Electric Outboard Motor | ePropulsion
Instruction Manual for EPROPULSION models including: BEC4850 E Battery External Controller, BEC4850, E Battery External Controller, External Controller, Controller
4 days ago — RoHS 2.0 Directive(RoHS) 2011/65/EU and 2015/863EU. Applied Standards: EN IEC 61000-6-1:2019. EN 61000-3-3:2013 A1:2019 A2:2021. EN IEC 61000-3-2:2019/A1:2021.
Jan 27, 2025 — Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
This Controller is specially designed for E Battery and E Battery Solar Charger. Declaration of Conformity. We Guangdong ePropulsion Technology Limited, hereby, ...
File Info : application/pdf, 16 Pages, 3.13MB
DocumentDocumentE Battery External Controller Charge ON/OFF Mode Switch RUN 1 2 3 4 5 6 Charge BAT Control BAT 485 MODEL: BEC4850 Suitable for E Battery 2024.11 Version 1.3 Copyright © ePropulsion Technology Limited Introduction Thank you for purchasing ePropulsion E Battery External Controller. This Controller is specially designed for E Battery and E Battery Solar Charger. Declaration of Conformity We Guangdong ePropulsion Technology Limited, hereby, declares that this equipment is compliance with the applicable Directives and European Norms, and amendments. Object of the Declaration:Product: Product: E Battery External Controller Model: BEC4850 The object of the declaration is in conformity with the following directives: Electromagnetic Compatibility (EMC) 2014/30/EU RoHS 2.0 Directive(RoHS) 2011/65/EU and 2015/863EU Applied Standards: EN IEC 61000-6-1:2019 EN 61000-3-3:2013+A1:2019+A2:2021 EN IEC 61000-3-2:2019/A1:2021 EN IEC 61000-6-3:2021 Manufacturer Name: Guangdong ePropulsion Technology Limited Address: Room 801, Building 1, 11 Daxue Road, Songshan Lake, Dongguan, Guangdong Province, China Signature: Date: 2024.9.3 Shizheng Tao, Chief Executive Officer & Cofounder of Guangdong ePropulsion Technology Limited Statement Operation is subject to the following three conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with 1 the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Disposal and environment This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. 2 Interface description 245 Charge ON/OFF Mode Switch RUN 1 2 3 4 5 6 Charge BAT Control BAT 485 5.50 7.50 229 56 91 130 249 Specifications Voltage range Maximum current Weight Dimensions 41.6 - 57.6 VDC 50A 2300 g 245 x 130 x 91 mm Important Notes: According to research in the UK, the average amount of sunlight per day is around 2.5 hours. This can vary depending on location, but it's the overall average. Based on this, we recommend a minimum panel output of 250Wp per battery, with an optimal output of 400Wp or more per battery. Warning: Do not reverse the positive and negative poles of the External Controller. Before connecting the External Controller with the third party product, please contact ePropulsion authorized distributor. If the E battery is charged by the solar charger without a communication cable, it may not be fully charged to 100%. 3 Packing List Item E Battery External Controller E Battery External Controller Manual Qty. 1 pcs 1 pcs Operations Recommendation: Charge the system via shore power after every five cycles. Wiring Guide If you are unsure about wiring the system, do not attempt it yourself. Connect E40/E80/E175 Solar Panel Main Switch Charge ON/OFF Mode Switch Charge BAT Control BAT 485 AC Input Cable DC Output Cable Communication Cable CAN-IN MOTOR CAN-OUT CAN-IN MOTOR CAN-OUT 4 Connect E60/E163 Solar Panel Main Switch Charge ON/OFF Mode Switch Charge BAT Control BAT 485 AC input cable Communication cable For different E battery connections, you will need to purchase the following additional materials: Connection Item NO. Qty Note Battery Remote Switch 5m EB-AC02-01 1 To connect the remote Battery Comm Cable T Connector EB-AC05-00 1 switch, you need to prepare It is needed to connect the Remote Switch Extension Cable Without Resistance / 1 remote switch, which is included in the E Battery Solar Charger 48V 1600W Connect E Battery External Controller Comm Cable 00-0601-50 1 / E40/E80/ E175 Spirit/Navy Y Type Communication Cable 0.3m 00-0601-12 1 / Spirit/Navy Communication Cable 00-0601-01 1 / 0.5m 00-0601-28 Battery Bridging Cable 1.0m 00-0601-29 4 / 2.0m 00-0601-30 E Battery Communication Cable 1.5m 00-0601-10 1 / 5 Connection Item NO. Qty Note Battery Remote Switch 5m EB-AC02-01 1 Non-essential At least prepare 1pcs Battery Comm Cable T Connector EB-AC05-00 2 To connect the remote switch, you need to prepare 2pcs It is needed to connect the Remote Switch Extension Cable Without Resistance / 1 remote switch, which is included in the E Battery Solar Charger 48V 1600W Solar Charger communication Cable / 1 Included in the E Battery Solar Charger 48V 1600W E Battery