel group in another system. GQKs range from 0 to 9 . 1. Open the Program System menu. 2. Select the system containing the channel group you want to assign the Quick Key to. 3. Select Edit Group, then select the channel group you want. 4. Select Set Quick Key, then enter the Quick Key you want to use for this channel group. Using Quick Keys Quick Keys only work in Scan mode. Entering the Quick Key toggles the enabled/disabled state of the system/site/search range or channel group (i.e., if the system is currently enabled, entering the Quick Key will disable it, and vice-versa). To use SQK 0 through 9 Enter Scan mode. Tap the number key that matches the SQK. (For example, if the SQK is 4, just enter 4.) Any systems, sites, or search ranges assigned to this SQK become disabled. (If they were already disabled, they become enabled.) To use SQK 10 through 99 Enter Scan mode. Tap the decimal point ( ./NO ), then enter the SQK. (For example, if the SQK is 32 , enter ./NO / 32.) Any systems, sites, or search ranges assigned to this SQK become disabled. (If they were already disabled, they become enabled.) To use a GQK Enter Scan mode. Go to the system that contains the channel group you want to enable or disable. Tap FUNCTION , then tap the number key that matches the GQK. (For example, if the GQK is 7 , enter FUNCTION / 7.) Any channel groups assigned to this GQK within the current system only become disabled. (If they were already disabled, they become enabled.) Programming Search Keys 1. Open the Search for... menu. 2. Select Set Search Key, then select the search key you want to program. 3. Select the search range you want to assign to this Search Key. Choose one of the pre-programmed service search ranges, one of the 10 custom search ranges, a Tone-Out search, or a Band Scope search. Using Search Keys To start the search assigned to a Search Key, FUNCTION + tap that Search Key. For example, to start the search assigned to Search Key 2, FUNCTION + tap 2 . (You can't use the Search Keys when the scanner is in Scan mode or GPS mode.) If the Search Key you select starts a Tone-Out search, the scanner switches to Tone-Out mode and searches the most-recently-used Tone-Out channel (out of the 10 available). If you want to search a different Tone-Out channel, use the SELECT-VOLUMESQUELCH knob on handheld models or the SCROLL / FUNCTIONknob on mobile models to select the Tone-Out channel you want to use To use Location-based Scanning with a particular system, you will need to program your scanner with the geographic coordinates you want to use for each site or channel group. You can also program your scanner to alert you when you approach particular locations. Programming a location for a site Programming a location for a channel group Programming general locations o To create a new location o For Dangerous Xing and Dangerous Roads only o Edit an existing location Programming a location for a site Each system site can have separate location information. 1. Open the Program System menu. 2. Select the system you want to program for location based scanning. 3. Select Edit Site, then select the first site you want to assign a location to. 4. Select the Set LocationInfo menu and enter the latitude, longitude, and range for this site. 5. Change the Set GPS Enable field to On . 6. Go back to the Edit Site menu and repeat these steps with any other sites you want to program for this system. Programming a location for a channel group Each channel group in a system can have separate location information. 1. Open the Program System menu. 2. Select the system you want to program for location based scanning. 3. Select Edit Group, then select the first channel group you want to assign a location to. 4. Select the Set LocationInfo menu and enter the latitude, longitude, and range for this site. 5. Change the Set GPS Enable field to On . 6. Go back to the Edit Group menu and repeat these steps with any other sites you want to program for this system. Remember: You have to turn on Set GPS Enable before the location information can effect that site or channel group. Programming general locations You can program general locations (i.e., locations that are not associated with a site or channel group). There are three types of general locations: points of interest ( POI ) intersections ( Dangerous Xing ) roads ( Dangerous Road ) You can program the scanner to alert you when you come within a designated distance of that location. To create a new location 1. Open the Program Location menu. 2. Select the type of location you want to create. 3. Select New Location to create a new location of this type. 4. *If you want to create a different type of location, go back to the Program Location menu and select that location type. 5. If you want to change the default location name, select Edit Name and enter a new name. 6. Select Set LocationInfo and enter the latitude and longitude for this location. 7. Select Set Range and enter the distance from this location you want the scanner to alert you. 8. Choose the Alert Tone and Alert Light you want the scanner to use when you come within range of this location. For Dangerous Xing and Dangerous Roads only In addition to range, you can specify a heading and a speed limit for these types of locations: If you set a speed limit, the scanner will only trigger an alert when you are within the location's range and your current speed is over the programmed speed limit. If you set a heading, the scanner will only trigger an alert when you are within the location's range and your current heading is +/- 45 degrees from the programmed heading. (For example, if you set the heading as North , the scanner will trigger an alert if your current heading is North-east but not if your current heading is due East .) Edit an existing location 1. Open the Program Location menu. 2. Select the type of location you want to edit; the scanner lists the existing locations of that type in alphabetical order. 