TOPDON V2200Air Jump Starter & Air Compressor

1 Safety

For your safety and the safety of others, and to avoid damage to the product and your vehicle, READ CAREFULLY AND ENSURE YOU FULLY UNDERSTAND ALL SAFETY INSTRUCTIONS AND NOTICES IN THIS MANUAL BEFORE OPERATION.

• ALWAYS WEAR APPROVED SAFETY GLASSES when working near a battery.
• Use ONLY the battery clamps supplied with this product.
• DO NOT use this product if the cable or the jump starter is damaged.
• DO NOT expose the product to direct sunlight or to places with high temperatures.
• DO NOT disassemble the product.
• DO NOT SMOKE OR HAVE A FLAME NEAR THE VEHICLE during testing. Fuel vapors and battery gases are flammable.
• Battery acid is extremely corrosive. If acid gets into your eyes, FLUSH THEM IMMEDIATELY WITH RUNNING COLD WATER FOR AT LEAST 20 MINUTES AND SEEK IMMEDIATE MEDICAL ATTENTION. If battery acid gets on your skin or clothing, WASH IT IMMEDIATELY WITH A SOLUTION OF WATER AND BAKING SODA.
• After this product is used for inflation, the nozzle will become very hot. DO NOT touch the nozzle directly to prevent burns.
• It is recommended to wait three to five minutes between each use of this product for inflation.
• This product comes with a built-in battery. It is recommended to charge it at least every six months.
• Do not leave this product in the car under any circumstances during the day or summer. Due to the heat, it may affect the battery and damage it, which may lead to swelling or even explosion of the battery.
• The storage temperature of the product is between -20°C and 55°C.
• The operating temperature of the product is between -10°C and 55°C.
• A closed car in the sun can have an internal temperature much higher than the outside and can reach over 90°C. Therefore, do not leave the product in a closed and hot place under the sun.

2 What's in the Box?

• V2200Air
• Smart Clamp Booster Cable
• Inflation Nozzle
• Inflation Needle
• USB-C to USB-C Cable
• User Manual

3 About the V2200Air

The V2200Air Jump Starter & Air Compressor is a 2-in-1 device that can help jump-start 12V lead-acid battery vehicles and inflate tires of vehicles, sports balls, or other items. It features high-lumen LEDs that can function as a flashlight with SOS and strobe functions. It can also serve as a power bank for charging phones, tablets, and other electronic devices.

3.1 Jump Starter and Air Compressor

Diagram showing the V2200Air unit with numbered parts:

• 1. Input/Output Ports: USB-C input/output port (x1), USB-A output port (x1), DC output port (x1)
• 2. Jump Start Port
• 3. Carrying Handle
• 4. LED Flashlight
• 5. Screen

The screen displays various icons:

• Jump Start Mode: Default mode for jump-starting vehicles.
• Car Inflation Mode: For inflating car tires.
• Motorcycle Inflation Mode: For inflating motorcycle tires.
• Bicycle Inflation Mode: For inflating bicycle tires.
• Sports Ball Inflation Mode: For inflating basketballs, footballs, etc.
• Custom Inflation Mode: Allows setting a custom pressure.
• Constant Pressure Inflation Mode: Maintains a set air pressure, automatically stopping when the target is reached and resuming if it drops below 5% of the target.
• Air Pressure Value: Displays the current air pressure in PSI, BAR, or KPA. This icon is only active in inflation modes.

Exceptions:

• Overheating Icon (Thermometer Symbol): Indicates the V2200Air has overheated and will resume normal temperature after stopping operation.
• Short Circuit/Reverse Polarity Icon (Exclamation Mark in Triangle): Indicates a short circuit or reverse polarity.
• General Exception Icon (Exclamation Mark in Circle): Indicates an exception other than the above two.

Battery Charge Level: Four levels indicating 25%, 50%, 75%, and 100% charge.

6. Buttons

• Power Button (◼): Press to turn on the V2200Air. Press and hold for 3 seconds to turn the LED flashlight on/off. Press and hold for 7 seconds to turn off the V2200Air (it will auto-off after 20 seconds of inactivity).
• Mode Button (M): Press to cycle through 6 working modes. Press and hold for 1.5 seconds to switch between 3 air pressure units. In inflation mode, press to start or stop inflation.
• Plus/Minus Buttons (+ / -): Press to increase or decrease the air pressure value.

3.2 Smart Clamp Booster Cable

Diagram showing the smart clamp booster cable with numbered parts:

• 1. Unit Readiness Indicator: Solid green light indicates the jump starter is ready for use.
• 2. Error Indicator: Solid red light indicates reverse polarity, short circuit, overheating, or incorrect connection. A buzzer will also sound. If the unit is connected correctly but neither indicator lights up, the battery voltage may be below 3V. Try using BOOST mode.
• 3. BOOST Button: Press to activate BOOST mode. The unit readiness indicator will turn green. Start the vehicle within 30 seconds. BOOST mode automatically deactivates after 30 seconds or if the vehicle is not started successfully. Note: All safety protections are temporarily disabled in BOOST mode. Use with caution and only after the traditional jump-start method has been attempted.
• 4. Positive Clamp (Red)
• 5. Negative Clamp (Black)

4 Instructions for Use

4.1 Charging the V2200Air

Note: The V2200Air must be fully charged before use.