Output Cable (Positive & Negative) 1.5m EB-CP04-00 1 / Connect E60/E163 Spirit/Navy Y Type Communication Cable 0.3m 00-0601-12 1 / Spirit/Navy Communication Cable 00-0601-01 1 / E battery charger DC output cable 1m 1m 00-0601-69 1 / 0.45m EB-CP01-00 / E Battery Bridging Cable (Positive & Negative) 1.5m EB-CP02-00 1 / 5.0m EB-CP03-00 / 0.5m EB-CP10-00 / Battery Communication Cable Kit 1.5m EB-CP11-00 2 / 5.0m EB-CP12-00 / 1. Connecting to E Battery, E Battery Solar Charger and NAVY. 2. For turning on the controller, please press and hold the power butto n on the controller for 1 second (no more than 3 seconds). In this case, the controller is in Standby Charge Mode by default. You can also turn on the system using the power button on the battery or the remote switch. In this case, the controller is in Mode 1 (No Control Mode) by default. 3. For switching modes of the controller, please press and hold the mode switch button on the controller for 1 second (no more than 3 seconds). 4. For turning off the controller, please press and hold the power button on the battery for 3 seconds, then the system will turn off automatically. 6 Modes · Mode 1 (No Control Mode) : For normal vessel operation. In this mode, the battery will charge and discharge at the same time. · Mode 2 (Standby Charge Mode) : Use this mode when the boat is left idle for more than one hour. It optimises battery charging. · For additional modes, please refer to the manual. LED Indicator RUN 1 2 3 4 5 6 ItemInmdeictahtoindg+Description RUN / The steady light is for the controller to work, the flash light is for the battery communication lost 1 No Control Mode Turn on the system using the power button on the battery or the remote switch. In this mode, the controller will not control the system. Keep the battery power on until the battery is fully charged and automatically turn off the battery, In this mode, when the charging current is less than 2A and 2 Standby Charge Mode exceeds 10 minutes, the controller will control the battery to shut down for 1 hour and then restart to detect the charging current. When the charging current is greater than 2A, the controller will keep charging. The system will shut down when the battery is fully charged. Standby Turn the battery on to discharge for 1 hour and then turn it 3 Discharge Mode off for 1 hour, repeating the cycle until the battery is less than A 10%. Standby Turn the battery on to discharge for 3 hours and then turn it 4 Discharge Mode off for 6 hours, repeating the cycle until the battery is less B than 10%. 7 Item 5 Indicating method Standby Discharge Mode C Description Turn the battery on to discharge for 6 hours and then turn it off for 12 hours, repeating the cycle until the battery is less than 10%. Standby Turn the battery on to discharge for 8 hours and then turn it 6 Discharge Mode off for 24 hours, repeating the cycle until the battery is less D than 10%. Notes If you want the battery to be fully charged and automatically shut down to save power, please switch to the Standby Charge Mode before leaving the boat. If you want the battery to automatically turn on and use electricity, please switch to the Standby Discharge Mode before leaving the boat. Warranty ePropulsion E Battery External Controller is guaranteed against any manufacturing defects for TWO years from date of delivery of products to end customers. Free warranty is only validated upon the presentation of legal serial number, Warranty Card, and evidence of purchase from an authorized ePropulsion dealer. Conditions Valid date of purchase should be established by the first-hand purchaser with original sales slip. Free warranty is not transferable and will not be reissued. The warranty is valid only when the information is correct and complete. Warranty does not cover Minor faults producing no influence on the intended function of the product. Faults resulting from any improper operation that contradicts the user manual. Accessories supplied with the product. Damage caused by accident, misuse or unauthorized repair. Damage caused by dropping, improper care or storage. If warranty expires, users can still enjoy maintenance services from ePropulsion authorized dealers with minimum maintenance charge. 8 WARRANTY CARD (*In order to validate warranty, please fill in this form first and read the Warranty Policies.) OWNER INFO. Owner Name Address Phone DEALER INFO. Store Name Address Phone PRODUCT INFO. Date of Purchase (mm/dd/yyyy) Serial No. Email Email Thanks for reading this user manual. If you have any concerns or find any problems while reading, please don't hesitate to contact us. We are delighted to offer service for you. Guangdong ePropulsion Technology Limited Webseite: www.epropulsion.com E-Mail: service@epropulsion.com