User Manual for SC T models including: HKM02BP-4K, 4K HDMI KVM USB RS232 IR Audio over PoE Extender
Smart Cabling & Transmission Corp. V1.0 2010160 AV over IP Extender User Manual Model : HKM02BP-4K 4K HDMI KVM & USB, RS232 , IR, Audio over PoE Extender
Smart Cabling & Transmission Corp. V1.0 2010160 AV over IP Extender User Manual Model : HKM02BP-4K 4K HDMI KVM & USB, RS232 , IR, Audio over PoE Extender
File Info : application/pdf, 35 Pages, 2.43MB
DocumentDocumentAV over IP Extender User Manual Model : HKM02BP-4K 4K HDMI KVM & USB, RS232 , IR, Audio over PoE Extender Smart Cabling & Transmission Corp. V1.0_2010160 User Manual HKM02BP-4K Introduction HKM02BP-4K uses AV over IP technology to route up to 1,000 4K HDMI sources to up to 60,000 displays over IGMP and Jumbo frame protocol gigabit PoE switches, which can achieve HDMI signal extending, distributing, switching and routing. Additionally, the boundless switching function allows you to use one mouse to operate multiple PCs by moving the mouse cursor across the monitors' borders. HKM02BP-4K is a multifunctional system that integrates multiple media. You can perfectly apply it to large-scale security rooms, classrooms, trading rooms, and many more. Features Resolution up to 4K@30Hz 4:4:4 Signal extension up to 150M over CAT5e (or greater), 60KM over fiber optic cable. Workable with PoE switches for HDMI extension, distribution, switching, and matrix. Built-in loop out, an extra local HDMI display at TX side. Built-in 4 USB ports for keyboard, mouse, flash drive...etc. Supports up to 8 x 16 video wall. Supports video scaler, 4K to 1080p/ 1080p to 4K. Supports HDMI audio embedding and extraction function. Supports USB, full-duplex RS232, bi-directional IR, analog audio transmission. Supports RS232 signal distribution. Workable with SR01X (IP repeater) for longer distance. Managed via Windows based software, Android/iOS APP, Web GUI, IR remote, panel pushbutton, Telnet API, RS232 console. 1 Installation view User Manual HKM02BP-4K 2 Panel view HKM02BT-4K HKM02BR-4K User Manual HKM02BP-4K Panel Button Function Button - + Menu Short Press Reduce Number Increase Number Enter Menu/Cancel Press 1 seconds Press 3 seconds Carry Decomposition Lock/Unlock Button(When no OSD menu) Press and hold then power on Factory Default Engineering Mode Set Factory Default then enter Engineering Mode Reduce Number: switches channel or function number down Increase Number: switches channel or function number up Carry: shifts the three numbers in display one position to the left Decomposition: shifts the three numbers in display one position to the right In engineering mode Power and Link LED will be flash together, IP address of unit will be set to Static IP 192.168.0.88 temporarily, users can login to the web page by browser to update firmware. Front Panel LED Indication Panel LED Status HKM02BP-4K On Boot completed Power (Green) Flash Twice Flash Slowly Booting Transmitter: stop link Receiver: video output be turned off Breathing(Fading) Screen saver mode (not available for transmitter) Link(Blue) On Flash Connected & video is streaming Connecting, or no source input from transmitter IR(Red) On Transmitting /receiving IR signal UTP On Connected by UTP RJ45 port (Green) Flash Transmitting /receiving data from UTP RJ45 port SFP(Blue) On Flash Connected by Fiber SFP port Transmitting /receiving data from Fiber SFP port MSG(Red) On Flash 2~9 Times Other message (IR, RS232, System setting...) System warning, Alert (Refer to MSG/IR Status Indication) 3 MSG/IR LED Status Indication Times Always ON 2 3 4 5 6 7 8 9 10 HKM02BP-4K MSG LED IR control, RS232 control, system setting IR control disabled Transmitters channel conflict DHCP server not found Rest to factory default Engineering mode / Firmware update mode Manufacture setting mode Aux system stopped Aux system firmware boot sector error Aux system firmware type error RJ45 LED Indication RJ45 LED LINK (Green) ACT (Orange) Status On Flash Description Ethernet connected Data transmission User Manual HKM02BP-4K RJ45 Pin Define Video Link (TIA/EIA-568-B) 1. Orange-white DATA0 + 2. Orange DATA0 - 3. Green-white DATA1 + 4. Blue DATA2 + 5. Blue-white DATA2 - 6. Green DATA1 - 7. Brown-white DATA3 + 8. Brown DATA3 Cable & Transmission Distance Link Cable use high quality CAT.5e UTP/STP/FTP or CAT.6 UTP cable Transmission distance will be affected by equipment (Switch HUB), cable quality...etc. When using CAT.5e/CAT.6 cable connect transmitter and receiver directly without Ethernet switch, the maximum transmission distance up to 150M. You can also use model no: SR01X repeater for extended longer distance or using Gigabit Switch hub which support IGMP protocol and Jumbo Frame 8K for signal distribution or extend distance. 