Instructions for 86mm size receiver system

I. Features

• Built-in silver screen printing button, beautiful and lasting.
• Anti-scratches acrylic surface, built-in lamp light guide, soft and well-distributed.
• Roast piano lacquer frame, noble and elegant.
• Shock-proof TV5 relays.
• SMT machine automatic assembly in damp-proof enclosure.

▲ Installation Note

Besides the Standard of Electric Safety, please follow:

• Do not install the receiver in or too close to any metallic parts or it will affect the receive distance.
• Effective signal distance: 80m in open area.
• Minimum distance between the Receiver and the floor: 1.5m.
• Minimum distance between the Receiver and the roof: 0.3m.
• Minimum distance between the Receiver and the transmitter: 0.2m.
• Make sure the power has been cut off before wiring to ensure safety.
• Avoid static disturbance which could damage electronic components.
• Use flexible cables.
• Ensure no longitudinal force is acting on cables after installation.

II. Parameter

III. Installation and wiring

Diagram 1: AC227-01 Single route radio receiver

Illustrates AC power input connecting to the receiver, and the receiver output connecting to a motor.

Diagram 2: AC228-01 Double route radio receiver

Illustrates AC power input connecting to the receiver, and the receiver output connecting to Motor 1 and Motor 2.

Diagram 3: Wiring terminals

AC227-01 Single route radio receiver terminals:

• AC input: L (Live), N (Neutral), E (Earth/Ground)
• Motor output: L, N

AC228-01 Double routes radio receiver terminals:

• AC input: L (Live), N (Neutral), E (Earth/Ground)
• Motor 1 output: L, N
• Motor 2 output: L, N

IV. Product diagram

The product diagram shows receivers with indicator lights for setting, and UP, STOP, DOWN buttons. The AC123 transmitter is depicted with UP, STOP, DOWN, RIGHT, LEFT, PROG buttons and a screen, along with indicator lights.

V. Installation instruction

General Notes:

• 5 minutes is the longest operation time for the motor.
• 0.5 seconds is the transfer time for up/down for the motor.
• The same adjustment method is used for single route and double route receivers.
• If the transmitter is multi-channel, please choose the correct channel first.

1. Programming

1. Press the "STOP" button on the receiver for 5 seconds. The indicator light flashes quickly 3 times.
2. Press the "UP" button on the transmitter within 10 seconds. The receiver is programmed.

2. Direction Conversion

If the motor operates in the correct direction, no conversion is needed. If not, follow these steps:

1. Press the "UP + DOWN" button on the receiver for 5 seconds. The indicator light flashes quickly 3 times.
2. Press the "UP" button on the transmitter within 10 seconds. The direction is transferred.

3. Dot-moving and Continuous-moving Transfer

Method 1:

1. Press the "STOP" button on the receiver for 5 seconds. The indicator light flashes quickly 3 times.
2. Press the "STOP" button on the transmitter within 10 seconds. The setting is transferred.

Method 2:

1. Press the "UP + STOP" button on the receiver for 5 seconds. The indicator light flashes quickly 3 times.
2. Press the "DOWN + STOP" button on the receiver for 5 seconds. The setting is transferred.

Note: For dot moving, press UP/DOWN button less than 1.5 seconds. For continuous moving, press UP/DOWN button more than 1.5 seconds.

4. Delete single code

The single channel memory on the transmitter will be deleted after this operation.

1. Press the "STOP" button on the receiver for 5 seconds. The indicator light flashes quickly 3 times.
2. Press the "DOWN" button on the transmitter within 10 seconds. The code is deleted.

5. Delete all codes

All memories on the receiver will be deleted after this operation.

1. Press the "DOWN + STOP" button on the receiver for 5 seconds. The indicator light flashes quickly 3 times.
2. Press the "DOWN + STOP" button on the receiver for 5 seconds. All codes are deleted.

VI. Trouble and shootings

Document version: 4.0114.0089(V1.2)

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning statement:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.