Schaub Lorenz SLW SW7440 S Washing Machine User Manual

Safety Instructions

General Safety

For your safety, it is necessary to follow the information provided in this manual to minimize the risk of fire or explosion, electric shock, or to prevent damage to property, injury, or death.

!Warning! Electric Shock Hazard!

• If the cord is damaged, it must be replaced by the manufacturer, a service agent, or a similarly qualified person to avoid hazards.
• In case of damage to the washing machine, do not use it until it has been repaired by the manufacturer, its service agent, or other qualified specialists. Electric shock hazard!
• Children aged 8 and above, as well as persons with reduced physical, sensory, or mental capabilities, or with lack of experience and knowledge, should only use the appliance if they are supervised or have been instructed on the safe use of the appliance and understand the associated hazards. Children must not play with the appliance.
• Cleaning and maintenance of the appliance must not be carried out by children without supervision.
• Children must be supervised to ensure they do not play with the appliance.
• Children under 3 years of age should be kept under constant supervision or away from the appliance.
• Animals and children may climb into the washing machine drum. Check the drum before each wash.
• Do not climb or sit on the appliance.

Appliance Installation Location

• All detergents and additives should be stored in a safe place inaccessible to children.
• Do not install the machine on a carpet. Blocking the carpet openings may damage the machine.
• Keep the appliance away from heat sources and direct sunlight to avoid corrosion of plastic and rubber parts.
• Do not use the appliance in a humid environment or in rooms containing explosive or corrosive gases. In case of water leakage or splashing, let the appliance dry in the open air.
• The appliance must not be installed behind a locking door, a sliding door, or a door with a hinge on the opposite side of the washing machine.
• Do not use the machine in rooms with temperatures below 5°C. This may damage its parts. If unavoidable, completely drain the water from the appliance after each use (see "Maintenance - Cleaning the drain pump filter") to prevent damage caused by freezing. Never use flammable aerosols or substances in the immediate vicinity of the appliance.

Installation

• Before using the appliance, remove all packaging material and transport bolts. Otherwise, serious damage may occur.
• This appliance is equipped with one inlet valve and can only be connected to the cold water supply system.
• After installation, the power plug must remain accessible.
• Before first use, the appliance should be run once without any clothes inside.

Electrical Connection

• Connect the device to an earthed socket protected by a fuse, corresponding to the values in the "Technical Specifications" table. Earthing installation must be carried out by a qualified electrician. Ensure the machine is installed in accordance with local regulations.
• Water and electricity connection must be carried out by a qualified specialist in accordance with the manufacturer's instructions and local safety regulations.

!Warning!

• Do not use multiple plugs or extension cords.
• The appliance must not be switched on via an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off.
• Do not unplug the appliance if there is flammable gas around.
• Never unplug the appliance with wet hands.
• Always pull the plug, not the cable.
• Always disconnect the appliance from the mains when not in use.

Water Connection

• Check the connections of the inlet pipes for water, the water tap, and the outlet hose for possible problems related to changes in water pressure. If the connections are loose or leaking, turn off the water tap and repair it. Do not use the appliance until qualified specialists have properly installed the pipes and hoses.
• The glass door can get very hot during operation. Keep children and pets away from the machine while it is running.
• The water inlet and outlet hoses must be securely installed and remain undamaged. Otherwise, water leakage may occur.
• Do not remove the drain pump filter while there is still water in the appliance. A large amount of water may leak out, and there is a risk of scalding from hot water.