4 User Manual HKM02BP-4K System Default Casting Mode/IP Settings Casting Mode Transmitter / receiver support Unicast and Multicast two mode, default is Multicast. In Multicast mode it could be one to one, one to multi, multi to on or multi to multi applications. The analog audio output of transmitter and input of receiver will be off in this mode, analog audio only from transmitters send to receivers. Unicast mode suitable for one to one or multiple transmitters to one receiver applications. Analog audio bi-direction transmission only in Unicast mode. IP Mode System default IP setting is Static IP, IP mapping to last 4 digits of MAC address (Hex), for example MAC XX:XX:XX:XX:12:AB, the IP address will be169.254.18.171 You could also set to DHCP or Auto IP, please refer to web setting chapter: IP Setting: Page 18. In Auto IP mode it will assign 169.254.X.X (subnet mask 255.255.0.0) to transmitters and receivers without DHCP server. We recommend Static IP mode when using APP or PC software control to prevent any IP change problem. Bandwidth Chart The bandwidth will be varied based on different resolution. Higher resolution may not request bigger bandwidth. Below Chart is the resolution and bandwidth status for reference. Resolution (@60Hz) 3840x2160 (2160p) 1920x1080 (1080p) 1280x720 (720p) 1600x1200 (UXGA) Average Bandwidth (Mbps) Resolution (@60Hz) 218 (146~268) 1280x1024 (SXGA) 133 (80~210) 1024x768 (XGA) 147 (112~177) 800x600 (SVGA) 81 (57~105) 640x480 (VGA) Average Bandwidth (Mbps) 113 (79~150) 81 (72~120) 66 (49~82) 43 (29~56) Above bandwidth chart not include USB transmission, it cost up to 50 Mbps when transferring mass data. System scalability is limited only by uplink and stacking connector bandwidths, for example under Gigabit Ethernet network, the total flow must not exceed 1000Mbps to avoid any delay on video streaming. If the video play with 1080p resolution, the transmitter allow maximum up to 7 pcs for simultaneous video streaming. For 8~16 sources: use switches which support 802.3ad Link Aggregation or smart (or intelligent) switches to get 2 Gbps or more bandwidth. For over 16 sources: use switches which support SFP+ uplink or stackable switches to get 10 Gbps bandwidth. 5 User Manual HKM02BP-4K IR Remote Control Setting You could use the IR infrared remote control to preset channel selection and other menu function. Using the IR remote control aim to the front panel of receiver or external IR receiver cable will be ok. Initial at first time use the remote control or after change battery of remote control, the IR remote control and the equipment Remote ID must be using same ID. The default Remote ID for transmitter is 7, for receiver is 8. To setting the Remote ID, Press and hold power button, then press button 8 to complete the setting. + . ( without transmitter or receiver) IR Remote Control Button Symbol Button POWER MENU UP DOWN LEFT RIGHT ENTER ASTERISK NUMBER A B 1 2 3 4 5 6 7 8 9 0 Receiver Function Transmitter Function Turn Off/On Video Output Connect/Disconnect Receiver Setup Remote Control ID Menu selection, input numbers after press menu button Increase Value Reduce Value Carry Decomposition Enter / Show Channel Information (When no other Menu operation) Cancel Enter Recall Previous Value Favorite Channel Switching Set RS232 to Auxiliary Mode to Receive Menu Message Back to Previous Channel Set RS232 to Extender Mode Number 1 Number 2 Number 3 Number 4 Number 5 Number 6 Number 7 Number 8 Number 9 Number 0 6 User Manual HKM02BP-4K IR Remote Control Operation Select Channel: Mode 1: use or or or to select channel and press ENTER to confirm. Mode 2: enter the channel number and press ENTER to confirm the input channel. Select Menu Function: Mode 1: press MENU then use or or or to select function, press ENTER to confirm. Mode 2: press MENU, then input function number as below, press ENTER to confirm. Wake Up Receiver: In screen saver mode (30 seconds without video input), press any button of IR remote/pane to wake up Connect /Disconnect Connection for Transmitter: Press POWER of IR remote to connect/discount connection. Turn On/Off Video Output for Receiver: Press POWER of IR remote to turn on/off monitor, press panel button CH- and CH+ together to turn on IR Quick Block for Receiver: # # #: IR block mode, ignore IR control signal until press any panel button or IR remote * three times * * * : Quit IR block mode TV Wall Quick Switch for Receiver: MENU+POWER: Switch between TV Wall/Single monitor modes immediately. Add Favorite List for Receiver: MENU+A: Add channel to favorite list in menu, maximum 32 channels. Remove Favorite List for Receiver: MENU+B: Remove current channel from favorite list in menu Set RS232 Mode for Transmitter: MENU+A: Switch to message mode to receive response instead of OSD. MENU+B: Switch to extender mode. 7 IR Menu Function List No. Menu 0 System Information 1 Network Information 2 Function Information 3 Control Information 4 Video & Audio Information 5 RS232 Control Information 6 Channel Information 7 Favorites Information 8 Routing Information 9 Video Wall Information 10 Advanced Menu 11 Reconnection 12 Disconnection 13 Stop Connection 14 Starting USB 15 Casting Mode 16 Jumbo Frame 17 Free Routing 20 Video Function 21 Audio Function 22 USB Function 23 RS232 Function 24 IR Function 25 Video Wall Function 27 Keyboard Mouse Function 30 Button Control 31 Button Lock 32 IR Control 33 IR Control ID 34 RS232 Control 35 HDMI 5V Control 37 Rotary Switch 41 Scaler Output Mode 42 Audio Select Description System Information Network Information Function Information Control Information Video & Audio Information Option / Remark RS232 Control Information Channel Information Favorites Information Routing Information Video Wall Information Display advance menu Reconnect with TX/RX Disconnection (keep routing channel) Stop all connection (Include routing channel) Get USB control priority (in multicast mode only) Casting Mode setting Jumbo Frame setting Free Routing setting Video Extender setting Audio Extender setting USB Extender setting RS232 Extender setting IR Extender setting 0 = Hide 1 = Display 0 = Unicast 1 = Multicast 0 = Disable 1 = Enable 0 = Disable 1 = Enable Video