FaceSec FBD01WS Biometric Recognition Device
Installation Guide and Specifications
Installation Instructions
Installation Method 1
- Secure the bracket to the 86 box with 2 screws (M4*40).
- Connect Cable A on the bracket to the corresponding interface of the device.
- Mount the device from top to bottom onto the bracket.
- Use 2 screws (M2*7) to lock the device and bracket from the bottom of the device.
Installation Method 2
- Select the appropriate mounting location and attach the positioning sticker.
- Align holes 5 and 6 on the positioning sticker to drill holes in the wall (recommended aperture 6mm, depth 40mm).
- Remove the positioning sticker.
- Secure the bracket to the wall with 2 sets of expansion screws (M4*25).
- Connect Cable A on the bracket to the corresponding interface of the device.
- Mount the device from top to bottom onto the bracket.
- Use 2 screws (M2*7) to lock the device and bracket from the bottom of the device.
Precautions
- For holes 1 to 4 on the bracket (refer to positioning sticker), do not remove the waterproof pad if the position is not in use.
- Holes 3 and 4 on the bracket (refer to positioning sticker) support the use of an 86-box repairer.
- If using an 86-box repairer, replace the screws that come with it with the screws provided in the accessory kit.
Port Description
- RS485_B
- RS485_A
- GND
- WG_DO_0
- WG_D1_0
- GND
- WG_DO_I
- WG_D1_I
- Alarm 1
- Alarm 2
- Alarm 3
- GND
- +12VDC+
- IN
- Relay_NC
- Relay_COM
- Relay_NO
- LAN
- Cable A
Dimensional Drawing
The device has dimensions of 95mm (width) x 159mm (height) x 25mm (depth). It includes mounting holes and connection points. A bracket is shown for mounting, with Cable A connecting to the device. Screws like M2*7 are used for securing.
Recognizable Position
This section describes optimal placement for facial recognition. It includes a diagram showing a person standing at a distance from a wall where the device is mounted. The diagram illustrates:
- Person to wall distance (W): ranges from 80-100 cm.
- Camera to ground distance (H): ranges from 130-150 cm.
- Recognizable height (L): ranges from 140-150 cm.
Specifications
| Feature | Details |
|---|---|
| Liveness Detection | Support |
| Verification Method | 1:1, 1:N, 1:1/1:N |
| Recognition Speed | Per Recognition time (under 1:N mode) ≤0.3Sec |
| User Capacity | Up to 20000 users |
| Operating System | Android 8.1 |
| Camera | Dual wide-angle camera (RGB + NIR) |
| Display | 5.5-inch LCD touch display |
| Multi touch | Support |
| Tamper alarm | Support |
| Relative Humidity | 5% to 95% non-condensing |
| Dimensions | 95*159*25mm |
| Power Supply | DC 12V 2A |
| Operating temperature | -10° to 55° C |
| Communication Method | Wi-Fi, Ethernet |
| Physical interface | RS485*1, Wiegand TX*1, Wiegand RX*1, Dry contact*1, RJ45*1, Alarm interface*3 |
| Power button | Support |
| WIFI 2.4G | B/G/N |
| WIFI 5G | 5.8G band 1/2/3/4 |
EU Declaration
This product can be used across EU member states. FaceSec Japan Co., Ltd. declares that this device complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. The product does not include an AC/DC adapter. A DC 12V/2A adapter compliant with Directive 2014/30/EU must be purchased separately. The adapter should be installed near the equipment and be easily accessible.
Operation steps for viewing authentication information:
- Enter the "Setting" interface and click "About".
- Enter the "About" interface and click "Credentials".
FCC Warning
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.