3. Select the location you want to edit, then change any of the location settings you want. Your scanner can trigger alerts for several different events. The table below shows the different alerts and how to program them: To sound an alert when Follow these steps A channel becomes active Edit the channel properties (Edit Channel#Set Alert): 1. Go to the Program System menu and select the system that contains the channel you want set the alert for. 2. Select Edit Group , then select the group you want. 3. Select Edit Channel, then select the channel you want to set the alert for. 4. Select Set Alert . 5. Choose the Alert Tone and Alert Light you want the scanner to use. An active Talk Group on a system contains an emergency flag Edit the system properties (Edit Sys Option#Emergency Alert): 1. Go to the Program System menu and select the system you want set the alert for. 2. Select Edit Sys Option, then select Emergency Alert . 3. Choose the Alert Tone and Alert Light you want the scanner to use. The scanner detects a Close Call hit Edit the Close Call properties: 1. Go to the Close Call menu. 2. Select Set CC Alert . 3. Choose the Alert Tone and Alert Light you want the scanner to use. 4. For Close Call Alerts, you can also have the scanner pause before it resumes searching. Select Set CC Pause to activate this feature. The scanner gets a hit on Edit the Tone-Out channel properties: a Tone-Out channel 1. Go to the Tone-Out for... menu. 2. Select Tone-Out Setup , then select the Tone-Out channel you want to set the alert for. 3. Select Set Alert . 4. Choose the Alert Tone and Alert Light you want the scanner to use. You approach a particular location Point of Interest( POI ) Dangerous Road Dangerous Intersection ( Dangerous Xing ) Edit the location properties: 1. Go to the Program Location menu and select the type of location you want set the alert for. 2. Select the particular location. 3. For a POI, select Set Alert , then choose the Alert Tone and the Alert Light you want to use. 4. For a Dangerous Road or Xing, the alert tone is preset. Select the Alert Volume and the Alert Light you want to use Initializing Memory Follow these steps to initialize the scanner's memory: 1. Turn off the scanner. 2. Simultaneously press 2, 9, and HOLD. 3. While continuing to press these buttons, turn on the scanner. The scanner displays "All Memory Clear / Please Wait" for about 20 seconds while the memory is cleared. Then, the scanner displays "Restore Preprogram List? / Yes="E" / No="." " To restore the factory preset programming, press "E", otherwise, to leave the memory cleared press ".". The BCT15X comes preprogrammed with many of the channels used by local police, department of transportation, and highway patrol agencies, organized by state. You can also assign a state to the systems you program so that they can be included in State-byState scanning. Selecting your State To select your state, tap FUNCTION (the scroll knob) then tap the Volume control. Rotate the scroll knob to select your state, then press E to make your selection. The scanner unlocks any systems you have set to the selected state, locks out systems that are set to a different state, and uses the current state preprogrammed data during state-by-state scanning. Using the Built-In State-by-State Agencies To use the built-in State-by-State agencies, repeatedly tap DOT/POL/PRI and (Bear Paw)/HP/ALT until the desired agency type's icon shows in the bottom row of the display: PL -- Local Police DT -- Department of Transportation HP -- Highway Patrol BT -- BearTracker Warning System BearTracker Warning System The BearTracker Warning System (BWS) alerts you to nearby public safety radio activity. This can give you an advanced warning of police activity and other hazards when you are driving. The earliest BWS implementations primarily monitored for the frequencies used by mobile radio extenders -- radio units installed in patrol cars that extended the range of the officer's handheld radio. BWS has been extended to now include the "input" frequencies used by public safety agencies in your state. These frequencies are typically only receivable when you are up to 2 miles from the unit transmitting. Because the frequencies used vary from location to location, we've set up the scanner so that all you need to do is select what state you are in. From that point, BWS will use frequencies most often used in your state to alert you to nearby activity. Selecting your State To select the frequencies for your state, tap FUNC (the scroll knob) then the Volume knob. Use the scroll knob to select your state or Canadian province, then press E (or tap the scroll knob) to use your selection. Turning on the BearTracker Warning System To turn on the BearTracker Warning System, repeatedly press the (Bear Paw)/HP/ALT button until BT is displayed in the bottom line in the display. When BWS is turned on, you will notice received audio cutting out about every 2 seconds as the scanner checks for public safety radio activity. If the scanner detects such activity, it alerts you using the alert you set in the Set Bear Tracker menus. Muting BearTracker Alerts To temporarily mute BWS alerts, tap the Squelch knob during an alert. Alerts will be muted until you tap Squelch again The different shortcut keys have different functions. For more details about each, click the heading. Quick Keys Quick keys let you enable and disable systems and channel groups (disabled systems and channel groups are ignored during scans). You must be in Scan mode to use Quick Keys. System Quick Keys (SQKs) let you enable or disable systems, sites or search ranges: just enter the SQK from the number pad. For two-digit SQKs, first press ./no then enter the twodigit SQK number. Group Quick Keys (GQKs) let you enable or disable channel groups inside the current system: Tap FUNCTION , then enter the GQK from the number pad. Startup Keys Startup Keys let you lock and unlock several systems, sites, and search ranges all at the same time. When you activate a Startup Key, the scanner unlocks all systems, sites, and search ranges that are assigned to that same Startup Key; the scanner also locks all systems, sites, and search ranges that are assigned to a different Startup Key. To activate a Startup Key, press & hold the number key while you power the scanner on. Search Keys Search Keys let you quickly start one of 3 programmed searches. To start the search assigned to a Search Key, FUNCTION + tap that Search KeyMicrosoft Word 2016 Microsoft Word 2016