Wall setting Keyboard Mouse Extender setting Button Control setting Button Lock IR Control setting IR Control ID setting RS232 Control setting Cut HDMI 5V when switching HKM02BT Channel Switch Video output resolution setting TX Audio Input Select /RX Audio Output Select 0 = Disable 1 = Enable 0 ~ 9 = IR Control ID 10 = User Define Controller 0 = Disable 1 = Enable (Case Sensitive) 2 = Case Insensitive 0 = Disable 1 = Enable 0 = Pass-Through 1 = Pass-Through (Strict) 2 = Auto Detect (Per EDID) 3 = Full HD 1080p 60Hz 4 = Full HD 1080p 50Hz 5 = Customize 0 = Digital 1 = Analog User Manual HKM02BP-4K RX TX V V V V V V V V V V V V V X V X V X V X 1 1 V V V X V V V X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 1 1 8 7 1 1 0 X X 1 0 X 2 2 8 User Manual HKM02BP-4K 2 = Auto 43 Analog Input Volume 44 Analog Output Volume Analog Input Volume Analog Output Volume 0 = Mute 1 ~ 100 = Volume % 45 Video Quality Video Quality setting 0 = Graphic Mode 1 ~ 5 = Mode 1 ~ 5 6 = Video Mode 46 Anti-Dither Anti-Dither setting 0 = Disable 1 ~ 2 = Mode 1 ~ 2 47 EDID Update Update EDID from TX or monitor of RX 48 EDID Select 49 HDCP Always On Select default EDID of TX HDCP setting 0 = Default HDMI 1 = Default DVI 2 = Default VGA 3 = Loopout Monitor (HKM02B Only) 0 = Disable 1 = HDCP 1.4 Always On 2 = HDCP 2.2 Always On 50 RS232 Select RS232 Port Mode Select 0 = Disable 1 = Extender 2 = Keypad 3 = Auxiliary 4 = Console 51 RS232 Baudrate RS232 Extender Baudrate 0 = 115200 bps 1 = 57600 bps 2 = 38400 bps 3 = 19200 bps 4 = 9600 bps 5 = 4800 bps 6 = 2400 bps 7 = 1200 bps 8 = 600 bps 9 = 300 bps 52 RS232 Newline 53 RS232 Trigger RS232 Control Newline setting RS232 Control Trigger setting 0 = Linux (0x0A) 1 = Windows (0x0D, 0x0A) 2 = Mac (0x0D) 3 = Other (0x0A, 0x0D) 54 Auxiliary Baudrate Auxiliary Baudrate 0 = 115200 bps 1 = 57600 bps 2 = 38400 bps 3 = 19200 bps 4 = 9600 bps 5 = 4800 bps 6 = 2400 bps 7 = 1200 bps 8 = 600 bps 9 = 300 bps 55 Auxiliary Newline 56 Auxiliary Trigger Auxiliary Newline setting Auxiliary Trigger setting 0 = Linux (0x0A) 1 = Windows (0x0D, 0x0A) 2 = Mac (0x0D) 3 = Other (0x0A, 0x0D) 57 Device No Device No. for RS232 control 0 ~ 999 58 Group No 59 Party No Group No. for RS232 control Party No. for RS232 control 0 ~ 99 60 Fast Switch 61 Conflict Check Switch without stop link Check existing TX channel 0 = Disable 1 = Enable 62 Channel Name Display Channel Name 0 = Hide 1 = Display 63 Only Favorites 64 Lock Favorites Only Favorites Channel Available Lock Favorites Channel 0 = Disable 1 = Enable 9 85 85 85 85 X 6 X 0 V V X 1 0 0 1 1 0 0 1 1 1 1 0 0 1 1 1 1 0 X 0 X 0 X 1 1 X 1 0 X 0 X 0 X User Manual HKM02BP-4K 65 Auto Sort Favorites 66 Sort Favorites 67 Scan Channel To Favorites 70 Direct Access Menu 71 Menu Item "Advanced Menu" 72 Screensaver 73 Screen Off Option 74 Diagnostic Information 75 Message Redirect 76 Command Redirect 80 Video Routing 81 Audio Routing 82 USB Routing 83 RS232 Routing 84 IR Routing 86 GPIO Routing 87 Load Routing Mapping 88 Save Routing Mapping 90 Video Wall Max Row 91 Video Wall Max Column 92 Monitor Row Position 93 Monitor Column Position 94 Monitor Outside Width 95 Monitor Outside Height 96 Monitor Viewable Width 97 Monitor Viewable Height 100 Stretch Type 101 Rotate 102 Vertical Shift 103 Horizontal Shift 104 Vertical Scale 105 Horizontal Scale 106 Load Video Wall 107 Save Video Wall 200 Backup Setting 201 Restore Setting 202 System Setting 203 Application Setting 333 Reset To Default 400 Preset Configuration 999 System Reboot Auto Sort Favorites Channel Sort Favorites Channel Immediately sort favorite channel 0 X V X Scan Channel To Favorites V X Run menu function even hide 1 1 Display/Hide "Advanced Menu" Screen Saver setting 0 = Disable 1 = Enable 1 1 0 X Behavior After Screen Off 0 = No Option 1 = Mute Analog Audio 2 = Stop Connection 1 X Diagnostic Information Message Redirect to Auxiliary Command Redirect to Auxiliary 0 = Disable 1 = Enable 1 X X 1 1 1 Video Routing setting 1000 X Audio Routing setting 1000 X USB Routing setting RS232 Routing setting 0 ~ 999 = Specific Channel 1000=Follow Channel 1000 X 1000 X IR Routing setting 1000 X GPIO Routing setting 1000 X Load Free Routing Mapping Save Free Routing Mapping 0~3 V X V X Rows of Video Wall(Vertical) Columns of Video Wall(Horizontal) 0~7 (0=row 1, 1=row 2...) 0~15 (0=column 1, 1=column 2) 0 X 0 X Monitor Position in Row 0~7 0 X Monitor Position in Column 0~15 0 X Outer Width of Monitor Outer Height of Monitor Width of Viewable Area 0~65000 (0.1mm) 0 X 0 X 0 X Height of Viewable Area 0 X Screen Stretch Type 0 = Auto 1 = Stretch Out 2 = Fit In 2 X Screen Rotation and Mirror 0 ~ 7 0 X Screen Vertical Shift 400 = Default 399 ~ 0 = shift up 401 ~ 801 = shift down 400 X Screen Horizontal Shift 400 = Default 399 ~ 0 = shift left 401 ~ 801 =shift right 400 X Screen Vertical Scale Screen Horizontal Scale 0 ~ 255 0 X 0 X Load Video Wall Setting Save Video Wall Setting 0~15 V X V X Backup Setting to bank 0~3 Restore Setting from bank 0~3 0 ~ 3 V V V V System Setting Application Setting 0~255 (Debug use, no recommend for general users) V V V V Reset to factory default V V Set RX Group ID 0 ~ 15 (OEM Version only) V X System Reboot V V V = Available X = Not available Numbers = default value 10 User Manual HKM02BP-4K Caution of IR Menu Function Menu 17 Free Routing function only works in Multicast mode. Menu 22 When disable USB extender function it will also disable keyboard mouse function. Menu 25 Display or hide TV wall