Assured Wireless – Assured WirelessCompatible Antennas – Assured Wireless
FirstNetMTU - AT&T IoT Devices
Installation Guide for ASSURED WIRELESS models including: AW12-DE MegaMobile, AW12-DE, MegaMobile
AW12 VEHICLE INSTALLATION KIT QUICK START GUIDE assured-wireless.com QSGmobile2022v1 Copyright ©2022 Assured Wireless Corporation. All rights reserved.
Support Link – Assured Wireless
File Info : application/pdf, 3 Pages, 517.78KB
DocumentDocumentMegaMobile Installation QUICK START GUIDE This quick start guide gives the basic steps for installing the AW12 MegaMobile unit in vehicles. 1 Ensure you have all the necessary equipment The following contents are included: AW12-DE modem AW12-PC-EI USB to Ethernet converter Vehicle mounting bracket (2) M6 screws and (2) M6 lock washers (4) M3 screws and (4) M3 lock washers Ethernet cable USB screwtight cable DC power cable (4-pin Molex) DC power cable (modem to Ethernet converter) SIM extractor tool You will also need the following (not included in your kit): GPS active/passive antenna LTE antenna (need 3 leads) Activated FirstNet micro SIM card Small Phillips head screwdriver Note. The antennas can be purchased as separate units or as a single unit. See our recommended antennas at assured-wireless.com/products/antennas. 2 Insert SIM card Note. Your distributor may have already inserted the SIM. If so, please skip to section 3. 1 Locate the SIM card slot on the side of the AW12 modem. 2 Remove the screw on the SIM slot door. 3 Use the depression on the upper left corner of the SIM slot door to open the door. You should now see the edge of the silver SIM tray. 4 Insert the included SIM extractor tool into the hole on the SIM tray; the tray should pop partway out. 5 Remove the SIM tray completely. 6 Insert your activated FirstNet SIM into the tray. Note that the tray is notched, so the card can only be inserted the correct way. 7 Re-insert the SIM tray into its slot. 8 Replace the SIM slot door and replace the screw, being careful not to overtighten. Align notch and insert in tray Copyright ©2022 Assured Wireless Corporation. All rights reserved. All information provided here is subject to change without notice. Assured Wireless and the Assured Wireless logo are property of Assured Wireless Corporation. assured-wireless.com QSGmobile2022v1 AW12 VEHICLE INSTALLATION KIT QUICK START GUIDE 3 Mount modem and Ethernet converter on bracket AW12 Modem USB to Ethernet Converter 1 Use the included M6 screws and washers and a Phillips #2 screwdriver to mount the modem to the mounting bracket. (Put the antenna ports to the edge as shown.) 2 Use the included M3 screws and washers to mount the USB to Ethernet converter to the mounting bracket. (Put the side with the ethernet port to the same edge as the modem antenna ports.) 4 Connect power and communication between modules Connect the USB-C to USB-A cable between the modem and the USB to Ethernet converter: 1 Insert the cable with the USB C connector. Insert it into the port labeled USB on the modem. and tighten the thumb screws. Be careful not to overtighten. 2 Insert the USB-A end of the AW12 Modem USB to Ethernet Converter cable into the port on the USB to Ethernet converter labeled Modem and tighten the thumb screw. Do not overtighten. Connect the short power cable: 1 Find the end of cable with the light green connector. Insert it into the port labeled PWR IN on the modem. Twist to tighten. 2 Insert the other end of the cable into the port on the USB to Ethernet converter labeled PWR OUT. 5 Mount bracket in vehicle Install the bracket in the vehicle with the proper hardware. Mount securely near the power source. Where and how you install the bracket will vary based on vehicle. Copyright ©2022 Assured Wireless Corporation. All rights reserved. All information provided here is subject to change without notice. Assured Wireless and the Assured Wireless logo are property of Assured Wireless Corporation. assured-wireless.com QSGmobile2022v1 AW12 VEHICLE INSTALLATION KIT QUICK START GUIDE 6 Install antennas 1 Install the antennas on the roof of the vehicle. For best performance, we recommend you keep at least one meter of separation between the antennas installed on the roof. 2 Connect the ends of the antenna cables into the four RF ports on the modem as follows: PRI port: LTE-1 cable B14 port: B14 cable DIV port: LTE-2 cable GNSS port: GPS/GNSS cable Note. See our antenna recommendations at assured-wireless.com/products/antennas. 7 Connect power and Ethernet cables 1 Insert the ethernet cable into the RJ-45 port labeled PoE+ on the USB to Ethernet converter and then connect the ethernet cable to the WAN port of your router. 2 Locate the DC power cable with the 4-pin Molex connector. Insert that connector into the port labeled PWR IN on the bottom of the USB to Ethernet converter, and then connect the unterminated ends of the DC power cable to the power source of the vehicle. 3 Refer to your router user manual for router configuration. Please make sure the MTU size setting in your router is 1342 or as otherwise advised at https://iotdevices.att.com/att-iot/FirstNetMTU.aspx. Antenna To router To vehicle power IGNITION BATTERY + NOT USED BATTERY - Note. If there is no ignition connection, be sure to connect the orange and red leads together. Copyright ©2022 Assured Wireless Corporation. All rights reserved. All information provided here is subject to change without notice. Assured Wireless and the Assured Wireless logo are property of Assured Wireless Corporation. assured-wireless.com QSGmobile2022v1