MOZA SR-P Racing Pedals

Introduction

This document serves as the user manual for the MOZA SR-P Racing Pedals, designed to provide superior control with its load cell technology. It covers installation, adjustment, packing details, and warranty information.

01 Pedal Installation

Follow these steps to install your SR-P Racing Pedals:

1. Place the pedals on the footrest. Use a 2.5mm hexagon wrench to fix the M4*10 screws to the footrest. It is recommended that all 4 screws of each pedal are tightened to ensure stability.
2. Connect the wires to the corresponding ports. The connecting wire of the clutch angle sensor needs to pass through the middle of the brake base; otherwise, it may press on the wire harness after installing the pedal. Use the wire under the pedal base to clamp the wire harness and prevent it from being worn or tangled during intense driving.

3. Once the wires are connected and the USB cable is plugged into the computer, you will see the status of the SR-P pedal in the MOZA Pit House software. If the status remains gray or does not respond, unplug the USB port from the PC, turn off the MOZA Pit House, reconnect the USB port, and then turn on the MOZA Pit House. For bases with a pedal interface, connection can also be made through a dual RJ45 data cable.
4. You can check the working status of the pedal, reset the pedal starting point, ending point, and pedal travel within the MOZA Pit House software.

02 How to Adjust the Pedal Spacing

Adjust the spacing between the pedals and the base holes by moving them left and right. Select the appropriate screw hole and then tighten the screw. The accelerator, brake, and clutch pedals are adjusted in the same way.

03 Instructions for Adjusting the Pedal Board Height

To adjust the height of the pedal board, use a 2.5mm hexagon wrench to turn the screws on the board surface counterclockwise. Use a 7mm open-end wrench to remove the nuts on the back and the screws on the board. Move the board up or down to adjust the height according to your needs, then fasten the nuts and screws to the board surface. The accelerator, brake, and clutch pedals are adjusted in the same manner.

04 Packing Details

The package includes:

• 1 x SR-P pedal
• 1 x Tool kit:
  • M4*10 socket head countersunk head screws (x12)
  • M8*12 hexagon socket head screws (x3)
  • M6*20 socket head cap screws (x2)
  • 2.5mm hexagon wrench (x1)
  • 7mm open end wrench (x1)
  • 5mm hexagon wrench (x1)
• 1 x Type A to Type B USB cable
• 1 x RJ45 data cable

Note: Connect the pedal to either the base or the PC, but do not connect it to both at the same time.

Warranty Information

Warranty Period: The base, pedals, and display screen are covered by a 12-month warranty from the date of purchase. The device casing, manual, cables, screws, wrenches, and packaging are not included in the one-year free warranty service; paid services are available.

Conditions for Voiding Free Warranty:

• Exceeding the warranty period.
• Lack of warranty certificate and valid invoice, unless proof of purchase within the warranty period is provided.
• The model number on the warranty certificate does not match the product or has been altered.
• Damage caused by unauthorized repair personnel.
• Damage due to force majeure (acts of God).
• Damage caused by failure to use, maintain, or service the product according to the user manual.

Warranty duration may vary by product part, and due to differences in national laws and regulations. For warranty periods in specific countries and regions, please consult the MOZA official website or contact your authorized MOZA dealer at the time of purchase.

Manufacturer and Representative Information

Manufacturer: Shenzhen Gudsen Technology Co., Ltd

Address: Room 1903-1904, Building 3, Nanshan ZhiyuanChongwen Park, No. 3370 Liuxian Avenue, Nanshan District, Shenzhen China

Web: www.mozaracing.com

E-mail: info@mozaracing.com

Made in China

EU Representative: Gudsen Technology EU GmbH

Address: Birkenstrasse 23, 40233 Düsseldorf

Contact: JUNWEN DING

Email: support@gudsen.com

UK Representative: Gudsen Technology UK Limited

Address: Tc-Abo, Luminous House, 300 South Row Milton Keynes, MK9 2FR, United Kingdom

Contact: JUNWEN DING

Email: support@gudsen.com