User Guide for AMPAK models including: ZQ6-WL72917, ZQ6WL72917, wl72917, WL7297 AIoT Module, WL7297, AIoT Module, Module
AMPAK Technology Inc. WL72917 AIoT Module ZQ6-WL72917 ZQ6WL72917 wl72917
File Info : application/pdf, 12 Pages, 503.34KB
DocumentDocumentWL72917 V00 User guide Brand: AMPAK Technology Inc Model: WL72917 Pin Descriptions NO Name Type Description 1 GND 2 EXT_RF_ANT 3 GND 4 GPIO_27 5 GPIO_25 6 GPIO_26 7 GPIO_10 8 GPIO_12 9 GPIO_11 10 GPIO_46 11 GPIO_51 12 GPIO_50 13 GPIO_49 14 GPIO_47 15 GPIO_48 16 UULP_VBAT_GPIO_0 17 GND 18 PA2G_AVDD 19 GND 20 JTAG_TMS_SWDIO 21 JTAG_TDO_SWO 22 JTAG_TCK_SWCLK 23 JTAG_TDI 24 ULP_GPIO_11 P Ground RF External RF Antenna I/O Interface P Ground I/O Refer to GPIO Muxing Tables for Released configuration; Option 2: SPI_MOSI I/O Refer to GPIO Muxing Tables for Released configuration; Option 2: SPI_SCLK I/O Refer to GPIO Muxing Tables for Released configuration; Option 2: SPI_CS I/O Refer to GPIO Muxing Tables for Released configuration I/O Refer to GPIO Muxing Tables for Released configuration I/O Refer to GPIO Muxing Tables for Released configuration I/O Refer to GPIO Muxing Tables for Released configuration I/O Refer to GPIO Muxing Tables for Released configuration I/O Refer to GPIO Muxing Tables for Released configuration I/O Refer to GPIO Muxing Tables for Released configuration I/O Refer to GPIO Muxing Tables for Released configuration I/O Refer to GPIO Muxing Tables for Released configuration I/O Ultra-low power mode and also in the retention and deep sleep mode of operation P Ground P Power supply for the 2.4 GHz RF Power Amplifier : 3.3V only P Ground I/O JTAG interface Test Mode Select signal. Bi-directional data pin for SWD Interface. O JTAG interface output data. Serial wire output for SWD Interface. (This pin can also be used as ISP_ENABLE. Pull down to enable ISP mode.) I/O JTAG interface clock or serial wire clock. I JTAG interface input data. I/O Refer to GPIO Muxing Tables for Released configuration Pin Descriptions NO Name Type Description 25 ULP_GPIO_7 I/O Refer to GPIO Muxing Tables for Released configuration 26 GPIO_8 I/O Refer to GPIO Muxing Tables for Released configuration; Option 1: UART_RX 27 GPIO_7 I/O Refer to GPIO Muxing Tables for Released configuration 28 GPIO_9 I/O Refer to GPIO Muxing Tables for Released configuration; Option 1: UART_TX 29 GPIO_6 I/O Refer to GPIO Muxing Tables for Released configuration 30 ULP_GPIO_6 I/O Refer to GPIO Muxing Tables for Released configuration 31 ULP_GPIO_10 I/O Refer to GPIO Muxing Tables for Released configuration 32 GND P Ground 33 POC_IN I Power On Control (POC) input. The POC_IN and RESET_N signals can be controlled from external source like R/C circuits and or another MCU's 34 RESET_N I Active-low reset asynchronous reset signal 35 ULP_GPIO_1 I/O Refer to GPIO Muxing Tables for Released configuration 36 ULP_GPIO_9 I/O Refer to GPIO Muxing Tables for Released configuration 37 UULP_VBAT_GPIO_3 I/O Ultra-low power mode and also in the retention and deep sleep mode of operation 38 UULP_VBAT_GPIO_2 I/O Ultra-low power mode and also in the retention and deep sleep mode of operation 39 UULP_VBAT_GPIO_1 I/O Ultra-low power mode and also in the retention and deep sleep mode of operation 40 GND P Ground 41 IO_VDD P I/O Power supplies for GPIOs. Always-on VBATT supply to the UULP GPIO Domains. 42 GND P Ground 43 VBAT 44 VBAT P Always-on VBATT Power supply to the RF. Power supply for the on-module Internal P DC Buck. Power supply for Internal 1.8V LDO Input Power. 