AMP Research Accessories | RealTruckRealTruck Warranty Registration | RealTruck
Installation Guide for AMP RESEARCH models including: 76138-01A Running Board Assembly, 76138-01A, Running Board Assembly, Board Assembly
File Info : application/pdf, 18 Pages, 3.59MB
DocumentDocumentINSTALLATION GUIDE TM ® APPLICATION Dodge Ram Regular Cab * Dodge Ram Quad Cab * Dodge Ram Crew Cab Dodge Ram Regular Cab * Dodge Ram Crew Cab Dodge Ram Mega Cab 1500 1500 1500 2500/3500 2500/3500 2500/3500 MODEL YR 2013 - 2015 2013 - 2015 2013 - 2015 2013 - 2015 2013 - 2015 2013 - 2015 *Modification required to running board assembly. See Item 1 on page 3. NOTE: EXCLUDES CHASSIS CAB MODELS WITH DIESEL ENGINES. PART # 76138-01A 76138-01A 76138-01A 76138-01A 76138-01A 76138-01A REV B REV B REV B REV B REV B REV B INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 123 4 4= Experienced TOOLS REQUIRED q Safety goggles q Measuring tape q 13mm wrench q 19mm wrench q 13mm socket q 10mm socket q Ratchet wrench and extension q Wire stripper / cutter q 3/16" hex key (allen wrench) q 4mm hex key (allen wrench) q Rivet Tool q 1/8", 9/32" and 3/16" Drill Bit q T27 torx Bit q Center Punch q Anti Corrosion Paint q Electrical tape WARRANTY 5-Year Limited Warranty AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2) Monday - Friday, 7:00 AM - 5:00 PM PST Invented, engineered and manufactured exclusively by AMP Research in the USA. May be covered by one OR MORE of the following patents: 6,641,158; 6,830,257; 6,834,875; 6,938,909; 7,055,839; 7,380,807; 7,413,204; 7,398,985; 7,584,975; 7,566,064; 7,487,986; 8,157,277; 8,408,571; 9,302,626; 9,561,751; 10,053,017; CA2463717 ©2012 AMP Research. All rights reserved. Printed in USA. www.amp-research.com 1/16 IM76138 rev 1.25.23 AMP RESEARCH POWERSTEPTM DODGE RAM INSTALLATION GUIDE Motor to linkage assembly NOTE: The motors will be attached on step 27 (page 14). EXPLODED VIEW · Motor kit · Socket cap screws · Motor Linkage assembly www.amp-research.com CAUTION: HANDLE WITH CARE. To ensure our customers receive all components with full integrity, we pack the motors separate from their linkage assemblies. This requires that the installer position and fasten the motor before continuing with the install. Please follow the instructions below and handle the assembly carefully. CAUTION: Dropping the assembly or any excessive impact MAY cause damage to the motor. Instructions: 1. Position the gear cover in place as shown if not already in place. 2. Seat motor into position on the three mounting bosses. This may require an adjustment of the gear by moving the swing arms. 3. After seating into place, fasten the motor with the three motor mount screws with 4mm Hex Head. Tighten screws to 36 in-lbs (4N-m). Do not over torque. 2/16 IM76138 rev 1.25.23 AMP RESEARCH POWERSTEPTM DODGE RAM PARTS LIST AND HARDWARE IDENTIFICATION Note: Some Applications require modification. Application Crew Cab, Mega Cab Cut Length 79" (No Modification Required) Quad Cab 72" (Trim 7") Regular Cab 50" (Trim 29") 1 x2 Running Board Assembly - End caps (1 left & 1 right) - T-Nut Insert (x2) - S-style clips (x2) Driver Side Linkages 2 Motor Linkage Assembly - Driver Side 3 Idler Linkage Assembly - Driver Side Passenger Side Linkages 4 Idler Linkage Assembly - Passenger Side 5 Motor Linkage Assembly - Passenger Side www.amp-research.com 3/16 IM76138 rev 1.25.23 AMP RESEARCH POWERSTEPTM DODGE RAM PARTS LIST AND HARDWARE IDENTIFICATION 6 Wire Harness 7 STA Controller 8 x8 Rivet Nut 9 Rivet Nut Tool 10 x20 Conicle Washer Bolt 11 x8 Blind Rivet 12 x8 Socket Cap Screw 13 x20 Cable Tie (7") 14 x2 Cable Tie (11") 15 x2 Posi-LockTM Connector 16 x8 Button Head Torx Screw 17 x8 Washer 18 x4 19 x4 Grommet LED Lamp www.amp-research.com 20 x8 Butt Connector 4/16 21 x4 Reinforcement Bracket IM76138 rev 1.25.23 AMP RESEARCH POWERSTEPTM DODGE RAM 22 x4 Blind Rivet 23 OBD II Plug 24 x2 Spacer (front drive linkage) 25 x2 Motor kit 26 x2 Front Body Mount FOR 1500 MODELS ONLY! 27 x2 Rear Body Mount 28 29 Short Hex Bolt Large Washer 30 Nylock Nut 31 Bracket www.amp-research.com 5/16 32 Harness Relocation Bracket IM76138 rev 1.25.23 AMP RESEARCH POWERSTEPTM DODGE RAM NOTE: 1500 RAM Only! Powerstep installations require additional steps and come with the required additional hardware. Please read and carefully follow the instructions in Step 1 for your vehicle model. Follow Steps 1-5 to relocate brake cable and wire harness plug and then proceed with the Power Step installation. For Ram 2500/3500 Skip to step 6. 1500 RAM ONLY. On Drivers side of vehicle towards front of body remove harness bracket with 10mm socket or wrench. Remove plug from bracket. And replace with supplied bracket (32) using two of the three factory screws. 