Waring Commercial CB15V One-Gallon Variable Speed Blender
Product Information
This document provides a detailed parts list and exploded view diagrams for the Waring CB15V One-Gallon Variable Speed Blender.
Unit Information:
- 3 Limited Motor Warranty
- 15.0 Amps
- 1,500-18,500 RPM's (no load)
Contact Information:
Waring Factory Service Center
314 Ella T. Grasso Ave.
Torrington, CT 06790
Tele: 1-800-269-6640
Fax: 860-496-9017
www.waringcommercialproducts.com
Exploded View - Page 1
The first page displays an exploded view of the blender's top and blending assembly components.
Key Components Illustrated:
- CBL10 Hot Blending Lid (optional)
- Blending Assembly (complete)
- Container with Blending Assembly
- Container Complete with Lid
- Container Complete with Stainless Steel Lid
- NSF Seal
Exploded View - Page 2
The second page shows an exploded view of the blender's base, motor, and control panel.
Key Components Illustrated:
- Top Housing
- Control Panel Assembly
- Motor with Sensor
- Brush Cap
- Brush & Spring Assembly
- Bottom Housing
- Feet
Parts List
The following tables detail the parts for the Waring CB15V blender.
Page 3 Parts List
| Illustration # | Part # | Description |
|---|---|---|
| 1 | 024000 | Outer Lid-polycarbonate for hot blending |
| 2 | 026496 | Gasket for plastic outer lid |
| 3 | 023998 | Baffle Cup for hot blending lid |
| 4 | 002972 | Cap Nut |
| 5 | 027581 | Washer-flat |
| 6 | 027683 | Blade |
| 7 | 018389 | "O" Ring |
| 8 | 027582 | Bearing Cap |
| 9 | 018390 | "V" Ring-small |
| 10 | 023934 | Bearing Holder |
| 11 | 004946 | Washer |
| 12 | 018386 | Bearing |
| 13 | 023926 | Spacer |
| 14 | 023907 | Spring Washer |
| 15 | 023927 | Retaining Ring |
| 16 | 023906 | "V" Ring-large |
| 17 | 023933 | Drive Shaft |
| 18 | 025817 | Key |
| 19 | 028530 | Cover Insert |
| 20 | 028226 | Outer Lid |
| 21 | 008791 | Latch Wire 3 Req.'d |
| 22 | 502773 | Bracket Assembly (spot welded to container 3 required) |
| 23 | 023909 | Double Handle Container |
| 24 | 502977 | Blending Assembly (complete) |
| 25 | 004949 | Gasket for container base |
| 26 | 025571 | Container Support (container base) |
| 27 | 012008 | Lock Nut |
| 28 | 503328 | Coupling |
| 29 | 025871 | Jar Pad |
| 30 | 028025 | Top Housing |
| 31 | 030201 | Control Panel Assembly |
| 32 | 029888 | Control Panel Rear |
| 33 | 026497 | Screw (4 required) |
Page 4 Parts List
| Illustration # | Part # | Description |
|---|---|---|
| 34 | 030453 | Control Panel Baffle |
| 35 | 002984 | Washer (4 required) |
| 36 | 016691 | Screw (4 required) |
| 37 | 503323 | Motor with Sensor |
| 38 | 018791 | Screen |
| 39 | 026500 | Screw (6 required) |
| 40 | 013731 | Cable Tie (5 required) |
| 41 | 026318 | Baffle |
| 42 | 018811 | Strain Relief |
| 43 | 503329 | Cord Set |
| 44 | 002943 | Washer for ground |
| 45 | 027278 | Screw for ground |
| 46 | 026317 | Bottom Housing |
| 47 | 002984 | Washer (4 required) |
| 48 | 026412 | Screw (4 required) |
| 49 | 026296 | Foot (4 required) |
| 50 | 018314 | Washer (4 required) |
| 51 | 026493 | Screw (4 required) |
Wiring Diagram
The wiring diagram illustrates the electrical connections for the blender's motor and control system, including the Hall Effect Sensor and potentiometer.
Diagram Description:
- The diagram shows connections from the motor to the control panel, including power input (Brown, Black, Blue wires) and sensor inputs (Red, Black, Green wires).
- It details the connections for the potentiometer and the AC line input.
