Weiser GED240 Keypad Deadbolt

Step 1: Prepare the Door and Check Dimensions

A. Door Hole Diameter: Ensure the door hole is either 54 mm (2-1/8 in) or 38 mm (1-1/2 in).

B. Backset: Verify the backset is either 60 mm or 70 mm (2-3/8 or 2-3/4 in).

Additional door preparation may be required for doors with 38 mm (1-1/2 in) holes.

C. Door Edge: Check that the door edge is 25 mm (1 in) thick.

D. Door Thickness: Measure to confirm the door is between 35 mm and 44 mm (1-3/8 and 1-3/4 in) thick.

Please contact customer service if door thickness exceeds 44mm (1-3/4 in) for a thick door kit.

Step 2: Install the Latch and Strike

A. Latch Orientation: Hold the latch in front of the door hole. Ensure the rectangular shaped hole is centered in the door hole. If not, rotate the latch face 180 degrees to extend the latch.

B. Chiseled Door Edge:

• If the door edge is chiseled: Install the latch in the door with the supplied screws. Ensure the slotted hole is at the bottom of the latch.
• If the door edge is not chiseled: Use a flathead screwdriver to remove the latch face. Grip the latch with one hand and twist the collar off with the other. Install the drive-in collar. Align tabs with holes in the collar and ensure it snaps into place. Pull the collar to test for a tight fit. Install the latch in the door using a wood block and hammer.

IMPORTANT: Make sure the latch bolt is fully retracted (in the unlocked position) ?.

C. Install Strike: Install the strike on the door frame. Make sure the hole in the door frame is drilled a minimum of 25 mm (1 in) deep.

Step 3: Install the Exterior Keypad

A. Door Hole Diameter Check:

• If the diameter is 54 mm (2-1/8 in), an adapter ring is not needed.
• If the diameter is 38 mm (1-1/2 in), an adapter ring is required for installation.

B. Prepare Screws: Locate screws for step 3C and keep them within reach.

C. Install Exterior Keypad and Mounting Plate:

1. Rotate the flat blade to a horizontal position to match the latch orientation.
2. Support the exterior assembly during mounting plate installation. Ensure the bolt is RETRACTED.
3. Route the cable underneath the latch. The TOP of the mounting plate should be visible and kept parallel to the edge of the door.
4. Insert the cable through the center hole, then push the cable into the bottom hole.
5. Tighten the screws evenly. DO NOT overtighten.
6. Ensure the flat blade is centered in the mounting plate hole.

Test Latch: Insert the key and test the latch. If the latch does not extend or retract smoothly, adjust the screws. Remove the key when sure the latch bolt is FULLY EXTENDED ?.

Step 4: Install the Interior Assembly

A. Prepare Interior Assembly: Remove the interior cover from the interior assembly. Check that the latch bolt is in the extended/locked position ?. Ensure the turnpiece shaft is rotated as shown.

B. Secure Interior Assembly:

1. Route the cable around the side notch and bottom of the interior assembly.
2. Remove the interior cover from the interior assembly.
3. Connect the cable. Ensure a tight cable connection.
4. Insert the flat blade into the turnpiece shaft. If the turnpiece is not pointing up, rotate the turnpiece until you hear a click.
5. Ensure you are using the correct screws. Using incorrect screws will damage the product.

Do not install batteries until step 5.

Step 5: Install the Batteries

A. Install Batteries: Install 4 AA batteries ? in the interior assembly. Ensure your door is open while installing batteries and the interior cover is off. For best results, use new, non-rechargeable alkaline batteries only. Ensure correct polarity.

B. Install Interior Cover: Install the interior cover for the interior assembly.

Step 6: Add User Codes (12 max)

During User Code programming, a timeout will occur if the keypad is not pressed for 5 seconds, requiring you to restart the procedure. For security reasons, the first 4 digits of each User Code must be unique.

1. Make sure the interior cover is off. Press the Program button once.
2. Press number 1.
3. Press the Program button once.
4. Enter user code (4 to 8 digits). A total of 12 user codes may be programmed.
5. Press the Program button again.

After the first User Code is created, the latch bolt will automatically retract and extend to learn the locking and unlocking direction of the door. The lock button will indicate success (GREEN) or failure (RED).

