User Manual for REYEE models including: E3, 2AX5J-E3, 2AX5JE3, RG-E3 Wi-Fi 6 AX1800 Smart Wi-Fi Mesh Router, Wi-Fi Mesh Router, AX1800, Mesh Router
Ruijie Networks Co., Ltd. E3 1800M Wi-Fi 6 Dual-band Mesh Router 2AX5J-E3 2AX5JE3 e3
Press the Reyee Mesh button on the first router. Press the Reyee Mesh button on the first router, and its indicator will blink in green during ssearching for routers. The ... Reyee RG-E3 Wireless Router User Manual Scan to Download Reyee Router App Name Quantity Unit Router 1 Set Power Adapter 1 Piece Warranty Card 1 Copy User Manual 1 Copy
Reyee RG-E3 Wireless Router User Manual Packing List Name Router Power Adapter Warranty Card User Manual Network Cable Appearance Quantity 1 1 1 1 1 Unit Set Piece Copy Copy Piece Reyee Mesh Indicator System Status Indicator Power LAN 1-4 Ports WAN Port Reset Button Please connect the power and network cables as shown below. Scan to Download Reyee Router App ISP Broadband WAN Port (Yellow) Indicator Reyee Mesh Indicator System Status Indicator Reyee Mesh Indicator Blinking The device is being paired. Green Steady on The device is paired and Wi-Fi signal is normal. Orange Steady on The device is paired but Wi-Fi signal is weak. Red Steady on The device pairing is disconnected. System Status Indicator Steady on The device is running normally. Blue Blinking Restoring the factory settings or restarting. Network Connection Scenario 1: Configure a single router After you connect the cable and power the router on, it will start up in 2 to 3 minutes. Wait until the system status indicator turns into steady blue and the router broadcasts the SSID (@Reyee -sXXXX by default). Access the Internet by Web browser Wi-Fi @Reyee-sXXXX xxxxx-xxxxxxxx xxxxx-xxxxxxxx xxxxx-xxxxxxxx S/N:GXXXXXXXXXXXX MAC:XXXX XXXX XXXX MAC:XXXX XXXX XXXX (XXXX refers to the last four digits of MAC on the back of router) Connect to the SSID @Reyee-sXXXX, and the configuration page will be displayed automatically; if not, please visit 192.168.110.1. @Reyee-sXXXX The router will match the Internet access method. Please configure the network parameters accordingly. Configure the SSID and password. After the configuration working, you can connect to the SSID and access to the Internet. Access the Internet by App Download the Reyee Router App Register an account by one click Login/Register Tap Add Router and follow the guide for configuration Add Router Scenario 2: Reyee Mesh Place the second router within 2 meters of the first one, and power it on. After the system status indicator blinks in blue, wait for 2 to 3 minutes until it turns into steady blue. (If the router had been configured before, please press the Reset Button for more than 3 seconds to restore the factory settings) Press the Reyee Mesh button on the first router. Press the Reyee Mesh button on the first router, and its indicator will blink in green during searching for routers. The indicator on the second router will also blink in green slowly during pairing . After 2 minutes, as the indicators on both routers turn into steady green, the pairing succeeds. Press the Reyee Button (All devices within 2 meters) 2 1 Modem Don't need to press Reyee Mesh button on the second router Place the second router to the specified position and power it on. After powering the router, wait for 3 to 5 minutes until the Reyee Mesh indicator turns into steady blue, it is all set and you can access the Internet. The meshed routers will share the same SSID and password. Visit 192.168.110.1 to check router connecting condition. If there is any network port available, you can connect cables as shown below. The wired connection is more stable. 1 2 LAN Internet WAN Please note that Wi-Fi signal may be weak if two routers are placed far from each other or there are several obstacles like walls between them. The Internet speed may be slow if there are multiple paired routers. We recommended mesh-up within 5 routers (1+4) to keep good performance. FAQs What to do if I forget the management password? Try the Wi-Fi password which may be the same with the management password. If not, please restore the factory settings. How to restore the factory settings? Power on the router and wait for 2 to 3 minutes until it starts up. Press the Reset button for more than 3 seconds until the system status indicator blinks. After the indicator changes to steady on and the SSID "@ Reyee-sXXXX" is broadcast, the router restores the factory settings successfully. Can I connect multiple routers with network cables? Yes, and wired connection is more stable. You can connect the WAN port (yellow) from secondary device with the LAN port (black) from master router for wired connection. Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Statement: This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. RF Exposure Warning! This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IMPORTANT! Operation in the band 5150-5250 MHz is only for indoor use Innovation,Science and Economic Development Canada Statement This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage; (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Exposure Statement The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de RSS - 102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf. RF Exposure Warning! This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps. 5G UNII-1 Statement 1.The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; 2.DFS (Dynamic Frequency Selection) products that operate in the bands 5250-5350 MHz, 5470-5600MHz, and 5650-5725MHz. 1.Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; 2.Les produits utilisant la technique d'atténuation DFS (sélection dynamique des fréquences) sur les bandes 5250- 5350 MHz, 5470-5600MHz et 5650-5725MHz.Corel PDF Engine Version 18.1.0.661