1 1500 RAM ONLY. While holding brake cable adjustment nut with wrench (located on driverside along frame, towards the rear), loosen brake cable to allow for slack. Mark position of nut before loosening. 1500 RAM ONLY. After gaining enough slack, detach brake cable as shown below. This detachment point is located just to the rear of the adjustment nut. 2 13mm 1500 RAM ONLY. Remove brake cable guide from frame by depressing locking tabs and sliding guide out through hole. Unthread brake cable from frame mount. 3 1500 RAM ONLY. Attach brake cable guide to supplied Brake Cable Bracket (31) and mount bracket with supplied hardware. Reattach brake cable and readjust brake cable adjustment nut to 31 4 www.amp-research.com 5 6/16 28 30 29 13mm 13mm IM76138 rev 1.25.23 AMP RESEARCH POWERSTEPTM DODGE RAM HARDWARE MOUNTING OVERVIEW (passenger side shown) Locate forward most and rearward most mounting provisions on inner sill of truck. Remove tape from sill drain hole at both mounting points. Note: Some vehicles may have Front welded fasteners installed already. Backing plates and rivet nuts are not needed on these locations. Factory Rivet nuts will need to be removed to install backing plates Front Idler Assembly NOTE: Driving Linkage Assemblies (with motor) mount in the front; Idler Assemblies mount in the rear. 16 Driving Assembly Set Reinforcement Plate in place and locate with rivet nuts. Drill hole using an 1/8" drill bit. After drilling apply paint to prevent rusting Once hole is drilled insert a piece of string or wire through hole in Reinforcement Plate. Set plate into position. 21 21 27 Set rivet nuts into place for alignment. Insert pop rivet through hole in plate and secure in place. Once pop rivet is installed remove string or wire from Reinforcement Plate. NOTE: Verify plate is pulled flush to the body before securing pop rivet. 38 Assemble Hex Bolt (lubricated with soapy water), Washer, Rivet Tool, and Rivet Nut together as shown and place into hex cutouts in sill. An extra Hex Bolt and M8 Washer is supplied to install rivet nuts. 9 49 22 www.amp-research.com 150 7/16 8 IM76138 rev 1.25.23 AMP RESEARCH POWERSTEPTM DODGE RAM With Rivet Nut Tool held in place with 19mm wrench, tighten Hex Bolt until Rivet Nut deforms and secures itself to the sheet metal (110 in-Lbs. or 4 turns). Remove Hex Bolt and Rivet Nut Tool. Repeat for each of the four mentioned mounting locations. Once rivet nuts are in place use a screwdriver to push back tab in hole to avoid interference with linkage mount. WARNING: Rivet Nuts not properly collapsed will not hold securely to sheet metal. NOTE: Hold Rivet tool with wrench 11 while loosening bolt. 12 19mm 13mm Rear Linkage Install: Set rear body mount plate (27) to body. Note: Center and rear hole will be used. Driver side shown. Use supplied Conical washer bolts (9) to attach as shown, At the pinch weld Use a T27 Torx driver and torque bolts to 6ft-lbs. Next torque bolts to 16 ft-lbs. T27 13 Rear Idler linkage: Set linkage into position. Use supplied conical washer bolts to attach linkage to body mount plate. Use rear most bolt as shown on driver side. Passenger side will use rear mount position as well. Torque bolts to 16ft-lbs. 14 www.amp-research.com 8/16 IM76138 rev 1.25.23 AMP RESEARCH POWERSTEPTM DODGE RAM Set front body mount plate (26) to body.. Driver side shown. Use supplied Conical washer bolts to attach as shown, At the pinch weld Use a T27 Torx driver and torque bolts to 6ft-lbs. Next torque bolts to 16 ft-lbs. If crash bracket is not present use supplied spacer (24) in place of bracket. Spacer can be inserted after body mount is up into position. Spacer will be held in place by drilling and pop riveting into place. Rivets will be installed in step 39 & 40. 195 Front Drive Linkage: Use 3 of the supplied conical washer bolts (8) to attach linkage to body mount plate. Torque bolts to 16ft-lbs. 196 www.amp-research.com 9/16 IM76138 rev 1.25.23 AMP RESEARCH POWERSTEPTM DODGE RAM The jogs in the lower part of the linkages point toward one another, as shown, Drive (motor) Linkage in the Front and Idler Linkage in the Rear. Note: Linkage position described in parts list on page 3. 