Operation and Technical Maintenance

• Never use flammable, explosive, or toxic solvents. Do not use gasoline, alcohol, etc., as detergents. Use only detergents suitable for machine washing.
• Check pockets to ensure they are empty. Sharp and hard objects such as coins, brooches, nails, screws, stones, etc., can cause serious damage to the washing machine.
• Remove items like lighters and matches from pockets.
• Rinse items washed by hand thoroughly.
• Items contaminated with substances such as vegetable oil, acetone, alcohol, gasoline, kerosene, stain removers, turpentine, wax, and wax removers should be washed in hot water with extra detergent before drying in the appliance.
• Items containing foam (latex foam), shower caps, waterproof textiles, rubber-backed items, or pillows with foam padding should not be tumble dried.
• Fabric softeners or similar products should be used in accordance with the recommendations in their instructions.
• Never try to force the door open. The door will open shortly after the cycle ends.
• Please do not close the door with excessive force. If you find it difficult to close the door, please check if the clothes are inserted and distributed correctly.
• Always disconnect the appliance from the mains and close the water tap before cleaning and maintenance, and after each use. Never pour water on the appliance for cleaning. Risk of electric shock!
• Repairs must only be carried out by the manufacturer, a service agent, or qualified specialists to avoid hazards. The manufacturer is not liable for damage caused by intervention by unauthorized persons.

Moving

• Before transport:
• Transport bolts must be reinstalled on the machine by a specialized technician.
• Any accumulated water must be drained from the machine.
• The appliance is heavy. Transport with care. Never hold any protruding part of the machine when lifting. The machine door must not be used as a handle.

Intended Use

The product is intended for domestic use only with household quantities and for laundry suitable for machine washing and drying. This appliance is intended for indoor use only and is not designed for built-in use. Use only in accordance with this instruction. The appliance is not intended for commercial use.

Any other use is considered improper. The manufacturer is not liable for any damage or injury that may result from this.

This appliance is intended for use in domestic and similar applications, such as:

• Staff kitchens in shops, offices, and other workplaces;
• Farmhouses;
• Guest use in hotels, motels, and other residential premises;
• Bed and breakfast type establishments;
• Communal areas in apartment blocks or laundries.

Disposal

This symbol on the product or its packaging indicates that this product should not be treated as household waste. Instead, it should be taken to the appropriate collection point for electrical and electronic equipment recycling. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could be caused by inappropriate waste handling of this product.

Installation

Appliance Description

The image above is for reference only. The actual configuration will depend on the physical product.

Contents:

• 4 x Plugs
• Inlet hose for cold water
• User Manual

Installation

Installation Area

!Warning! A stable position is important to prevent unintentional movement of the product! Ensure the machine is level and stable.

• Ensure the device is not standing on the power cord.
• Ensure that the minimum clearances from the walls are observed, as shown in the figure.

Before installing the machine, choose a location that meets the following parameters:

1. A rigid, dry, and level surface
2. Absence of direct sunlight
3. Sufficient ventilation
4. Room temperature above 0°C
5. Away from heat sources, such as appliances running on coal or gas.

Unpacking

!Warning! Packaging material (e.g., film, polystyrene) can be dangerous for children. Suffocation hazard! Keep all packaging out of reach of children.

1. Remove the cardboard box and polystyrene packaging.
2. Lift the washing machine and remove the base packaging. Ensure the small triangular foam (a) is removed with the bottom packaging. If not, place the device on its side and remove it manually.
3. Remove the tape securing the power cord and drain hose.
4. Remove the inlet hose from the drum.

Removing Transport Bolts

!Warning! Before use, it is necessary to remove the transport bolts from the back.

• Loosen the 4 transport bolts using a wrench.
• Remove the bolts, including the rubber parts, and save them for future use.
• Close the openings with the covers.

Leveling the Appliance

!Warning! The lock nuts on all four feet must be tightly screwed to the housing.

1. Loosen the nut.
2. Unscrew the feet until they are in firm contact with the floor.
3. Adjust the feet and secure them with a wrench. Ensure the appliance is stable on the floor.

Connecting the Water Inlet Hose

!Warning! To prevent water leakage and other damage, follow the instructions in this chapter! Do not kink, crush, or modify the water inlet hose.

• Connect the water inlet hose to the inlet valve and the cold water tap as shown.

Attention! Connect manually, do not use tools. Check if the connections are watertight.

Drain Hose

!Warning! Do not kink or stretch the drain hose. Position the drain hose correctly, otherwise, leaks may occur.

There are two ways to position the end of the drain hose:

1. Connect the hose to the drain trough.
2. Connect the hose to the drain standpipe.

Operation

Quick Start

Caution! Before washing, please ensure the washing machine is installed correctly. Your appliance has been thoroughly checked before leaving the factory. To remove residual water and neutralize possible odors, it is recommended to clean the appliance before first use. For this reason, run the cotton program at 90°C without clothes and detergent.