Step 7: Test the Lock

Before you can lock and unlock the door, a User Code must be created (refer to Step 6). Confirm that the code(s) added can unlock the door.

A. To Lock: Press the lock button ?. The lock will beep twice and the lock button will flash amber as the deadbolt extends.

B. To Unlock: Enter the user code. The lock will beep twice and the lock button will flash green as the deadbolt retracts ?.

Step 8: Adding a One-time User Code

1. Remove interior cover. Press programming button.
2. Press number 1.
3. Press number 2.
4. Enter the one-time user code (4 to 8 digits).
5. Press the programming button again.

Up to 2 One-time User Codes can be saved. They are deleted automatically after use. The same One-Time User Code can be created again after it's used.

Step 9: Delete a Single User Code

1. Remove interior cover.
2. Press number 1.
3. Press the programming button.
4. Enter the user code you want to delete.
5. Press the programming button again.

Test the code while the door is open to ensure it no longer unlocks the door.

Step 10: Delete ALL User Codes

Keypad locking function will be disabled when User Codes are deleted. The lock can only be operated manually by a key ? during this time.

1. Remove interior cover. Press programming button.
2. Press number 2.
3. Press the programming button.
4. Press number 4.
5. Press the programming button again.
6. Enter the user code to be deleted.
7. Press the programming button again.
8. Enter the user code to be deleted again.
9. Press the programming button again.

If unsuccessful: Make sure you entered the same user code in steps 4 and 6 (referring to the deletion sequence, likely meaning the code entered in step 6 and step 8). Test code while the door is open. Test the User Code to make sure it no longer unlocks the door.

Step 11: Enable/Disable Audio

1. Remove interior cover. Press programming button.
2. Press number 2.
3. Press number 1.
4. Press the programming button.

LED status indicator will still function once audio is disabled. Repeat the programming steps to enable the audio.

Step 12: Enable/Disable User Codes

1. Remove interior cover. Press programming button.
2. Press number 2.
3. Press number 2.
4. Press the programming button.

When all User Codes are disabled, all electronic functions will be disabled as well. The door must be locked or unlocked manually with the key ?. Repeat the programming steps to enable the User Codes.

Step 13: Enable/Disable Auto-Lock

1. Remove interior cover. Press programming button.
2. Press number 3.
3. Press number 1.
4. Press the programming button.

Repeat the programming steps to disable the auto-lock.

Step 14: Change Auto-Lock Time Delay

1. Remove interior cover. Press programming button.
2. Press number 3.
3. Press number 2.
4. Press the programming button.
5. Choose and press button for delay: 30 seconds, 1 minute, 3 minutes, 5 minutes, 10 minutes.

Step 15: Door Rehanding

This feature is used for the lock to learn the orientation of your door (left- or right-handed). If a stuck/jammed bolt error continues to occur after performing this step, please make sure there is no obstruction from the strike or door jamb to prevent the bolt from extending.

1. Remove interior cover. Press programming button.
2. Press number 4.
3. Press the programming button.
4. Press the programming button again.

The latch bolt will extend and retract to learn the orientation of the door.

Step 16: Factory Reset

Lock must be in an unlocked position to factory reset. A factory reset will delete all User Codes and change all programming to factory settings. At this time, the lock can only be locked or unlocked manually with the key ?.

1. Remove interior cover. PRESS and HOLD programming button for 15 seconds.
2. The lock will emit a long beep.
3. Press programming button once more.

The latch bolt will extend and retract to learn the locking and unlocking direction of the door.

Step 17: Add/Change Programming Code

Enable/Disable Programming Code: Optional: A Programming Code enables programming changes without needing access to the Programming Button. This is ideal for landlords to program the lock without access to the interior programming button. Note: Once Programming Code is enabled, the Programming Button is disabled and can only be used to factory reset the lock. One Programming Code (4 to 8 digits) can be saved and cannot be the same as any User Code or used as a User Code to unlock the lock.

To program the lock with Programming Code: Follow the programming steps WITHOUT PRESSING the PROGRAMMING BUTTON.

To disable Programming Code: Enter Programming Code, press programming button, enter Programming Code again, press programming button again.

1. Remove interior cover. Press programming button.
2. Press number 5.
3. Press the programming button.
4. Enter Programming Code (4 to 8 digits).
5. Press the programming button again.