Instruction Manual for VEVOR models including: SH-004-BK, SH-004-BL-A, SH-002-BL-A, SH-002-RD, SH-002-SY, SH-004-BK Series Drum Set, SH-004-BK Series, Drum Set
DRUM SET MODEL:SH-004-BK, SH-004-BL-A, SH-002-BL-A,SH-002-RD, SH-002-SY DRUM SET MODEL: SH-004-BK, SH-004-BL-A, SH-002-BL-A,SH-002-RD, SH-002-SY This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product. -1- Parts list 8 "* 4" drum * 1, 8 "* 4" military drum * 1 6 "* 4" drum * 1 10 "* 8" floor standing drum * 1 14 "* 10" ground drum * 1 10 "pressure ring * 2 14 "pressure ring * 2 10 "drum face * 2 14 "drum face * 2 Drum stool * 1 set 10 "suspension wiping * 1 8 "step wipe * 2 Children's drumsticks * 2 Adult drumsticks * 2 Step hammer * 1 set Step on the bracket * 1 10 "cymbal pole * 1 Drum hook * 12 M6 * 140 screws * 12 M6 * 90 screws * 8 Gu Er Fang Mu * 2 1 set of military drum stand Ground drum legs * 2 Drumming legs * 3 Drum stand * 1 -2- 1-8: Lift the drumhead and place it on the drum shell, getting ready for installation. Install the tension adjustment components of the drum (such as square head screws), and use a tool (drum key) to initially tighten them evenly (tighten evenly) to fix the drumhead. Repeat the above operation to install and adjust the other side of the drumhead, ensuring that the tension of both drumheads is uniform and appropriate. -3- 9: Install the stand components for the tom-toms and fix them at the appropriate position on the bass drum or drum set to support the tom-toms. 10: Install the tom-toms onto the stand, adjust its position and Angle to facilitate playing. 11-14: Pick up the cymbal mounting component and install the cymbal onto the corresponding bracket, paying attention to the installation direction. Adjust the cymbal stand to ensure that the cymbal is in the right and stable position. Fine-tuning can be done through adjusting screws and other components. 15-16: Expand the support feet of the drum frame, erect the columns, install the adjusting components and fix them to stabilize the drum frame.Further adjust the drum frame components to ensure their stability and get ready for the placement of drums or other accessories. 18-24: Unfold the hi-hat stand and fix it by tightening the screws. Insert the main pole of the hi-hat stand into the corresponding interface of the base. Install the hi-hat tray and other components at the appropriate position on the main pole. Prepare the washers, screws and other components needed for installing the hi-hat in sequence. Place the hi-hat on the tray and then fix it with the prepared components. Check again to ensure the hi-hat is installed firmly. Adjust the hi-hat stand to the appropriate height and angle. -4- 25-29: Unfold the drum stool stand and make sure the legs are firmly extended. Pick up the extension rods and other components of the drum stand to prepare for further assembly. Connect and fix the extension rods and other components to the main pole of the drum stand. Tighten the screws and other fastening parts at the connection points to ensure a tight connection. Install the drum stool at the appropriate position on the drum stand to complete the installation of the drum set. -5- Manufacturer: Tianjin Korpus Musical Instrument Co., Ltd Address: 50 meters east of Cierzhuang Primary School, Tangguantun Town, Jinghai District, Tianjin City, China Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 UK EC REP REP YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX E-CrossStu GmbH Mainzer Landstr.69, 60329 Frankfurt am Main. -6-WPS 文字