setting in the webpage. Menu 27 You could disable keyboard mouse extender if any compatible issue, it will use USB extender instead of keyboard mouse extender. Menu 33 To set customize IR remote, need to be import to RX by RS232 or Telnet command Menu 35 For monitors which detect HDMI 5V to enter sleeping mode. Menu 36 Turn off monitor by CEC command via RX. Menu 41 Pass-Through means output resolution follow TX EDID, Auto Detect(Per EDID) means output resolution follow monitor EDID of RX, Customize resolution need to be setup by RS232 command or web page Menu 47 Use default EDID at TX side, or copy monitor EDID at RX side. (In multicast mode) Menu 49 Monitor HDCP version setting, with incorrect HDCP version setting it will show HDCP fail on black screen. Option Description Disable HDCP version follow source and Stream Type of content HDCP 1.4 Always On Monitor support HDCP 1.4 HDCP 2.2 Always On Monitor support HDCP 2.2 Menu 50 Extender = RS232 extender, Keypad = for RS232 keypad or number key in terminal software, Auxiliary = auxiliary mode debug, Console = system console debug Menu 60 Fast Switch mode works best when: resolution, frame rate, scan mode (interlaced/non-interlaced), color depth, color space, interface (HDMI/DVI), HDCP mode (ON/OFF) all above are the same. Disable: Stop link before channel switch, is will show black screen between switching, if switch to the channel which not exist it will show diagnostic Information. Enable: Keep link when channel switch, if switch to the channel which not exist may cause screen freeze 1~2 seconds then show diagnostic Information. Menu 61 Conflict Check will check TX channel number at booting, reconnection and before switching, if channel number already existed the connection will be interrupted. Menu 62 Channel Name will show full name instead of number only, the position of channel name is center of screen. Channel name can set by RS232 command or import from telnet port. Menu 75 Message Redirect forward MENU message to TX RS232 port (Auxiliary mode) instead of OSD. Menu 76 Command Redirect run RS232 command from Web or telnet port (Auxiliary mode). Menu 80~86 Fix selected function not follow the channel, only available when free routing enabled. Menu 90~107 Only available when video wall function enabled.. 11 User Manual HKM02BP-4K Menu 200 Will not backup the parameters of men function 107 Save Video Wall. Menu 333 Will clear the parameters of men function 107 Save Video Wall. RS232 Control In RS232 extender mode, user could use RS232 port of transmitters to operate/setup the receivers at same channel by program like Hyper Terminal which built-in Windows XP and before version. Hyper Terminal setting: 115200 bps (8-N-1), Flow control: None(Properties -> Settings -> ASCII Setup... and select "Send line ends with line feeds" &"Echo typed characters locally") We recommend set the RS232 routing for all receivers to one transmitter to avoid RS232 connection broken by video channel switching. Command format: >CMD_Address> Command Parameters Address, command and parameters are char, not hex code Enter (LF or CR+LF) is required to execute the command All accord receivers will run the command and parameters, we also add 3 kinds of user defined numbers except MAC & IP (Device No, Group No, Party No) for flexible application: Mxxxxxx Ixxxx Dxxx Gxx Pxx Cxxx ALL TX RX The last 6 digits of MAC Address of receiver e.g.: 2218688612AB = M8612AB The last 2 column of IP Address (HEX) of receiver e.g.: 169.254.012.034 = I0C22 Device No e.g.: Device No 123 = D123 Group No e.g.: Group No 12 = G12 Party No e.g.: Party No 34 = P34 Channel No e.g.: Channel 123 = C123 All receivers Transmitter which connected to RS232 port currently. Receiver which connected to RS232 port currently.(for Auxiliary mode) Response format: <ACK_Address< Response character Receivers will response message to transmitter as above format and send Newline after When send command to multiple receivers(address as Gxx, Pxx, Cxxx, and ALL) they will not response. Example: >CMD_M8612AB> CHANNEL 12 (Set receiver which last 6 digits MAC Address is 8612AB to Channel 12) <ACK_M8612AB< OK (Receiver which last 6 digits MAC Address is 8612AB response "OK") RS232 Command and Parameters List Command CHANNEL Parameters ? [ 0~999 ] [ 0~999 ] NAME ? [ 0~999 ] NAME "string" NAME ? NAME [ ENABLE | DISABLE ] Description Show current channel number Switch to specified channel Check current channel name Set channel name, 28 character MAX Show channel name setting Enable/disable channel name Remark Transmitter not support parameter NAME Receiver not support parameter CHECK 12 FAVORITE VIDEO NAME CLR NAME IMPORT FAST ? FAST [ ENABLE | DISABLE ] CHECK ? CHECK [ ENABLE | DISABLE ] ? ADD ADD [ 0~999 ] DEL DEL [ 0~999 ] CLR ONLY ? ONLY [ ENABLE | DISABLE ] AUTO ? AUTO [ ENABLE | DISABLE ] SORT FUNC ? FUNC [ ENABLE | DISABLE ] ROUTING ? ROUTING [ FOLLOW | 0~999 ] SELECT ? SELECT [ 0~2 ] SCALER ? SCALER [ 0~4 | 5] CUSTOMIZE ? CUSTOMIZE integer QUALITY ? QUALITY [ 0 | 1~5 | 6 ] DITHER ? DITHER [ 0 | 1~2 ] EDID RESUME PAUSE BLACK FUNC ? FUNC [ ENABLE | DISABLE ] MODE ? MODE [ ENABLE | DISABLE ] LOAD 0~15 LAYOUT 0~15 VIDEOWALL 13 SAVE 0~15 OW ? OW [ 0~65535 ] OH ? OH ? [ 0~65535 ] VW ? VW ? [ 0~65535 ] VH ? VH ? [ 0~65535 ] MAX_ROW ? MAX_ROW 0~7 MAX_COLUMN ? MAX_COLUMN [ 0~15 ] ROW? ROW [ 0~7 ] COLUMN ? User Manual HKM02BP-4K Clear all channel name Import channel name Status of current fast switch Enable/disable fast switch Status