Instruction Manual for CHIEF models including: FSB-75100, Small Display Interface Kit, FSB-75100 Small Display Interface Kit
Chief FTR100 Tilt wall mount for small commercial displays at Crutchfield
File Info : application/pdf, 9 Pages, 766.04KB
DocumentDocumentINSTALLATION INSTRUCTIONS FSB-75100 Small Display Interface Kit Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative. WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer! TOOLS REQUIRED FOR INSTALLATION / PARTS A (4) [Mounting buttons] B (4) 3/4" x 1/4" C (4) 3/4" x 1/2" D (4) M4 x 20mm INSTALLATION INSTRUCTIONS WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing mounting buttons. Flush Mount Display Interface Installation 1. Place display face down on a clean dry surface. 2. Assemble mounting buttons (A) to display using four M4 x 20mm (D) Phillips pan head screws. (See Figure 1) E (4) M4 x 25mm F (4) M4 x 30mm 2. Place mounting buttons (A) over four spacers (B or C). (See Figure 2) 3. Assemble mounting buttons (A) to display using four M4 x 25mm (E) or four M4 x 30mm (F) Phillips pan head screws through spacers. (See Figure 2) (B or C) x 4 (A) (A) 3 (E or F) x 4 Figure 2 Chief® is a registered trademark of Milestone AV Technologies. All 2 (D) x 4 rights reserved. Figure 1 Recessed Mount Display Interface Installation 1. Align and place four spacers (B or C) over mounting holes in display back. (See Figure 2) Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. Chief, a products division of Milestone AV Technologies 6436 City West Parkway, Eden Prairie, MN 55344 8800-002666 Rev00 ©2014 Milestone AV Technologies · P: 800.582.6480 / 952.225.6000 · F:877.894.6918 / 952.894.6918 12/14 INSTALLATION INSTRUCTIONS Small Flat Panel Tilt Wall Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description FTR1U / FTR100 FTR1U / FTR100 DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. Chief® is a registered trademark of Milestone AV Technologies. All rights reserved. DEFINITIONS MOUNTING SYSTEM: A MOUNTING SYSTEM is the primary Chief product to which an accessory and/or component is attached. Installation Instructions WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the combined weight of all components attached to FTR1U/FTR100 mounting system does not exceed 45 lbs (20.4 kg). WARNING: Watch for pinch points! Do NOT place fingers in between moving parts! WARNING: Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer. WARNING: Never operate this mounting system if it is damaged. Return the mounting system to a service center for examination and repair. ACCESSORY: AN ACCESSORY is the secondary Chief product which is attached to a primary Chief product, and may have a component attached or setting on it. COMPONENT: A COMPONENT is an audiovisual item designed to be attached or resting on an accessory or mounting system such as a video camera, CPU, screen, display, projector, etc. WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. WARNING: Do not use this mounting system outdoors. IMPORTANT ! : The FTR1U/FTR100 mounts are designed to be mounted to a: · single 2" x 4" wood stud; OR a · single 2" x 4" wood stud on one side and drywall on the other side using the drywall anchors provided. NOTE: The FTR1U includes the Chief FSB1U interface bracket. NOTE: The FTR100 includes the Chief FSB75100 interface bracket. --SAVE THESE INSTRUCTIONS-- IMPORTANT SAFETY INSTRUCTIONS WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer's responsibility to make sure the mounting system is properly assembled and installed using the instructions provided. WARNING: Failure to provide adequate structural strength for this mounting system can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the structure to which this mounting system is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the mounting system. The wall to which the mounting system is being attached may have a maximum drywall thickness of 5/8" (1.6cm). Do not install drywall anchors into the seam between drywall pieces. 2 Installation Instructions DIMENSIONS 5.78 146.7 4 .00 1 0 1.6 2.5 0 63 .5 0 .3 8 9 .5 4 .0 0 1 0 1.6 0.9 9 25 .2 0.2 5 x6 6.4 3.94 100.0 1.97 50MM MO UNTING 1 .3 8 3 4 .9 1.8 8 47 .6 3.7 5 95 .3 2 .3 8 6 0 .3 1.90 48.2 0 .50 1 2.7 6.37 161.7 0.44 11.1 1.56 39.6 1.97 50.0 3.12 79.1 3.94 100MM MOUNTING 5.61 142.5 FAC E TILTS 5 UP 15 DOWN 4.75 120.7 FTR1U / FTR100 2 .0 7 5 2.5 DIMENSIONS: INCHES [MILLIMETERS] 3 FTR1U / FTR100 LEGEND Tighten Fastener Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis à pointe cruciforme TOOLS REQUIRED FOR INSTALLATION Installation Instructions Pencil Mark Marcar con lápiz Stiftmarkierung Marcar com lápis Segno a matita Potloodmerkteken Marquage au crayon Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Hammer Martillo Hammer Martelo Martello Hamer Marteau PARTS 1/8" (wood stud) 3/8" (drywall) A (1) [FTR1U/FTR100 Assembly] #2 B (2) #10 x 2-1/2" D (2) 10-24 [Hollow wall anchor] C (4) #10 Interface bracket (including hardware and installation instructions) 4 Installation Instructions FTR1U / FTR100 INSTALLATION The FTR1U/FTR100 may be installed either centered on a single wood stud, or anchored to a single wood stud on one side, and to drywall (1/2" minimum thickness) on the other side. The FTR1U/FTR100 allows a tilt range from +5° to -15°. Install Mount Centered to Single Wood Stud 1. Determine approximate mounting location, keeping in mind the display size. 2. Use a stud sensor to locate applicable wood stud. Mark location with a pencil. 