External Factor Checklist Overview

This document provides a checklist for common external factors that may affect bidet functionality, along with detailed instructions for troubleshooting, cleaning, removal, and installation.

1. Resetting the Bidet

Follow these steps to reset the bidet:

1. Unplug the unit.
2. Fully open the water shutoff valve.
3. Plug the unit back in.
4. Press the nozzle cleaning button to check if the nozzle extends, then press it again to ensure it retracts.
5. Place your hand on the seat sensor (shown in the photo) and press the posterior or feminine button on the remote to see if the unit is functional.

Description of the image on page 1: A top-down view of a bidet toilet seat. A hand is shown touching the seat sensor area, with dashed red squares highlighting the sensor location and the general area where the hand is placed.

2. Cleaning the Main Strainer Filter

Detailed instructions for cleaning the main strainer filter are provided in Section 2.

3. Removing the Water Pressure Regulator

Detailed instructions for removing the water pressure regulator are provided in Section 3-1.

1. Power Reset, Open Water Valve, and Remote Setting

This section details the process of resetting power, opening the water valve, and adjusting remote settings.

1. Unplug the power cord.

   Description of image 1 on page 2: A power cord being unplugged from a wall socket.

2. Turn the water valve fully open in the direction of the arrow.

   Description of image 2 on page 2: A water shutoff valve being turned fully open, indicated by an arrow.

3. Plug the power cord back in.

   Description of image 3 on page 2: A power cord being plugged into a wall socket.

4. Check the water pressure setting on the remote and set it to level 5.

   Operate the product to confirm water pressure.

   Description of image 4 on page 2: A close-up of a bidet remote control. The left panel shows various buttons and indicators. The right panel shows the "Pressure" setting with several illuminated LED lights, indicating a higher pressure level. An arrow points from the left panel to the right, suggesting a transition or adjustment.

2. Cleaning the Main Strainer

Follow these steps to clean the main strainer filter.

1. Turn the water valve fully closed in the direction of the arrow.

   Description of image 1 on page 3: A water shutoff valve being turned fully closed, indicated by an arrow.

2. Use a tool to turn and remove the marked part of the strainer.

   Description of image 2 on page 3: A tool being used to unscrew and remove a part of the bidet's water inlet connection, specifically the strainer housing.

3. Check the filter for any debris.

   Description of image 3 on page 3: A close-up of a mesh filter, with dashed red lines highlighting areas where debris might be found.

4. Rinse the removed mesh under running water.

   Description of image 4 on page 3: The removed mesh filter being rinsed under running water in a sink.

5. Reattach the strainer by turning it in the direction of the arrow using a tool.

   Description of image 5 on page 3: The strainer being reattached to the water inlet connection using a tool, with a curved arrow indicating the direction of tightening.

6. Turn the water valve fully open in the direction of the arrow.

   Description of image 6 on page 3: The water shutoff valve being turned fully open, indicated by an arrow.

3-1. Removing the Bidet & Water Pressure Regulator

This section provides instructions for removing the bidet unit and its water pressure regulator.

1. Unplug the power cord.

   Description of image 1 on page 4: A power cord being unplugged from a wall socket.

2. Turn the water valve to the closed position.

   Description of image 2 on page 4: A water shutoff valve being turned to the closed position, indicated by an arrow.

3. Press the manual flushing button on the side to release pressure.

   Description of image 3 on page 4: A button on the side of the bidet unit being pressed. Dashed red squares highlight the button.

4. Pull the lever plate forward and lift to remove the bidet.

   Description of image 4 on page 4: A lever plate at the rear of the bidet being pulled forward, with arrows indicating the motion. The bidet unit is shown being lifted.

5. Disconnect the water supply hose.

   Description of image 5 on page 4: A hand disconnecting a flexible water supply hose from the bidet unit.

6. Use a tool to hold the groove of the water pressure regulator.

   Description of image 6 on page 4: A tool being used to grip and turn a grooved part of the water pressure regulator. A warning symbol (triangle with exclamation mark) is visible, along with text "HAND TIGHT ONLY NO Teflon Tape".

7. Pull out the water pressure regulator to remove it.

   Description of image 7 on page 4: The water pressure regulator being pulled out from its housing.

3-2. Installing the Bidet

This section provides instructions for installing the bidet unit.

1. Connect the water supply hose.

   Description of image 1 on page 5: A hand connecting a flexible water supply hose to the bidet unit. Dashed red circles highlight the connection point.

2. Align the unit with the base and catch plate, then secure it.

   Description of image 2 on page 5: The bidet unit being aligned with its base and catch plate on the toilet.

3. Turn the water valve open in the direction of the arrow.

   Description of image 3 on page 5: A water shutoff valve being turned fully open, indicated by an arrow.

4. Plug in the power cord.

   Description of image 4 on page 5: A power cord being plugged into a wall socket.