Charge the V2200Air via the USB-C port. Connect one end of the USB-C to USB-C cable to the USB-C port and the other end to a USB-C port electrical outlet or a power adapter (not included).

4.2 Turning on the V2200Air

Press the ◼ button to turn on the V2200Air.

Note: The V2200Air will automatically turn off if there is no activity within 20 seconds.

4.3 Jump-Starting a Vehicle

Note: The V2200Air can only be used to jump-start vehicles with 12V lead-acid batteries.

The V2200Air offers two modes: Jump Start and BOOST.

4.3.1 Jump Start Mode

1. Connect the V2200Air and the vehicle's battery using the smart clamp booster cable. The blue connector plugs into the V2200Air's jump start port. The red and black clamps connect to the positive (+) and negative (-) battery terminals, respectively.

NOTE: When the V2200Air detects the connection to the vehicle's battery, the Jump Start mode icon will be constantly lit on the screen. If the readiness indicator on the clamp cable turns solid green, you can start the vehicle. If the readiness indicator does not light up continuously green, the voltage between the clamps is below 3V, and the vehicle will not start successfully. You can try BOOST mode.

2. Start the vehicle within 30 seconds.
3. Disconnect the smart clamp booster cable from the vehicle's battery once the vehicle starts.

NOTE: If the vehicle fails to start, please disconnect the clamps from the battery. You can try again after 20 seconds. It is strongly recommended not to attempt jump-starting more than three times within two minutes.

4.3.2 BOOST Mode

If the vehicle fails to start in Jump Start mode, it may be because the voltage between the clamps is lower than 3V. You can try BOOST mode.

IMPORTANT: In BOOST mode, the V2200Air will output automatically for 30 seconds. Never directly connect the positive starting clamp to the negative one in this mode. Otherwise, a strong current may cause damage, injury, or even death.

Operation in BOOST mode is similar to Jump Start mode. You need to press the BOOST button on the smart clamp booster cable to activate BOOST mode.

4.4 Using the V2200Air for Inflation

Note: Please ensure you know the required air pressure for the object to be inflated beforehand.

1. Turn on the V2200Air and press the M button to select one of the six inflation modes.
2. Press and hold the M button for 1.5 seconds to select one of the three air pressure units.
3. Press the + and - buttons to set the target air pressure value.
4. Assemble the supplied inflation nozzle and needle with the inflation hose, then connect the hose to the object that needs inflation.
5. Press the O button to start inflation.

Notes:

• During inflation, the real-time air pressure of the object will be displayed on the V2200Air screen. When it reaches the set target air pressure, the V2200Air will stop inflating automatically.
• During inflation, press the O button to stop it manually if needed.

Recommended Pressure Ranges for Use

4.5 Using the LED Flashlight

The V2200Air has an LED flashlight. Once turned on, press and hold the ◼ button for 3 seconds to turn it on.

The LED flashlight also offers light signal and SOS functions. You can press the ◼ button to switch between them.

To turn off the LED flashlight, press and hold the ◼ button for 3 seconds.

4.6 Using the V2200Air as a Power Bank

The V2200Air can be used as a power bank to charge phones, tablets, and other electronic devices.

Turn on the V2200Air and connect it to an electronic device via the USB-C input/output port.

4.7 Turning off the V2200Air

Once the V2200Air is turned on, press and hold the ◼ button for 7 seconds to turn it off.

Note: Once turned on, the V2200Air will automatically turn off if there is no activity within 20 seconds.

5 Technical Specifications

• Model: V2200Air
• Peak Current: 2200A
• Battery Capacity: 3.7V, 12000mAh; 44.4Wh
• USB-C Input/Output: PD45W, 5V=3A, 9V=3A, 12V=3A, 15V=3A, 20V=2.25A
• USB-A Output: 5V=3A
• DC Output: Max. 16.8V = 10A

6 Warranty

One-Year Limited Warranty from TOPDON

TOPDON warrants to the original purchaser that its products will be free from defects in material and workmanship for a period of 12 months from the date of purchase (warranty period). For defects reported during the warranty period, TOPDON will repair or replace the defective part or product according to its analysis and confirmation from technical support. TOPDON is not responsible for any incidental or consequential damages arising from the use, misuse, or installation of the device. If there is any conflict between TOPDON's warranty policy and local laws, local laws shall prevail.

This limited warranty is void under the following conditions:

• Used for purposes other than intended, disassembled, modified, or repaired by unauthorized shops or technicians.
• Negligent handling and violation of operation.

Note: All information in this manual is based on the latest available information at the time of publication and cannot be guaranteed for accuracy or completeness. TOPDON reserves the right to make changes at any time without notice.