ASSMANN Electronic GmbH | Lüdenscheid, Germany
User Manual for DIGITUS models including: 4K HDMI Extender Set over IP, 4K HDMI Extender Set over CAT
File Info : application/pdf, 8 Pages, 862.76KB
DocumentDocument4K HDMI Extender Set over IP/CAT User Manual DS-55124 · DS-55125 (RX unit) Rev. 2 Important Safety notice Please read below safety instructions carefully before installation and operation: 1. Please pay attention to all the warnings and hints on this device 2. Do not expose this unit to rain, moisture and liquid 3. Do not put any stuff into the device 4. Do not repair or open this device without professional people's guidance 5. Shut off power and make sure environment is safe before installation Do not plug-in/out the network cables and IR cables when it is in using to avoid cables damage 6. Please note that our extender supports 5V power supply also, but the 5-Volt power port is alternative. Please do not connect PoE power supply and 5V power supply at the same time, choose each one would work Introduction HDMI over IP extender, takes the advantages of the latest transmission technology, extends your HDMI video/audio with the resolution of 4Kx2K 30Hz up to 120m (394 feet) via single network cable. Supports IR signal transmission, to control media playback of the signal source device at the display location. Supports PoE. Package Contents HDMI EXTENDER sender TX x1pcs HDMI EXTENDER receiver RX x1pcs User Manual x1pcs IR OUT IR blaster extension cable*1pcs IR IN IR receiver extension cable*1pcs Installation Requirements 1. HDMI source device (computer graphics card, DVD, PS3, HD monitoring equipment etc.). 2. HDMI display device like SDTV, HDTV, and projector with HDMI port. 3. Network cables: CAT 5/5e/6 network cables 4. Transmission length: CAT5 80m/CAT5E 100m/CAT6 120m 5. PoE powered device: Support and compliant with IEEE802.3af international standard switcher and other PoE power supply devices. The maximal wattage of the transmitter or receiver is 10w only. Panel Description 1. HDMI EXTENDER TX (Sender) Reset HDMI signal input IR signal output to connect with blaster extension cable Power Light Power input (DC5V) Data transmission light Network link light HDbitT signal output (PoE Input) 2. HDMI EXTENDER RX (Receiver) Reset HDMI signal output IR signal input to connect with IR receiver extension cable Power Light Power input (DC5V) Data transmission light Network link light HDbitT signal input (PoE Input) Installation Procedures 1. Connections 1.1. Point to Point connection: Up to 120 meters transmission distance over single CAT6 (High quality cable can reach 150 meters) HDMI EXTENDER TX (Sender) DVD HDMI IN HDMI EXTENDER RX (Receiver) HDMI OUT PoE Switch CAT5/5E/6 Cable TV 1.2. Router Connection: By using network router/repeater, realize unlimited extension. DVD HDMI IN CAT5/5E/6 Cable HDMI EXTENDER TX (Sender) PoE Switch PoE Switch*N HDMI OUT TV HDMI EXTENDER RX (Receiver) 1.3. One-to-many Connection: By using network router/switch, one sender to several receivers, realize extender & splitter function. DVD HDMI IN CAT5/5E/6 Cable HDMI EXTENDER TX (Sender) CAT5/5E/6 PoE Switch Cable HDMI OUT HDMI EXTENDER TV RX (Receiver) HDMI OUT HDMI EXTENDER TV RX (Receiver) HDMI OUT HDMI EXTENDER TV RX (Receiver) Specification Product type 4Kx2K HDMI over IP CAT5/5e/6 Extender with PoE feature Up to 120m, support one to many, 4K@30Hz Max transmission rate 10.2Gbps Color Depth 8bit 480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz, Supported video resolution 720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz, 4K×2K@24/25/30Hz Supported audio formats LPCM HDMI connector Type A, Female, 19-pin RJ45 Connector RJ45 Latency <220ms Input and Output TMDS signal 0.7~1.2Vp-p (TMDS) Input and Output DDC signal 5Vp-p (TTL) PoE input Support IEEE802.3af (Input power 10W) Voltage Adapter Power consumption DC5V/2A (Power adapter not included) TX<6W, RX<5W ESD protection 1a (contact discharge) level 3 1b (air-gap discharge) level 3 International Standard: IEC61000-4-2 Operating temperature (0°C ~ 60°C) 32°F ~ 140°F Storage temperature (-10°C ~ 70°C) -14°F ~ 94°F Relative humidity 0 ~ 90% RH (Non-condensing) Dimension 119(L) x 94(W) x 23.8(H) mm Material Metal housing Weight TX: 275g, RX: 275g Color black FAQ Q: TV display "Waiting for connection" on the right corner? A: Please check if the power supply of TX (Sender) and switcher (if used) is connected, and make sure connecting cable is firmly. Q: TV display "Please check the TX input signal"? A: Please check if there is a HDMI signal input of TX Try to connect the signal source directly to display device to see if there is signal output from source device or change the signal source, HDMI wire and try again Q: When playing 4Kx2K source, screen is back without any content? A: Make sure both TV and HDMI cable support HDMI1.4. Q: Display not fluent, not stable? A: Please check the cable length between the TX to switch, the switch to the RX and the connection between each level is within the required range. Click the "Reset" button on the TX/RX front panel, reset and reconnect. Disclaimer The product name and brand name may be registered trademark of related manufacturers.TM and ® may be omitted on the user manual. The pictures on the user manual are just for reference, and there may be some slight difference with the real products. We reserve the rights to make changes without further notice to a product or system described herein to improve reliability, function or design. This is a Class A product. In home environment, this product may cause radio interference. In this case, the user may be required to take appropriate measures. Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address. www.assmann.com Assmann Electronic GmbH Auf dem Schüffel 3 58513 Lüdenscheid Germany