of channel conflict check Enable/disable channel conflict check Usage of favorite channel (MAX.32) Add current to favorite channel Add specified channel to favorite Delete current from favorite channel Delete specified channel from favorite Clear favorite channel list Status of favorite channel only Enable/disable favorite channel only Status of auto sort favorite channel Enable/disable auto sort favorite Sort favorite channel immediately Status of video extension Enable/disable video extension Status of video routing Set video routing follow or specified Status of video input / output mode Set input / output, 0=DVI, 1=VGA, 2=DVI+VGA Status of video output resolution Set output resolution, 5=customize Status of customize resolution Set customize resolution Status of video quality Set video quality Status of video dither Set video dither Update EDID from TX or monitor of RX Resume stream Pause stream Stop stream and send black screen Status of video wall function Enable/disable video wall Status of video wall mode Set video wall mode/single mode Load video wall setting (all) Load video wall layout (MAX Row/MAX Column/Row/Column) Save video wall setting (all) Show outer width of monitor Set outer width of monitor Show outer height of monitor Set outer height of monitor Show width of viewable area Set width of viewable area Show height of viewable area Set height of viewable area Show maximum row of video wall Set the row 1~8 of video wall Show maximum column of video wall Set the column 1~16 of video wall Show position in row Set position in row Show position in column Transmitter not support parameter FAVORITE Transmitter not support parameter ROUTING, SCALER, CUSTOMIZE, RESUME, PAUSE, and BLACK Receiver not support parameter QUALITY and DITHER Transmitter support FUNC only AUDIO USB RS232 IR COLUMN [ 0~15 ] STRETCH ? STRETCH [ 0~2 ] ROTATE ? ROTATE [ 0~7 ] SHIFT_V SHIFT_V [ 0~399 | 400 | 401~801 ] SHIFT_H ? SHIFT_H [ 0~399 | 400 | 401~801 ] SCALE_V ? SCALE_V [ 0~255 ] SCALE_H ? SCALE_H [ 0~255 ] ENABLE %1_%2_%3_%4 MONITOR_INFO %1_%2_%3_%4 FUNC ? FUNC [ ENABLE | DISABLE ] ROUTING ? ROUTING [ FOLLOW | 0~999 ] SELECT ? SELECT [ 0~2 ] IN ? IN [ 0 | 1~100 ] OUT ? OUT [ 0 | 1~100 ] FUNC ? FUNC [ ENABLE | DISABLE ] ROUTING ? ROUTING [ FOLLOW | 0~999 ] REQUEST KM FUNC ? KM FUNC [ ENABLE | DISABLE ] FUNC ? FUNC [ ENABLE | DISABLE ] ROUTING ? ROUTING [ FOLLOW | 0~999 ] SELECT ? SELECT [0~4 ] CTRL ? CTRL [0~2 ] BAUD ? BAUD [ 0~9 ] NEWLINE ? NEWLINE [ 0~3 ] TRIGGER ? TRIGGER [ 0~3 ] FUNC ? FUNC [ ENABLE | DISABLE ] ROUTING ? ROUTING [ FOLLOW | 0~999 ] CTRL ? CTRL [ ENABLE | DISABLE ] ID ? ID [ 0~10 ] KEY [ 0~32 ] ? User Manual HKM02BP-4K Set position in column Status of stretch type Set stretch, 0 = Auto, 1 = Stretch Out, 2 = Fit In Status of rotate type Set rotate, 0 = default Status of vertical shift 0~399: up, 400:default, 401~801: down Status of horizontal shift 0~399: up, 400:default, 401~801: down Status of vertical scale Set vertical scale Status of horizontal scale Set horizontal scale %1 = MAX_ROW, %2 = MAX_COLUMN, %3 = ROW, %4 = COLUMN %1 = VW, %2 = OW, %3 = VH, %4 = OH Status of audio extension Enable/disable audio extension Status of audio routing Set audio routing follow or specified Status of audio setting Select audio of TX input or RX output (0=Digital, 1=Analog, 2=Auto) Status of audio input volume Set audio input volume (%), 0 = Mute Status of audio output volume Set audio output volume (%), 0 = Mute Status of USB extension Enable/disable USB extension Status of USB routing Set USB routing follow or specified Request USB access (multicast only) Status of keyboard mouse extension Enable/disable keyboard mouse extension Status of RS232 extension Enable/disable RS232 extension Status of RS232 routing Set RS232 routing follow or specified Status of RS232 setting 0=Disable, 1=Extender, 2=Keypad, 3=Auxiliary, 4=Console Status of RS232 control setting 0=disable, 1=enable, 2=insensitive Status of baud rate 0=115200, 1=57600, 2=38400... 9=300 Status of newline format 0=Linux, 1=Windows, 2=Mac, 3=Other Status of trigger 0=Linux, 1=Windows, 2=Mac, 3=Other Status of IR extension Enable/disable IR extension Status of IR routing Set IR routing follow or specified Status of IR control setting Enable/disable IR control Status of IR remote ID Set IR remote ID Status of IR key setting Transmitter not support parameter ROUTING Transmitter not support parameter ROUTING and REQUEST Transmitter not support parameter ROUTING Transmitter not support parameter ROUTING 14 BUTTON ROTARY_SW HDCP EDID KEY [ 0~32 ] = address, command KEY IMPORT BLOCK ? BLOCK [ ENABLE | DISABLE ] CTRL ? CTRL [ ENABLE | DISABLE ] LOCK ? LOCK [ ENABLE | DISABLE ] ? [ ENABLE | DISABLE ] ? 