Altronix Home
Installation Guide for Altronix models including: NetWaySP1BTWP Series, NetWaySP1BTWP, 802.3bt Media Converter Injectors, NetWaySP1BTWP 802.3bt Media Converter Injectors, Media Converter Injectors, Converter, Converter Injectors, Injectors
2021-07-17 — Overview: Altronix NetWaySP1BT Series 802.3bt media converter/injectors provide a single 802.3bt (4PPoE) port up to 90W.
Altronix NETWAYSP1BTWPX | Single 1G Fiber Optic SFP, Hardene
File Info : application/pdf, 12 Pages, 1.26MB
DocumentDocumentFiber Solution NetWaySP1BTWP Series 802.3bt Media Converter/Injectors with Integral Power Models Include: NetWaySP1BTWP - 802.3bt Media Converter/Injector with Integral Power. - NEMA4/4X rated outdoor enclosure. NetWaySP1BTWPX - 802.3bt Media Converter/Injector with Integral Power. - NEMA4/4X rated outdoor enclosure. - Accommodates up to four (4) 12VDC/4AH batteries. Installation Guide DOC#: NetWaySP1BTPWP Rev. 032620 More than just power.TM Installing Company: _______________ Service Rep. Name: __________________________________ Address: _____________________________________________ Phone #: __________________ Table of Contents: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Recommended Altronix SFP Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Installation Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 4 Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 4 Input/Data Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 4 NetWaySP1BTWP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 5 NetWaySP1BTWPX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 6 Typical Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 7 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 7 Wall Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 8 Mechanical Drawing and Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 9-10 - 2 - NetWaySP1BT Powered Series Installation Guide Overview: Altronix NetWaySP1BT Series 802.3bt media converter/injectors provide a single 802.3bt (4PPoE) port up to 90W and accommodate Fiber (1000Base-X/SX/LX) or structured cable to transmit data. Units can be deployed with structured cable, conventional single/multimode fiber or composite cable (fiber + copper combined). Cameras/edge devices may be located up to 100m from the unit. Features: Agency Listings: LED Indicators (Refer to Fig. 4, Pg. 4): · CE European Conformity. · Yellow and Green LEDs (RJ45 jacks): Input: · 115VAC, 60Hz, 2.5A or 230VAC, 50/60Hz, 1.3A. Fiber Port: · One (1) 1Gb SFP port. *See below for recommended SFP modules. PoE Port: · Single port rated up to 90W max. · IEEE 802.3af, 802.3at and 802.3bt compliant. Data Port: · Connectivity: RJ45, auto-crossover. · Wire type: 4-pair CAT5e and higher. · Speed: 10/100/1000 Mbps. · Distance: up to 100m. Battery Backup: · Built-in charger for sealed lead acid or gel type batteries. · Automatic switch over to stand-by battery when AC fails. Yellow (left) LED: 10/100 Mbps. Green (right) LED: 1000 Mbps. · Green PoE LEDs: Indicate PoE present. · Green SFP (Fiber) LED: Indicates SFP connection. Mechanical: NetWaySP1BTWP: · NEMA4/4X, IP66 Rated enclosure for outdoor use. · Dimensions (H x W x D approx.): 13.31" x 11.31" x 5.59" (338.1mm x 287.3mm x 142mm). NetWaySP1BTWPX: · NEMA4/4X, IP66 Rated enclosure for outdoor use. · Accommodates