1. Before Washing

• Connect
• Open water tap
• Load
• Close
• Add detergent

Attention! Detergent should be added to compartment I if the pre-wash function is selected.

2. Washing

1. Select program
2. Select function or leave default settings
3. Press Start/Pause to start the program

3. After Washing

The door lock and indicators [Start / Pause] flash with a buzzer sound, or two small dots flash on the digital screen.

Before Each Wash

• The ambient temperature of the washing machine should be 5-40°C. If used at temperatures below 0°C, the inlet valve and drainage system may be damaged. If the machine is installed in freezing conditions, it should be moved to a place with normal ambient temperature. Before use, ensure that the water inlet hose and drain hose are not frozen.
• Before washing, check the care labels on the clothes and the instructions for using the detergent. Use a low-foaming or non-foaming detergent suitable for machine washing.

• Check the care label for the garment.
• Sort laundry by color and fabric type.
• Fasten all zippers.
• Empty pockets of items.
• Place small items in a laundry bag.
• Turn clothes inside out.

!Warning! Do not wash or dry items that have been cleaned, washed, impregnated, or soaked with flammable or explosive substances such as wax, oil, paint, gasoline, alcohol, kerosene, and other flammable materials.

Washing individual items of clothing can easily create a large imbalance and cause concern due to imbalance. Therefore, it is recommended to add one or two more items of laundry to ensure a smooth spin.

Detergent Compartment

• Compartment for pre-wash
• Compartment for main wash
• Compartment for softeners, rinse aids

Press the button to pull out the detergent compartment.

Attention! Detergent should only be added to compartment "I" after selecting the pre-wash function.

Detergent Recommendations

Attention!

• Agglomerating or viscous detergent or additive can be diluted with a small amount of water before pouring into the detergent dispenser to avoid clogging its inlet and overflowing.
• Choose the right type of detergent for maximum washing efficiency with minimal water and energy consumption.
• For best cleaning results, it is important to dose the detergent correctly.
• Use less detergent if the drum is not fully loaded.
• Always adjust the amount of detergent according to water hardness; if your tap water is soft, use less detergent.
• Dose according to the level of soiling of your clothes; less dirty clothes require less detergent.
• Highly concentrated (compact detergent) requires particularly accurate dosing.

Signs of overdosing detergent include:

• Excessive foaming
• Poor washing and rinsing results

Signs of underdosing detergent include:

• Laundry becomes gray
• Formation of limescale deposits on the drum, heating element, and/or laundry

Control Panel

• 1. On/Off: Turn the appliance on and off.
• 2. Start/Pause: Start or pause a program.
• 3. Function: Select additional functions; the selected function lights up.
• 4. Programs: Select according to the type of laundry.
• 5. Display: Shows settings, estimated remaining time, parameters, and status messages.

Programs

Programs are presented for different types of laundry.

Attention! The parameters in this table are for user reference only. Actual parameters may vary.

Programs

Programs are presented for different types of laundry.

• Cotton: Durable textiles, heat-resistant textiles made of cotton or linen.
• Baby care with steam: Program for baby clothes, makes them cleaner, with more thorough rinsing to protect baby's skin.
• Quick wash 45': Program for a small amount of lightly soiled clothes.
• Mixed wash: Mixed load, consisting of cotton and synthetic textiles.
• Jeans: Special program for jeans.
• Quick wash 15': Very short program, suitable for washing lightly soiled laundry in small quantities.
• Spin: Additional spin with selectable speed.
• Rinse/Spin: Additional rinse with spin.
• ECO 40/60: Default 40°C, temperature setting is not selectable, suitable for laundry that can be washed at temperatures around 40°C - 60°C.
• Delicate/Silk: For delicate, washable textiles, such as silk, satin, synthetic fibers, or blended fabrics.

Possible Functions

Attention! For information on maximum spin speed, program duration, and other details of the ECO 40-60 program, please refer to the content in the "Technical Description" section. The table shows which cycle offers which setting options. Adjustment is not possible in the program itself.

