Automotive OEM integration | CRUX Interfacing Solutions
User Manual for CRUX models including: SWRTY-61N Wiring Interface, SWRTY-61N, Wiring Interface, Interface
Crux SWRTY-61N Wiring Interface Connect a new car stereo and retain the steering wheel audio controls and backup camera in 2012-19 Toyota vehicles at Crutchfield
File Info : application/pdf, 3 Pages, 1.23MB
DocumentDocumentINTERFACING SOLUTIONS R + RADIO REPLACEMENT SWC RETENTION SWRTY-61N Radio Replacement with Steering Wheel Retention and Rear-View Camera Retention for TOYOTA Vehicles PRODUCT FEATURES: - Retains factory features in select Toyota vehicles while functioning with an aftermarket radio. - Pre-programmed to retain factory Steering Wheel Controls. - iPhone Voice Recognition (VR) feature from SWC on select radios. - Retains OEM Rear View Camera. - Retains factory USB and auxiliary audio input (aftermarket radio must have these features). - Includes factory USB retention adapter cable. - Supports BT-HF/A2DP/AVRCP profile on select aftermarket radio models. - Supports Pick Up/End Call, Pick up and Toggle between 1st and 2nd incoming call, AVRCP Track, Seek. - EIA color coded wiring for easy installation. PARTS INCLUDED: SWRTY-61N MODULE INSTALLATION DIAGRAM: SWRTY-61N HARNESS USB Retention Cable SWC CABLE +12V Constant +12V ACC Ground Illumination Not Used Right Front (+) Right Front (-) Left Front (+) Left Front (-) Right Rear (+) Right Rear (-) Left Rear (+) Left Rear (-) Vehicle Speed Sense (VSS) Reverse Trigger Parking Brake (see special note below) Power Antenna Yellow Red Black Orange Blue/ White Gray Gray/Black White White/Black Violet Violet/Black Green Green/Black Red/Black Red/White Yellow/Black Blue Audio Input (Retains Factory AUX Input in Select 2007-Up Vehicles) Red/White RCA 24 PIN AFTERMARKET RADIO Yellow RCA (Retain OE Camera) Rear View Camera Signal 12-Pin Black Connector SWRTY-61N MODULE ON RADIO VEHICLE 1 2 3 4 5 6 7 8 USB-TY01 USB Retention Adaptor (included in kit) AFTERMARKET TOYOTA RADIO SELECTOR SWC SETTING (See Chart) (OFF ON OFF ON) ON RADIO VEHICLE 1 2 3 4 5 6 7 8 3.5MM SWC CABLE Plug in the 3.5MM SWC cable to the 4-pin port on the module. See "DIP SWITCH SETTINGS" section. Cap or insulate if not being used Kenwood/JVC (BLUE / YELLOW) To aftermarket radio SWC port Insulate with tape if not being used TO FACTORY HARNESS 28 PIN 10 PIN 6 PIN Blue / Antenna Turn On ANTENNA ADAPTOR (Included in Kit) Blue / Antenna Turn On NOTE: The BLUE Antenna Turn-On wire should ONLY be connected to one circuit of the aftermarket radio. Choose the one which has a wire populated on the factory connector side. 1 of 3 Crux Interfacing Solutions · Chatsworth, CA 91311 phone: (818) 609-9299 · fax: (818) 996-8188 · www.cruxinterfacing.com rev.021121 INTERFACING SOLUTIONS R + RADIO REPLACEMENT SWC RETENTION SWRTY-61N Radio Replacement with Steering Wheel Retention and Rear-View Camera Retention for TOYOTA Vehicles SPECIAL NOTE: On 2013 Toyota Sequoia and Tundra, the parking brake wire (RED wire) is in position#1 on the OEM 28-pin connector. Please insert the YELLOW/BLACK wire on the SWRTY-61N harness into position#1. For all other models, please insert into position# 15. Please check that you are inserting the pin into the correct location as it is difficult to remove it again. The locking tab of the pin should be facing UP when it is inserted into the connector. For 2013 Sequoia & Tundra Pin#1 Pin#15 SWRTY-61N 28-Pin Connector (wire view) For all other models DIP SWITCH SETTINGS: AFTERMARKET RADIO DIP SWITCH SETTINGS: RADIO BRAND: DIP: 1 2 3 4 Atoto, Dual, Farenheit, Jensen, Pioneer OFF OFF ON ON Power Acoustik, Soundstream OFF OFF ON ON Blaupunkt, Most off-brand Radios OFF OFF ON ON Alpine OFF OFF OFF OFF Clarion OFF ON ON OFF Kenwood OFF ON ON ON JVC OFF ON OFF ON Boss, Old Sony OFF ON OFF OFF New Sony OFF OFF ON OFF SWC MODULE ON RADIO VEHICLE 1 2 3 4 5 6 7 8 NOTE: For Atoto, Blaupunkt, Dual, Farenheit, Power Acoustik, Soundstream, and most off-brand radios, check the aftermarket radio's manual to see if the SWC buttons need to be programmed. TOYOTA STEERING WHEEL CONTROL DIP SWITCH SETTING: DIP: 5 6 Toyota OFF ON 7 8 OFF ON SWC MODULE ON RADIO VEHICLE 1 2 3 4 5 6 7 8 3.5MM SWC CABLE Plug in the 3.5MM to 4-Pin SWC cable to the SWC module. NOTE: Insulate the Blue/Yellow wire or the 3.5mm plug if not being used. For aftermarket radios that have wires for SWC connections, cut off the 3.5mm plug on the Crux SWC Cable and connect the SWC wires as follows: RED to SWC Key 1 WHITE to SWC Key 2 SHIELD to SWC Ground Note that there are some radios that only have SWC1 and SWC2, in this case "shield" does not need to be connected. 2 of 3 Crux Interfacing Solutions · Chatsworth, CA 91311 phone: (818) 609-9299 · fax: (818) 996-8188 · www.cruxinterfacing.com rev.021121 INTERFACING SOLUTIONS R + RADIO REPLACEMENT SWC RETENTION SWRTY-61N Radio Replacement with Steering Wheel Retention and Rear-View Camera Retention for TOYOTA Vehicles 24 TO 16 PIN ADAPTER: Some vehicles do not have the 24-Pin Video Input connector. Instead, they have a 16-Pin connector that controls the video input for the camera. Use the optional adaptor and connect to the T-harness to convert the harness to work with the 16-Pin connector style. TO SWC HARNESS TO FACTORY RADIO 24-PIN (male plug) 16-PIN (male plug) RED / PARKING BRAKE (Use instead of Yellow/Black Wire on Main Harness) VEHICLE APPLICATIONS: SCION 2012 - 2016 FRS 2016 iM 2012 - 2013 iQ 2012 - 2016 tC 2012 - 2015 xB 2012 xD **Note: See Special Note on page 2. TOYOTA 2012 - 2019 2012 - 2018 2012 - 2017 2012 - 2017 2013 - 2018 2012 2012 - 2017 2012 - 2018 2012 - 2018 2015 - 2017 2013 - 2019 2013 - 2019 2012 - 2015 4Runner Avalon Camry Corolla Highlander Matrix Prius RAV4 Sequoia** Sienna Tacoma Tundra** Venza 3 of 3 Crux Interfacing Solutions · Chatsworth, CA 91311 phone: (818) 609-9299 · fax: (818) 996-8188 · www.cruxinterfacing.com rev.021121