7 17 Install boards: Slide mounting T-Nut of board into position and attach to linkages. Shift board forward as much as possible for proper clearance. The end of board/end cap will nest into linkage lower mount 1/2" when positioned correctly. With boards in extended position step on boards to seat linkages. Walk the length of the board taking bouncing steps. DO NOT JUMP ON BOARD! Verify that board end caps do not contact the pinch weld. If Endcaps make contact loosen 4 button head screws at pinch weld. Walk the length of the board and apply weight to the center of the board and while applying weight retighten button head screws at pinch weld. Torque to 10 ft-lbs. (13.5 Nm) For instructions on how to adjust board due to pinchweld Interference, scan QR Code to watch video, or type the following link to 21382 your browser: https://youtu.be/ITbAeixVKdQ www.amp-research.com 10/16 IM76138 rev 1.25.23 AMP RESEARCH POWERSTEPTM DODGE RAM Prepare large tie-wraps for mounting Power Step Controller. Loosely loop tie-wraps around large bundle of wires behind battery in engine compartment. Insert controller into tie-wrap loops and cinch down securely. The tie-wraps should cinch down into channels on controller surface. 14 14 7 919 Remove fuse from Power Step Wire Harness. 20 Connect power leads from Controller, Red to positive battery terminal and Black to the vehicle body ground as shown. 6 6 21 Locate large rubber wire boot on driver side firewall as shown below. Slice small opening as shown below to run trigger wires through. 10mm 272 www.amp-research.com 25 11/16 IM76138 rev 1.25.23 Tape leading end of wires together and push through rubber boot to cabin side of the firewall. Silicon lubricant may be used for ease of passage. The trigger wires will come out just above and to the left of the brake pedal. 293 OBD II Connector located below driver side steering column. 212148 www.amp-research.com 12/16 IM76138 rev 1.25.23 AMP RESEARCH POWERSTEPTM DODGE RAM OBD II install: Use Supplied Posi Twist connectors to attach the Plug and Play Module to the Harness. Attach matching colors on the harness to the wires on the module. Plug in module to OBD II port on the vehicle. Secure harness with supplied tie wraps. Note: If the OBD II pass thru harness (76404-01A) was purchased see install sheet supplied in packaging. The pass through harness allows for an open port for other accessories. See below for a brief description. To Powerstep Motors To Vehicle Power (12V) Powerstep Control Module Vehicle Port Powerstep Connection Module Direct to Port Option To Vehicle Power (12V) To Powerstep Motors Powerstep Connection Module 1255 www.amp-research.com Powerstep Control Module Vehicle Port Pass-Through Harness Option Vehicle Port Pass-Through Harness (pin-topin at each terminal) New Vehicle Port (replaces original port) 13/16 IM76138 rev 1.25.23 AMP RESEARCH POWERSTEPTM DODGE RAM Route the two Wire Harness legs down over the wheel wells toward Motor Linkages, long leg across to the passenger side. Secure harness with tie wraps (13). Using a 4mm hex key torque bolts to 36 in-lbs. See page 2 for motor installation instructions. 4 286 On driver side, run Wire Harness leg down and along underside of the vehicle floor and frame to front Drive Linkage. Connect harness to motor and secure harness with tie wraps. Route remainder of wire harness towards rear linkage assembly for LED lights 2927 4 3208 29 On Passenger Side, run Wire Harness leg down and along underside of the vehicle floor and frame to front Drive Linkage. Connect harness to motor and secure harness with tie wraps. Route remainder of wire harness towards rear linkage assembly for LED lights 3229 www.amp-research.com 14/16 4 IM76138 rev 1.25.23 AMP RESEARCH POWERSTEPTM DODGE RAM On each side of the vehicle measure from the front edge of door line on the pinch weld to the specified lengths below. Measure at 22" for the front LED Light and 64-3/4" for the rear LED Light. Note for Quad cabs mount lights at 22" and 54" for Regular cabs mount lights at 10" and 45". Drill a 9/32" hole through the pinch weld at marked locations. Deburr all holes. After drilling apply paint to holes to prevent rusting 30 64-3/4" 22" Insert grommet into drilled holes. Insert lamp wires through the grommets. (Silicon lube will help wires slip through grommets.) 31 Affix lamp to rocker panel surface. Make sure lamp is affixed to a flat, clean surface. 1198 1189 19 18 32 Using supplied butt connectors, connect the lamp wires. Red to Red, Black to Black. Once Crimped use heat gun to shrink tube. 33 Close and wrap with conduit and electrical tape. Secure all loose wires with cable ties, with lamp wires pulled upward to avoid any wire snagging. 2200 34 www.amp-research.com 35 15/16 IM76138 rev 1.25.23 AMP RESEARCH POWERSTEPTM DODGE RAM With linkage resting square on the hex bolts Using 30a 3/16" Drill bit, drill both upper holes in linkage through sheetmetal. After drilling apply paint to holes to prevent rusting. Using a Rivet Gun install rivets. 