45 GND P Ground 46 GND P Ground Pin Descriptions NO Name Type Description 47 ULP_GPIO_8 I/O Refer to GPIO Muxing Tables for Released configuration 48 ULP_GPIO_2 I/O Refer to GPIO Muxing Tables for Released configuration 49 GPIO_53 I/O Refer to GPIO Muxing Tables for Released configuration 50 GPIO_52 I/O Refer to GPIO Muxing Tables for Released configuration 51 GPIO_54 I/O Refer to GPIO Muxing Tables for Released configuration 52 GPIO_55 I/O Refer to GPIO Muxing Tables for Released configuration 53 GPIO_56 I/O Refer to GPIO Muxing Tables for Released configuration 54 GPIO_15 I/O Refer to GPIO Muxing Tables for Released configuration 55 GPIO_30 I/O Refer to GPIO Muxing Tables for Released configuration 56 GPIO_29 I/O Refer to GPIO Muxing Tables for Released configuration 57 GPIO_28 I/O Refer to GPIO Muxing Tables for Released configuration; Option 2: SPI_MISO 58 GPIO_57 I/O Refer to GPIO Muxing Tables for Released configuration 59 GND P Ground 60 GND P Ground 61 GND P Ground U4 J15 J12 J11 Test Board Function J16 J9 J14 SW1 SW2 1. U4 : WL72917_8M Module 2. SW1 : Power On Control(POC) Button 3. SW2 : Reset Button 4. J11 : JTAG Interface 5.J1 : Type C USB 6.J12 : In-System Programming(ISP) Enable 7.J9, J14, J15 & J16 : Module I/O Pin J1 J-Link Download Connection If the cable do not match, you can use a cable dupont connection. RF connection The EVK provides SMA antenna connectors , external RFout and I-PEX connector. If user wants to connect the I-PEX connector, need to put on C26 but C29 off. Looks like left of figure. Ant List Antenna Number Antenna 1 Antenna 2 Antenna 3 Antenna 4 Antenna 5 Antenna 6 Antenna 7 Antenna 8 Brand Name SparkLAN SparkLAN SparkLAN SparkLAN SparkLAN Pulse Pulse TSKY Warning Model Name AD-305N AD-103AG AD-301N AD-302N AD-303N TZ2412W ANT8010LL04R2400A A8-A006-00XXX Peak Gain 5 2.02 4.4 3.14 3.14 3.60 0.7 1.02 Type Dipole Dipole Dipole Dipole Dipole Dipole Chip PIFA Warning Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning IMPORTANT NOTE: This module is intended for OEM integrator. This module is only FCC authorized for the specific rule parts listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. Additional testing and certification may be necessary when multiple modules are used. OEM integrators that they must use the equivalent antennas or C2PC will be required. This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. The host manufacturer should reference KDB Publication 996369 D04 Module Integration Guide. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: ZQ6-WL72917 ". This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil contient des émetteurs / récepteurs exempts de licence qui sont conformes au (x) RSS (s) exemptés de licence d'Innovation, Sciences et Développement économique Canada. L'opération est soumise aux deux conditions suivantes: (1) Cet appareil ne doit pas provoquer d'interférences. (2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un fonctionnement indésirable de l'appareil. This radio transmitter [11956A-WL72917] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le présent émetteur radio (11956A-WL72917) a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal d'antenne. Les types d'antennes non inclus dans cette liste qui ont un gain supérieur au gain maximal indiqué pour tout type listé sont strictement interdits pour une utilisation avec cet appareil. Warning IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. OEM integrators that they must use the equivalent antennas or C2PC will be required. The distance greater than 20 cm has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the IC RSS-102 radiation exposure limits set forth for a population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep greater than 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains IC: 11956A-WL72917 ". The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online.Microsoft Word 2019