0~2 UPDATE SELECT ? SELECT [ 0~3 ] HDMI SCREEN OSD ROUTING DEVICE GROUP PARTY NET QUERY 15 MODE ? MODE [ 0~1 ] CTRL ? CTRL [ ENABLE | DISABLE ] ? [ ON | OFF ] SAVER ? SAVER [ ENABLE | DISABLE ] OPTION ? OPTION [ 0~2 ] ON "string" OFF OFF ? OFF [ 0~65535 ] ? [ ENABLE | DISABLE ] LOAD [ 0~3 ] SAVE [ 0~3 ] ? [ 0~999 ] ? [ 0~99 ] ? [ 0~99 ] RECONNECT DISCONNECT STOP MULTICAST ? MULTICAST [ ENABLE | DISABLE ] JUMBO_FRAME ? JUMBO_FRAME [ ENABLE | DISABLE ] IP_MODE ? IP_MODE [ 0~2 ] IP ? IP [ xxx.xxx.xxx.xxx ] NETMASK ? NETMASK [ xxx.xxx.xxx.xxx ] GATEWAY ? GATEWAY [ xxx.xxx.xxx.xxx ] IP MAC User Manual HKM02BP-4K Set mapping of third party IR remote Import IR key setting Status of IR quick block Enable/disable IR quick block Status of button control Enable/disable button control Status of button lock Enable/disable button lock Status of rotary switch Enable/disable rotary switch Status of HDCP Always On 0=Disable, 1=HDCP 1.4, 2=HDCP 2.2 Update EDID from monitor of RX Status of TX default EDID setting 0=HDMI, 1=DVI, 2=VGA, 3=Loop Out Status of EDID process 0=normal, 1= Patch EDID Status of HDMI 5V control Enable/disable HDMI 5V control Status of screen settings Screen on/off Status of screen saver Enable/disable screen saver Status of behavior after screen off Set behavior after screen off HKM02BT only Transmitter not support parameter UPDATE, only HKM02BT support loop out Receiver not support parameter SELECT and Mode Transmitter not support parameter CTRL Transmitter not support this command Show "string" on screen (30 seconds) Turn off OSD immediately Transmitter not support this Status of OSD duration (ms) command Set duration of OSD (ms) Status of free routing Enable/disable free routing Transmitter not support Load free routing setting parameter LOAD and SAVE Save free routing setting Status of device number Transmitter not support this Set device number command Status of group number Transmitter not support this Set group number command Status of party number Transmitter not support this Set party number command Reconnect with TX/RX Disconnection (keep routing channel) Stop all connection (Include routing channel) Status of multicast Disable=unicast Status of Jumbo Frame Enable/disable Jumbo Frame Status of IP mode 0=Auto, 1=static, 2=DHCP Transmitter not support parameter DISCONNECT Status of static IP address Set static IP address Status of subnet mask (static IP mode) Set subnet mask (static IP mode) Status of gateway (static IP mode) Set gateway (static IP mode) Status of current IP address Status of MAC address User Manual HKM02BP-4K AUXILIARY LOAD RESOLUTION VERSION BAUD ? BAUD [ 0~9 ] NEWLINE ? NEWLINE [ 0~3 ] TRIGGER ? TRIGGER [ 0~3 ] VERSION DEFAULT [ 0~3 ] PRESET 0~15 SAVE REBOOT CONSOLE SYSTEM APPLICATION [ 0~3 ] string [ 0~255 ] ? [ 0~255 ] [ 0~255 ] ? [ 0~255 ] Status of video resolution Status of firmware version Status of auxiliary baudrate 0=115200, 1=57600, 2=38400... 9=300 Status of auxiliary newline 0=Linux, 1=Windows, 2=Mac, 3=Other Status auxiliary trigger 0=Linux, 1=Windows, 2=Mac, 3=Other Status of auxiliary versions Load default to current setting Load system setting from bank 0~4 Load preset 0~15 to set RX group ID Save current system setting Save system setting to bank 0~4 Reboot Run console API command Status of system function Set system function Status of application function Set application function When load default the settings will be auto saved. PRESET for OEM version RX only For debug using, if input incorrect value will cause unpredictable problem, adjust by professional installer only. RS232 command not support backspace, delete or up, down, left, right to modification. If you enter command or parameters with wrong typing, please enter newline and re-enter full command and parameters again. Parameters with green means need to reboot to take effect. The maximum of OSD_ON is 30 characters per line, maximum 127 charcters, not support comma sign,, colon: and double quotation marks", some characters must use \x## format to display, ## means the characters number in ASCII HEX code e.g.: \x0a is line feed, \x28 is ( brackets sign, \x22 is " sign Example: >CMD_M861234> CHANNEL 12 (Set receiver which last 6 digits MAC Address is 861234 to Channel 12) (HEX code: 3E 43 4D 44 5F 4D 38 36 31 32 33 34 3E 20 43 48 41 4E 4E 45 4C 20 31 32 0D 0A) <ACK_M861234< OK (Receiver which last 6 digits MAC Address is F01234 response "OK") (HEX code: 3C 41 43 4B 5F 4D 38 36 31 32 33 34 3C 20 4F 4B 0D 0A) ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- >CMD_I0A12> CHANNEL 3 (Set receiver which IP Address is 169.254.10.18 to Channel 3 (HEX code: 3E 43 4D 44 5F 49 30 41 31 32 3E 20 43 48 41 4E 4E 45 4C 20 33 0D 0A) <ACK_I0A12< OK (Receiver which IP Address is 169.254.10.18 response "OK") (HEX code: 3C 41 43 4B 5F 49 30 41 31 32 3C 20 4F 4B 0D 0A) ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- >CMD_G34> CHANNEL 5 (Set receivers which Group No is 34 to Channel 5) (HEX code: 3E 43 4D 44 5F 47 33 34 3E 20 43 48 41 4E 4E 45 4C 20 35 0D 0A) (No response from multiple receivers) ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- >CMD_ALL> OSD ON "Hello! \x28123\x29 \x22ABC\x22" (ShowHello! (123) "ABC"to all monitor and send response) (HEX code: 3E 43 4D 44 5F 41 4C 4C 3E 20 4F 53 44 20 4F 4E 20 22 48 65 6C 6C 6F 21 20 5C 78 32 38 31 32 33 5C 78 32 39 20 5C 78 32 32 41 42 43 5C 78 32 32 22 0D 0A) (No response from multiple receivers) >CMD_ALL> OSD OFF 10000 (All receiver turn off OSD after 10 seconds) (HEX code: 3E 43 4D 44 5F 41 4C 4C 3E 20 4F 53 44 20 4F 46 46 20 31 30 30 30 30 0D 0A) 16 Keypad Control User Manual HKM02BP-4K You can use RS232 Keypad or terminal program with number key to emulate IR remote operation. Before using RS232 keypad you have to select Keypad by Menu 50 RS232 Select, and set keypad baudrate by Menu 54 Auxiliary Baudrate. Key 0~9 + . or # Enter * or Esc or Clear / Press Clear four times then press Enter Description Enter number Increase value Reduce value Previous value Confirm Cancel Call MENU Call MENU USB Hot Key Function In multicast mode support multi USB keyboard and mouse in each receivers, just plug and play, but only one USB FLASH drive / hard disk could be used at the same time. You have to click "Pause/Break" key three times of the keyboard on the receiver or IR remote MENU function 14 to establish USB FLASH drive /hard disk connection. APP Control Function APP name: B&W Video Wall Control II Android/iOS App Windows 10 Software download link: https://www.microsoft.com/store/apps/9P268VD25977 17 App instruction User Manual HKM02BP-4K IP Setting You could input the IP address of transmitter / receiver at link column of browser which printed in the label. If the label is missing or not able to identify you can check the IP address as below: How to get the IP address of receiver: 1. Check the sticker at bottom of receiver with default IP 2. Connect monitor with receiver, Local IP shows on right bottom. 