four (4) 12VDC/4AH batteries (48V of backup). · Dimensions (H x W x D approx.): 17.53" x 15.3" x 6.67" (445.3mm x 388.6mm x 169.4mm). Environmental: · Refer to Environmental Conditions on page 5. Recommended Altronix SFP Modules: Altronix P1MM, P1SM10, P1AB2K and P1GCE are hot-pluggable SFP fiber transceiver modules and are readily usable with all Altronix Spectrum fiber optic equipment for 1Gb transmission rates. P1MM For use with Multi-Mode Fiber for distances up to 550m. P1SM10 For use with Single-Mode Fiber for distances up to 10km. P1AB2K For use with Single Strand Single-Mode Fiber for distances up to 2km. P1GCE For use with CAT5e or better for distances up to 100m. NetWaySP1BT Powered Series Installation Guide - 3 - Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. All units should be installed by a trained service personnel. Installation: 1. Remove backplane from enclosure prior to drilling. Do not discard hardware. Note: Make sure that hardware will not interfere with components of the circuit board. 2. Mark and drill desired inlets on the enclosure to facilitate wiring. Maximum NEMA type 4X rated fittings to be used are 0.5". Follow manufacturer's specifications for the appropriate size opening. Note: Inlets for conduit fittings should only be made on the bottom of the enclosure. To facilitate wire entry utilize weather-tight NEMA rated connectors (supplied), bushings, and cable. 3. Clean out the inside of enclosure before remounting circuit boards/backplane. 4. Mounting NEMA4/4X rated enclosure (Enclosure Dimensions, pg. 9, 10): Wall mount: Mount unit in desired location. Mark and drill holes to line up with the top and bottom hole of the enclosure flange. Secure enclosure with appropriate fasteners (e. g. screws and anchors; bolts and locking nuts, etc.) that are compatible with mounting surface and are of sufficient length/construction to ensure a secure mount (Fig. 5, pg. 8). Pole Mount: Refer to Fig. 6 - 10, pg. 8. 5. Mount backplane in enclosure with hardware. Power Connection: Before powering unit, set input voltage selection switch to proper Input Voltage position (Fig. 2a, pg. 5, Fig. 3a, pg. 6). Units are factory set for 115VAC. 1. Connect AC power from overcurrent protective device circuit breaker (20A @ 115VAC, 60Hz or 16A @ 230VAC, 50/60Hz) to the terminals marked [L, N] on power supply board (Fig. 2, 3, pg. 5, 6). Connect ground lug to earth or green branch wire on backplane (12AWG min.). Use 14AWG or larger for all power connections (Battery, DC output, AC input). Keep power-limited wiring separate from non power-limited wiring by utilizing separate knockouts/ inlets. Minimum 0.25" spacing must be provided. CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing equipment. There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel. 3. Battery Backup (if desired): Connect four (4) 12VDC batteries wired in series to terminals marked [ BAT +] (Fig. 3, pg. 5), carefully observing polarity. When use of stand-by batteries is desired, they must be lead acid or gel type. Note: When batteries are not used, a loss of AC will result in the loss of output voltage. Input/Data Connections: 1. Connect structured cable from port marked [Data Port] on NetWaySP1BT to a PoE midspan/endspan (Fig. 1, pg. 4). 