Spin Speed

Possible spin speeds: 0-400-600-800-1000-1200

Additional Functions

• Pre-wash: Suitable for soaking laundry before the main wash program, suitable for stubborn stains. Detergent is recommended to be added to compartment I.
• Delayed start: You can delay the start of the program for 0-24 hours.
• Spin speed: Select spin speed.
• Additional rinse: Option to add an extra rinse cycle.
• Child lock: To prevent unwanted interference by children during the appliance's operation.

Attention!

• Press and hold the "Delayed start" and "Function" buttons for 3 seconds until you hear a beep to activate the function.
• Press both buttons for 3 seconds to deactivate the function.
• The "Child lock" will lock all buttons except the On/Off button.
• If you want to change the program in "Child lock" mode, first deactivate the lock, then turn the knob to OFF, and then you can select the desired program.

Maintenance

Cleaning and Care

!Warning! Always disconnect the appliance from the mains and close the water tap before cleaning and technical maintenance.

Washing Machine Cleaning

Proper maintenance of the washing machine can extend its service life. If necessary, the surface can be cleaned with diluted non-abrasive neutral detergents. In case of water overflow, wipe it immediately with a cloth. Never use sharp objects to clean the appliance.

Caution! Never use abrasive or corrosive substances, formic acid or its diluted solvents, or similar substances such as alcohol or chemical products.

Drum Cleaning

Any rust stains left inside the drum by metal objects must be removed immediately using chlorine-free detergents. Never use metal sponges to clean the drum!

Attention! Remove laundry from the drum while cleaning the washing machine.

Cleaning the Door Seal and Glass

Wipe the glass and seal after each wash to remove lint and stains. If lint accumulates, it may lead to leaks.

After each wash, remove all coins, buttons, and other items from the seal.

Clean the seal and glass every month to ensure normal operation of the appliance.

Cleaning the Inlet Filter

Attention! Reduced water flow is an indication that the filter needs cleaning.

1. Close the tap and disconnect the water inlet hose from it.
2. Clean the filter with a brush.
3. Unscrew the water inlet hose from the back of the machine. Pull out the filter using long-nosed pliers.
4. Clean the filter with a brush.
5. Reinstall the filter in the water inlet and reconnect the water inlet hose.
6. Clean the inlet filter every 3 months to ensure normal operation of the appliance.

Cleaning the Detergent Compartment

1. Press the button [] on the conditioner compartment lid and pull out the detergent compartment from the recess. Clean the inside of the recess with a brush.
2. Remove the conditioner lid from the dispenser compartment and rinse both items with water.
3. Reinstall the conditioner compartment lid and slide the drawer back into the recess.

Attention! Do not use abrasive or corrosive agents to clean plastic parts. Clean the detergent dispenser every 3 months to ensure normal operation of the appliance.

Cleaning the Drain Pump Filter

!Warning! Ensure the machine has completed the wash cycle and the drum is empty. Turn it off and unplug it before cleaning the drain pump filter. Be careful with hot water. Let the water cool down. Risk of scalding! Periodically clean the filter every 3 months to ensure normal operation of the appliance.

• Open the bottom cover.
• Open the filter by turning it counterclockwise.
• Remove foreign objects.
• Close the bottom cover.

Caution! During the appliance's operation and depending on the selected program, there may be hot water in the pump. Never remove the pump cover during the wash cycle; always wait for the appliance to complete the cycle and the drum to empty. When replacing the cover, ensure it is securely tightened.

Troubleshooting

Whenever a problem occurs with the appliance, check if you can solve it by following the tables below. If the problem is not resolved, please contact customer support.

Error Codes

!Warning! After checking, turn on the appliance. If the problem persists or other error codes appear on the display, contact the service department.

Repair

!Warning! Risk of electric shock

• Never attempt to repair a faulty or suspected faulty appliance. You may endanger your own life and the lives of future users. Only authorized specialists are allowed to perform these repair works.
• Improper repair will void the warranty, and subsequent damage cannot be claimed under warranty!