3. MENU 1 by IR remote/panel button to shows IP Address on screen How to get the IP address of transmitter: 1. Check the sticker at bottom of transmitter with default IP address. 2. Connect monitor with receiver, Remote IP shows on right bottom. 3. MENU 6 by IR remote/panel button to shows IP Address on screen If the IP address on the label of transmitters/receivers is incorrect (maybe changed by someone), you could reset the transmitters and receiver to default in two ways below: 1. Press the channel button "-" than power on (power and link LED will be flash) to reset to default. 2. Press IR remote control MENU, 3, 3, 3, ENTER to reset to default. 18 Web configuration System Version Information Firmware version and other information User Manual HKM02BP-4K Update Firmware Click "Select File" to browse firmware at local disk drive then click "Upload" to start update. During update the web will shows the status as above message. Updated unit will reboot automatically after updating firmware. If not, please reboot manually. Do not refresh, close, switch tab of web browser or power off to avoid any damage during firmware update. 19 User Manual HKM02BP-4K Utilities Factory Default Reboot Default EDID Console API Command Set system to factory default Reboot system Set EDID to default 1080p 7.1 channel audio Enter Console API command to change setting or control 20 Statistics Indicate system status User Manual HKM02BP-4K 21 Video Wall: User Manual HKM02BP-4K Basic Setup Bezel and Gap Compensation: Set outer width/height of monitor and width/height of viewable area. OW: outside width OH: outside height VW: viewable width VH: viewable height Please note: 1. The viewable width/height must be less than the outside width/height. 2. Keep all values be 0 if you do not use this function. 3. The value is based on millimeter and MUST be integer. Wall Size and Position Layout: Set scale of video wall and position of monitor Vertical monitor count: 1~8 Horizontal monitor count: 1~16 Row position: 0~7 Column position: 0~15 Preferences: Set extension way and rotation Select the video fit in the screen or stretch out and rotate angle Apply To: 1. All: Configure all Transmitter and Receiver in the list. 2. This (Local): Current device which you log in by web browser. 3. Hosts or Clients: select which Transmitter or Receiver you want to configure. Show OSD: Check this box to show receiver's specific number (follow list order) to connected monitor 22 Advance Setup: User Manual HKM02BP-4K 23 Before enter "Advanced Setup", please complete the "Basic Setup" as follows: 1. In "Basic Setup", select Vertical and Horizontal Monitor Count. User Manual HKM02BP-4K 2. In "Advanced Setup", choose the target of the video wall to control Step 2: Control Options Reset to Basic Setup: Press "Reset" if user make incorrect operations. Stretch Type: Setup the video output to "Fit In' or "Stretch Out" mode in the screen 24 Clockwise Rotate: Setup the rotation angle 0,180, 270 degree of the video output Screen Layout (Row x Column): User Manual HKM02BP-4K Set up the number of vertical and horizontal monitor based on the video wall layout. Vertical number 1~8 and horizontal number 1~16. Row Position: Setup the row position of monitor, number from 0 to the total number of vertical monitor. Column Position: Setup the column position of monitor, number from 0 to the total number of horizontal monitor. 25 Horizontal/Vertical Shift: Horizontal/Vertical Scale Up User Manual HKM02BP-4K Horizontal Shift: Set the video horizontal shift, Left or Right by pixels. Vertical Shift: Set the video vertical shift, Up or Down by pixels. Horizontal Scale Up: Set the video horizontal scale up by pixels. Vertical Shift Scale Up: Set the video vertical shift scale up by pixels. Consol API Command: Input Linux command to do advanced setup. 26 Network: User Manual HKM02BP-4K IP Setup: IP Mode could be Auto IP, DHCP, Static three mode Host default setting is Static IP, client default setting is Auto IP For mass deploying please use static or DHCP mode. Notice: if there is no DHCP server in network the host/client will keep reboot, you need to set the host/client to factory default Press channel button "-" than power on (power and link LED will be flash) Casting Mode : Could be Multicast, Unicast mode, default is Multicast When using Multicast mode, please check the "Auto select USB operation mode per casting mode" box 27 Functions for Transmitter: User Manual HKM02BP-4K Video over IP Enable Video over IP: This function setup the video signals send from network. Enable Video Wall: This function setup the video wall, default is not checked. Maximum Bit Rate: Set maximum bit rate. Maximum Frame Rate: Set maximum frame rate. USB over IP Enable USB over IP: Enable/disable USB extender function. Operation Mode: Set USB operation mode. Recommand Auto select mode. Compatibility Mode: Set USB compatibility mode. 28 Serial over IP User Manual HKM02BP-4K Enable Serial over IP: setup Serial (RS232) signal sends from network Operation Mode:Default is "Type 2 (Recommended. Dumb redirection.)" Baudrate Setting for Type 2 : default is 115200, 8, None, 1 29 Functions for Receiver: User Manual HKM02BP-4K Video over IP Enable Video over IP: This function setup the video signals send from network. Copy EDID from this Video Output: Copy EDID from TV when booting (unicast mode only), default is not checked. Scaler Output Mode: Select the required scalar output mode or select "Customize" and input 8 Hex values for more video output resolution and refresh rate selections. 