2. Connect fiber optic cable to a fiber SFP module. Connect the module to the port marked [SFP] on the NetWaySP1BT. Connect the other end of fiber cable to an SFP module of a remote device. SFP LED will illuminate indicating data connection (Fig. 1, pg. 4). 3. Using 4-pair CAT5e or higher cable connect PoE load device to be powered to the port marked [802.3bt Output] on NetWaySP1BT. After authentication and classification have been established, [PoE Signal] LED will illuminate indicating PoE presence. IEEE 802.3af, 802.3at and 802.3bt compliant port rated up to 90W max Fig. 1 Yellow LED 10/100 Mbps 48-56VDC Input + -- + 48VDC to 56VDC Input 802.3bt PoE Data Output Signal Port Green LED 1000 Mbps Ethernet Data Port Fiber SFP Signal One (1) Gb SFP port for Fiber SFP LED Indicates data connection PoE LED indicates PoE present - 4 - NetWaySP1BT Powered Series Installation Guide NetWaySP1BTWP Fig. 2 115VAC 230VAC Fig. 2a BAT + DC + Brooklyn, NY U.S.A. www.altronix.com NetWaySP1BT 802.3bt Converter/Injector Input: 4856VDC Output: IEEE 802.3bt (90W) 48-56VDC -- Input + 802.3bt Output PoE Signal Data Port Fiber SFP Signal Ground 115VAC 230VAC 115/230VAC Input Ground Lug LG N To stand-by batteries NetWaySP1BT Powered Series Installation Guide - 5 - NetWaySP1BTWPX Fig. 3 Optional rechargeable 12VDC/4AH battery Optional rechargeable 12VDC/4AH battery Optional rechargeable 12VDC/4AH battery Optional rechargeable 12VDC/4AH battery Fig. 3a 115VAC 230VAC BAT + DC + Brooklyn, NY U.S.A. www.altronix.com NetWaySP1BT 802.3bt Converter/Injector Input: 4856VDC Output: IEEE 802.3bt (90W) 48-56VDC -- Input + 802.3bt Output PoE Signal Data Port Fiber SFP Signal Ground 115VAC 230VAC To stand-by batteries 115/230VAC Input Ground Lug LG N - 6 - NetWaySP1BT Powered Series Installation Guide Fig. 4 Typical Application: Brooklyn, NY U.S.A. www.altronix.com NetWaySP1BT 802.3bt Converter/Injector Input: 4856VDC Output: IEEE 802.3bt (90W) NetWaySP1BT Converts Ethernet or Fiber to 802.3bt PoE port From power supply 48-56VDC 802.3bt PoE Data -- Input + Output Signal Port Fiber SFP Signal Fiber PoE+ (90W) PTZ CAT5e/6 OR Data from Midspan/Endspan CAT5e/6 Parameter Ports Input Power Requirements Indicators Evironmental Conditions Regulatory Compliance Weights (approx.) Technical Specifications: Description One (1) 1Gb SFP port, one (1) Data port. One (1) IEEE 802.3af, 802.3at and 802.3bt compliant output port rated up to 90W max. 115VAC, 60Hz, 2.5A or 230VAC, 50/60Hz, 1.3A. Yellow and Green LEDs (RJ45 jacks): IP Link status, 10/100/1000 Base-T/active. PoE Green LED: Indicates PoE present. Fiber Signal Green LED: Indicates SFP connection. Temperature: Operating: 60W: 80W: 90W: Storage: Relative Humidity: Operating Altitude: 40ºC to 75ºC ( 40ºF to 167ºF). 40ºC to 70ºC ( 40ºF to 158ºF). 40ºC to 60ºC ( 40ºF to 140ºF). 40ºC to 85ºC ( 40ºF to 185ºF). 85% +/5%. 304.8 to 2,000m. CE European Conformity. NetWaySP1BTWP: Product: 10.5 lb. (4.76 kg) | Shipping: 11.9 lb. (5.4 kg). NetWaySP1BTWPX: Product: 15 lb. (6.8 kg) | Shipping: 17.5 lb. (7.9kg). NetWaySP1BT Powered Series Installation Guide - 7 - Wall Mount Installation: 1- Place unit at desired location and secure with mounting screws (not included) (Fig. 5, pg. 8). Fig. 5 Pole Mounting Using Optional Pole Mount Kit PMK1 (NetWaySP1BTWP) or PMK2 (NetWaySP1BTWPX): This installation should be made by qualified service personnel. This product contains no serviceable parts. PMK1 and PMK2 outdoor pole mount kits are designed to simplify the installation of Altronix outdoor rated power supplies and accessories housed in models WP1, WP2, WP3 and WP4 NEMA rated enclosures. PMK1 and PMK2 can be mounted on 2" to 8" (50.8mm to 203.2mm) diameter round or 5" (127mm) square poles. Brackets are designed for use with the Wormgear Quick Release Straps (two included). 