36 3/16" 3337 Reinstall fuse to Powerstep harness. Check that all doors activate the Power Step and the LED Lights work when doors open and close. Reinstall any remaining trim panels. 46 FINAL SYSTEM CHECK Check that all doors activate the PowerStep and the LED lights work when doors open and close. NORMAL OPERATION: When the doors open, PowerStep automatically deploys from under the vehicle. When the doors are closed, PowerStep will automatically return to the stowed/retracted position. Note that CORRECT OPERATION OF LIGHTS: All four lamps will illuminate upon opening any door of vehicle. Lamps will stay on until restowing of both Power Steps or until 5 minutes has expired with the doors open. When the lights timeout after 5 minutes, they can be reillumintated by closing and opening any door of vehicle. 38 www.amp-research.com 16/16 IM76138 rev 1.25.23 TM AMERICAN DESIGNED, ENGINEERED AND MANUFACTURED. Thank you for your recent AMP Research Purchase. REGISTER YOUR PRODUCT TODAY FOR FASTER SERVICE & PRODUCT UPDATES Please visit: www.amp-research.com/productregistration or scan the QR Code Product Registration Benefits: · Ensure we have your purchase receipt and product info in our system which is required for warranty · Faster and easier access to customer service and tech support in the unlikely event you need warranty or product support · Registration helps us keep you up to date on product information and offers To view other Amp Research products that may be offered for your vehicle. Please visit: www.amp-research.com Rev 01.05.21 TM Congratulations on your purchase of the genuine AMP Research PowerStep! Here's what you should know... AMP Research PowerStep running boards automatically move when the doors are opened to assist entering and exiting the vehicle. Automatic power deploy: The running boards will extend down and out when the doors are opened. Automatic power stow: The running boards will return to the stowed position when the doors are closed. There will be a 2-second delay before the running boards move to the stowed position. Automatic stop: If an object is in the way of the moving running board, the running board will automatically stop. To reset, clear any obstruction, then simply open and close the door to resume normal operation. Manually set in the deployed (OUT) position for access to the roof: your foot while at the same time closing the door. To resume normal operation, open and close the door. Maintenance: In adverse conditions, debris such as mud, dirt, and salt may become trapped in the running board mechanism, possibly leading to unwanted noise. If this occurs, manually set the running boards to Avoid spraying the motors directly. After washing, apply silicone spray lubricant to the hinge pivot pins. Do not apply silicone, wax or protectants like Armor All® to the running board stepping surface. Caution! Keep hands away when the running board is in motion. 5-YEAR LIMITED WARRANTY AMP RESEARCH warrants this product to be free from defects in material and workmanship for FIVE (5) YEARS FROM DATE OF PURCHASE, provided there has been normal use and proper maintenance. This warranty applies to the original purchaser only. All remedies under this warranty are limited to the repair replacement of the product itself, or the repair or replacement of any component part thereof, found by the factory to be defective within the time period specified. The decision to repair or replace is wholly within the discretion of the manufacturer. for instructions. You must retain proof of purchase and submit a copy with any items returned for warranty work. Upon completion of warranty work, if any, we will return the repaired or replaced item or items to you freight prepaid. Damage to our products caused by accidents, fire, vandalism, negligence, misinstallation, misuse, Acts of God, or by defective parts not manufactured by us, is not covered under this warranty. ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE CREATED HEREBY ARE LIMITED IN DURATION TO THE SAME DURATION AND SCOPE AS THE EXPRESS WRITTEN WARRANTY. OUR COMPANY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. FOR WARRANTY ISSUES WITH THIS PRODUCT PLEASE CALL AMP RESEARCH TECH SUPPORT 1-888-983-2204 WARNING Be sure to read and precisely follow the provided instructions when installing this product. Failure to do so could place the vehicle occupants in a potentially dangerous situation. After installing or reinstalling, re-check to insure that the product is properly installed. The material that your product is made from can be recycled. Please also consider recycling the packaging that your product came in.