Moving

• Disconnect the appliance from the mains and close the water tap.
• Check if the door and detergent dispenser are properly closed.
• Disconnect the water inlet pipe and drain hose from the internal installations.
• Let all water drain from the appliance (see "Maintenance and cleaning of the drain pump filter").
• Important: Reinstall the 4 transport bolts on the back of the appliance.
• This appliance is heavy. Transport with care. Never hold any protruding part of the machine when lifting. The machine door must not be used as a handle.

Technical Specifications

Technical Description

Energy consumption 197 kWh/year, based on 220 standard cycles of the ECO program at 60°C and 40°C with full and half load, and low power mode consumption. Actual energy consumption will depend on how the appliance is used.

Energy consumption ECO 60°C with full load: 0.90 kWh/cycle

Energy consumption ECO 60°C with half load: 0.88 kWh/cycle

Energy consumption ECO 40°C with half load: 0.84 kWh/cycle

Energy consumption in off mode: 0.5 W

Energy consumption in standby mode: 1.0 W

Water consumption 10200 liters per year, based on 220 standard cycles of the ECO program at 60°C and 40°C with full and half load, and low power mode consumption. Actual energy consumption will depend on how the appliance is used.

Spinning energy efficiency class C

Maximum spin speed: 1200 rpm

Residual moisture content %: 62%

ECO 60°C and ECO 40°C standard wash programs, to which the technical data refers, these programs are suitable for washing normally soiled cotton laundry and are the most efficient in terms of energy consumption and water usage.

Program duration ECO 60°C with full load: 258 min

Program duration ECO 60°C with half load: 256 min

Program duration ECO 40°C with half load: 256 min

Standby mode duration: -

Spin noise level: 66 dBA

Spin noise level: 79 dBA

Possibility of built-in: no

1) Actual energy consumption will depend on how the appliance is used.

2) Actual water consumption will depend on how the appliance is used and water hardness.

Manufacturer Information

Country of origin – China.

Manufacturer: WUXI LITTLE SWAN ELECTRIC Co., Ltd., No.18 South Changjiang RD, New District, Wuxi, Jiangsu, China, 214000

Importer: LLC "Shmit Company" (INN/KPP: 9701028836/772201001, OGRN 1167746066509, Legal, actual, and postal address: 109052, Moscow, ul. Smirnovskaya, d. 25, str.12, kom. 07)

Organization authorized to accept claims from the buyer: LLC "Shmit Company" (INN/KPP: 9701028836/772201001, OGRN 1167746066509, Legal, actual, and postal address: 109052, Moscow, ul. Smirnovskaya, d. 25, str.12, kom. 07)

In case of a warranty claim, please contact authorized service centers. A list of authorized service centers in your city is provided in this user manual. If there is no authorized service center in your city, please contact the store where you purchased the item.

You can get information about service in your city by phone:

Hotline: 8 800 350 14 01

Service support: 8 (499) 113-42-42

WhatsApp: 8 (499) 281-65-87

And on the website www.schaublorenz.ru

Warranty period – 12 months

Service life – 5 years

Date of manufacture is indicated on the product

This information is part of the accompanying technical documentation provided with the product. The manufacturer is constantly working on improving the design and technical characteristics of the products manufactured. The manufacturer reserves the right to make changes to the design, equipment, and technical characteristics of the appliance without prior notice. The range of products manufactured is constantly updated and expanded, the information in this publication may change periodically.

After the service life, the equipment is not serviced, spare parts are not supplied, the authorized center has the right to refuse repair. Further operation may lead to the impossibility of normal use of the product. The product must be handed over to specialized companies that are engaged in the disposal of this type of product.

Packaging Disposal

The packaging is made of environmentally friendly materials that can be recycled, stored in special landfills, and disposed of without harm to the environment. Packaging materials have appropriate markings.

The used appliance must be rendered unusable. For this, disconnect the appliance from the mains and cut the attached cable, as it may pose a danger to playing children.

The symbol on the product or its packaging indicates that it is not to be disposed of as household waste. The product should be handed over to the appropriate collection point for electrical and electronic equipment for subsequent disposal. By observing the product disposal rules, you will help prevent environmental and human health damage caused by improper handling of such waste. For more detailed information on product disposal, please contact local authorities, waste disposal services, or the store where you purchased the product.

EAC CE