1) 80000004: HD 720p60 2) 81000061: WXGA 1366x768@60 3) 81000040: WXGA+ 1440x900@60 4) 81000051: WUXGA 1920x1200@60 5) 8100003C: SXGA+ 1400x1050@60 Timeout for Detecting Video Lose: Please do not change this. Turn off screen on video lost: Please do not check this box 30 User Manual HKM02BP-4K USB over IP: Enable USB over IP: Enable/disable USB extender function. Operation Mode: Set USB operation mode. Recommand Auto select mode. Compatibility Mode: Set USB compatibility mode. 31 User Manual HKM02BP-4K Troubleshooting 1. Transmitter/receiver boot time require 30 seconds and will be able to control after booting, First time reboot after reset to default will be longer than 30 seconds. 2. Not recommend to work with existing LAN connection to avoid large video, data transmission or multicast packets to slow down your other LAN devices. 3. Gigabit switching hub muse support IGMP and Jumbo Frame over 8K in order to achieve the best quality 4. If monitor shows green screen, please check if the switch running under gigabit and IGMP/Jumbo Frame function enabled. 5. If video not smooth please check if IGMP function enabled or bandwidth of switch closes to maximum. 6. If UTP and SFP connected together the first connected one will get the priority, the other one will online automatically once another one failed. 7. If Ethernet is not connected may cause unpredictable problem or OSD message error, please connect to the Ethernet and reboot. 8. Default EDID is 1080p 7.1 audio, you can use Menu function 44 to copy EDID from monitor of RX. 9. If the monitor of RX shows shortly then turns into black but OSD shows properly, please check the HDCP version of monitor support is tally with the source required, and the casting mode of TX/RX are the same and the HDCP setting is correct. 10. If receiver switches to transmitter which no video input, it will show blank screen or last still image for seconds. 11. Fast switch mode might cause screen or audio abnormal briefly when switch channel. 12. When output resolution is fixed, the screen or OSD might be cut a little if the source resolution is much different with the output (like 4K downscale to 720p). 13. In high resolution (like 1080p or 4K) the OSD response will be delayed a little bit. 14. In video wall mode, the OSD may not be in correct size and position 15. RS232 only support data transmission (TXD, RXD), not support hardware handshake (RTS, CTS, DTR, DSR...) 16. Power from power adapter with priority than power from PoE. 17. The front panel IR will be disable when external IR cable plugged. 18. If IR remote not work properly, please check the battery (especial in low temperature) and reset IR ID. 19. Audio in of RX only works at unicast mode, and the audio in and audio out of TX must be connected. 20. Audio in of RX is designed for mono Mic in, not for stereo Line in. 21. When using computer or mobile APP management the IP address should be set in same network segment. 22. TV wall setting parameter between APP/PC software and IR menu/Web are different and might be cover each other, we recommend set TV wall by one of two ways to prevent conflict. 23. PC software and APP operation please refer to software operating instruction. 24. Not recommend control by panel, computer software and APP at the same time to prevent conflict. 32 Package Include HKM02BT-4K Package Include: Transmitter x 1 pcs USB A to B cable x 1 pcs IR emitter cable x 1 pcs HKM02BR-4K Package Include: Receiver x 1 pcs IR emitter cable x 1 pcs IR remote control x1 pcs User Manual HKM02BP-4K 33 Specification User Manual HKM02BP-4K ITEM NO. Support Compliance Max. Video Resolution Max. Transmission Distance Audio Format IR Support Ports & Interfaces Video Input Video Output Video Loop-out Analog Audio Input Analog Audio Output USB Interface IR Interface RS232 Interface Link Interface Power PoE Support Power Consumption Ambient Temperature Operation Storage Humidity Physical Characteristics Dimensions Weight HKM02BPT-4K HKM02BPR-4K HDCP 2.2, USB 1.1, USB 2.0 4K@30Hz 4:4:4 150M over CAT5e Cable or Greater 7.1 LPCM 192kHz, Dolby True HD, DTS-HD Master Audio, ATMOS, DTS:X 20-60kHz , ±45°, 5M 1 x HDMI Type A 1 x RJ45 1 x HDMI Type A 1 x 3.5mm Stereo Phone Jack (Line In) 1 x 3.5mm Stereo Phone Jack (Line Out) 1 x USB Type B (USB 2.0) 1 x 3.5mm Stereo Phone Jack 1 x DB9 Female 1 x RJ45, 1 x SFP 1 x RJ45 HDMI Type A 1 x 3.5mm Mono Phone Jack (Mic In) 1 x 3.5mm Stereo Phone Jack (Line Out) 2 x USB Type A (USB 1.1) 2 x USB Type A (USB 2.0) 1 x 3.5mm Stereo Phone Jack 1 x DB9 Male 1 x RJ45, 1 x SFP 802.3af 8W 802.3af 7W 0 to 55 -20 to 85 Up to 95% 210 x 123 x 40mm 710g 167 x 103 x 40mm 530g 34Microsoft Word 2010 Microsoft Word 2010