3. Level FTR1U/FTR100 assembly (A) at desired height and, using it as a template, mark the location of upper and lower pilot holes. Ensure marks are in the center of wood stud. NOTE: Mount can provide ±1/2" of lateral shift by using mount holes on either side of vertical center line. WARNING: ELECTRICAL SHOCK HAZARD! Drilling into electrical wires or cables can cause DEATH or SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surfaces is free of electrical wires and cables before drilling or installing mount fasteners. 4. Drill pilot holes using a 1/8" drill bit. Ensure pilot holes are straight. 5. Fasten FTR1U/FTR100 assembly to wood stud using two #10 x 2-1/2" Phillips head screws (B) through two #10 washers (C), FTR1U/FTR100 assembly (A), and drywall (not shown) and install into pilot holes. (See Figure 1) Install Mount to a Single Wood Stud and Drywall WARNING: Drywall must have a minimum thickness of 1/2" and a maximum thickness of 5/8". Do not install drywall anchors into the seam between drywall pieces. 1. Determine approximate mounting location, keeping in mind the display size. 2. Level FTR1U/FTR100 assembly (A) at desired height and, using it as a template, mark the location of the four anchor holes (one in each corner slot). (See Figure 2) IMPORTANT ! : Two holes MUST be centered on a single wood stud. WARNING: ELECTRICAL SHOCK HAZARD! Drilling into electrical wires or cables can cause DEATH or SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surfaces is free of electrical wires and cables before drilling or installing mount fasteners. 3. Drill 1/8" pilot holes in wood stud locations. Ensure pilot holes are straight. (See Figure 2) 4. Drill 3/8" anchor holes in the other two marked locations. Ensure holes are straight and completely through drywall. (See Figure 2) 2 x 4 5 (B) x 2 2 x 2 4 x 2 3 x 2 1/8" 4 x 2 3/8" (C) (A) Figure 1 Figure 2 5 FTR1U / FTR100 5. Gently tap two anchors (D) into anchor holes. Anchor barbs should be fully engaged in drywall. (See Figure 3) and (See Figure 4) 9 Installation Instructions (B) x 2 (A) 5 (D) x 2 (D) x 2 Figure 3 6. Using Phillips screwdriver, tighten anchor screw until anchor has fully collapsed against back side of drywall. (See Figure 4) NOTE: Anchor screw will feel tight until anchor begins to collapse. Screw will then turn easier for many turns. Screw will feel tight when anchor has fully collapsed. 7. Remove and save anchor screws from anchors (D). NOTE: Anchors (D) may come with small washers which should be discarded. Anchor not collapsed Drywall Anchor collapsed 8 anchor screws x 2 (C) x 4 Figure 5 Install Display to Mount NOTE: Attach interface bracket to display following instructions included with interface bracket. 1. Open latching flag by rotating flag clockwise on FTR1U/ FTR100 assembly (A). (See Figure 6) 1 Latching flag open Latching flag closed Anchor barb Figure 4 8. Insert anchor screws through two #10 washers (C), FTR1U/ FTR100 assembly (A) and install into collapsed anchors (D). (See Figure 5) 9. Install two #10 x 2 1/2" Phillips tapping screws (B) through two #10 washers (C), FTR1U/FTR100 assembly (A) and into wood stud. (See Figure 5) 6 Figure 6 Installation Instructions 2. Lift and maneuver display such that all mounting buttons fit into openings on FTR1U/FTR100 assembly (A). (See Figure 7) 3. Lower display firmly into place. Ensure each mounting button has fully seated in the opening. (See Figure 7) 4. Close latching flag by rotating flag counterclockwise on FTR1U/FTR100 assembly (A). (See Figure 7) Latching flag (A) 4 2 FTR1U / FTR100 Add padlock here 3 Display Figure 7 NOTE: Example shows mounting display in the 100mm x 100mm pattern. FTR1U/FTR100 assembly (A) will also accommodate a 75mm x 75mm pattern. (See Figure 8) NOTE: Display not shown for clarity. NOTE: Display not shown for clarity. Figure 9 5. Connect cables to display as required. Adjusting Tilt 1. Loosen adjusting screws on each side of display (See Figure 10). 2. Adjust tilt as desired. 3. Tighten adjusting screws. 5° Tilt Up 15° Tilt Down Button location for 100mm x 100mm pattern (4 places) Button location for 75mm x 75mm pattern (4 places) Figure 8 NOTE: An optional padlock may be used to secure latching flag in place. (See Figure 9) 123 Figure 10 7 FTR1U / FTR100 Installation Instructions Chief, a products division of Milestone AV Technologies 8800-002877 Rev02 ¤2017 Milestone AV Technologies www.milestone.com 08/17 USA/International Europe Asia Pacific A 6436 City West Parkway, Eden Prairie, MN 55344 P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918 A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 F +31 (0) 495 580 845 A Office No. 918 on 9/F, Shatin Galleria 18-24 Shan Mei Street Fotan, Shatin, Hong Kong P 852 2145 4099 F 852 2145 4477