1. Thread one (1) wormgear quick release strap through the slots on the back of a mounting bracket (Fig. 6, pg. 8). 2. Once the desired height of the top Pole Mount bracket is achieved, tighten the straps down by sliding open end of the strap through the locking mechanism on the strap, then tighten the screw with flat head screwdriver or 5/16" hex socket driver (Fig. 7, pg. 8 and Fig. 9, pg. 8). Fig. 6 Fig. 7 Fig. 8 3. Attach the bottom bracket to the enclosure by inserting bolts through the flange of the enclosure and into the bracket, tightening bolts with a 7/16" hex socket (Fig. 8, pg. 8). 4. Thread the second wormgear quick release strap through the slots on the back of the bottom mounting bracket (Fig. 9, pg. 8). 5. Mount enclosure onto the top bracket by inserting bolts through flange of the enclosure and into the bracket, tightening bolts with a 7/16" hex socket (Fig. 7, pg. 8). 6. Tighten the straps of the bottom bracket down by sliding the open end of the strap through the locking mechanism on the strap, then tighten screw with flat head screwdriver or 5/16" hex socket driver (Fig. 7, pg. 8). 7. Clip excess straps. Fig. 10 Fig. 10a 2" to 8"(50.8mm to 203.2mm) 5" (127mm) square pole Fig. 9 diameter round pole - 8 - NetWaySP1BT Powered Series Installation Guide NetWaySP1BTWP Enclosure Drawing and Dimensions (H x W x D approx.): 13.31" x 11.31" x 5.59" (338.1mm x 287.3mm x 142mm) FRONT VIEW RIGHT SIDE VIEW 11.31" (287.3mm) 3.96" (100.6mm) 1.61" (40.9mm) 12.75" (323.9mm) 13.31" (338.1mm) 13.50" (342.9mm) 12.00" (304.8mm) 10.25" (260.4mm) 5.59" (142mm) FRONT VIEW COVER REMOVED 10.75" (273.1mm) 10.00" (254mm) 8.25" (209.6mm) END VIEW STAINLESS STEEL PIANO HINGE 10-32 X 0.375" (9.5mm) BRASS INSERT (X4) PADLOCK LATCH ATTACHED WITH RIVETS (Ø 0.375" (9.5mm) PADLOCK EYE) 8.00" (203.2mm) Ø 0.32 (8.1mm) MOUNTING HOLE TYP. 4 PLACES 10-32 X 0.25" (6.4mm) BRASS INSERT (X2) NetWaySP1BT Powered Series Installation Guide - 9 - NetWaySP1BTWPX Mechanical Drawing and Dimensions (H x W x D approx.): 17.53" x 15.3" x 6.67" (445.3mm x 388.6mm x 169.4mm) FRONT VIEW 15.3" (388.6mm) RIGHT SIDE VIEW 1.67" (42.4mm) 5.00" (127mm) 17.36" (441 mm) 16.73" (425mm) A A FRONT VIEW COVER REMOVED 14.54" (369.3mm) 14.00" (355.6mm) 12.23" (310.6mm) 316 STAINLESS STEEL PADLOCK LATCH ATTACHED WITH RIVETS. Ø 0.375 PADLOCK EYE SECTION A-A 0.125" (3.2mm) 14.25" (362mm) 16.74" (425.2mm) 6.67" (169.4mm) 4.94" (125.5mm) 5.77" (146.6mm) 6.41" (162.8mm) 0.75" (19.1mm) 17.53" (445.3mm) 16.00" (406.4mm) 10-32 X 0.250 BRASS INSERT 4 PLCS. - 10 - MOUNTING PLATE END VIEW Ø 0.32" (8.1mm) WALL MOUNTING HOLE X 4 12.00" (304.8mm) NetWaySP1BT Powered Series Installation Guide Notes: NetWaySP1BT Powered Series Installation Guide - 11 - Notes: Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty IINetWaySP1BT Series Powered G08U MEMBER - 12 - NetWaySP1BT Powered Series Installation Guide