Matrix Aura Series G3-MS24FS

Product Information

WARNING: DEATH OR SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW THESE PRECAUTIONS TO AVOID INJURY!

Additional Warnings:

Important Safety Information

It is the sole responsibility of the purchaser of MATRIX products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment. It is recommended that all users of MATRIX exercise equipment be informed of the following information prior to its use.

Do not use any equipment in any way other than designed or intended by the manufacturer. It is imperative that MATRIX equipment be used properly to avoid injury.

Installation

  1. STABLE AND LEVEL SURFACE: MATRIX exercise equipment must be installed on a stable base and properly leveled.
  2. SECURING THE EQUIPMENT: Manufacturer REQUIRES that this stationary MATRIX equipment be secured to the floor to stabilize equipment and eliminate rocking or tipping over. This must be performed by a licensed contractor.
  3. Under no circumstances should you slide equipment across the floor due to risk of tipping. Use proper materials handling techniques and equipment recommended by OSHA. All anchor points must be able to withstand 750 lbs. (3.3 kN) pull-out force.

Maintenance

  1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by your country's local MATRIX dealer.
  2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain important information. If unreadable or missing, contact your MATRIX dealer for a replacement.
  3. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals.
  4. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so. MATRIX dealers will provide service and maintenance training at their corporate facility upon request.

Additional Notes

This equipment should only be used in supervised areas where access and control is specifically regulated by the owner. It is up to the owner to determine who is allowed access to this training equipment. The owner should consider a user's: degree of reliability, age, experience, etc.

This training equipment meets industry standards for stability when used for its intended purpose in accordance with the instructions provided by the manufacturer.

This equipment is for indoor use only. This training equipment is a Class S product (designed for use in a commercial environment such as a fitness facility). This training equipment is in compliance with EN 957-1 and the relevant portions of EN 957-2 and EN 957-4.

Unpacking

Thank you for purchasing a MATRIX Fitness product. It is inspected before it is packaged. It is shipped in multiple pieces to facilitate the compact packaging of the machine. Prior to assembly, confirm all the components by matching them with the exploded diagrams. Carefully unpack the unit from this box and dispose of the packing materials in accordance with your local laws. Exercise device must be assembled by a trained assembly team or be pre-assembled prior to delivery.

CAUTION: To avoid injury to yourself and prevent damage to the frame components, be sure to have proper assistance removing the frame pieces from this box. Please be sure to install the equipment on a stable base, and properly level the machine. Ensure a minimum clearance width of 0.6 meters (24") for access to and passage around MATRIX strength equipment. Please note, 0.91 meters (36") is the ADA recommended clearance width for individuals in wheelchairs.

Warranty

For North America, please visit matrixfitness.com for warranty information along with warranty exclusions and limitations.

Proper Usage

  1. Do not exceed weight limits of the exercise device.
  2. If applicable, set safety stops to appropriate height.
  3. If applicable, adjust seat pads, leg pads, foot pads, range of motion adjustment, or any other type of adjustment mechanisms to a comfortable start position. Make certain that the adjusting mechanism is fully engaged to prevent unintentional movement and to avoid injury.
  4. Sit on bench (if applicable) and get into appropriate position for exercise.
  5. Exercise using no more weight than you can safely lift and control.
  6. In a controlled manner, perform exercise.
  7. Return weight to its fully-supported start position.

Maintenance Checklist

ACTION FREQUENCY
Clean Upholstery 1 Daily
Inspect Cables 2 Daily
Clean Guide Rods Monthly
Inspect Hardware Monthly
Inspect Frame Bi-Annually
Clean Machine As Needed
Clean Grips 1 As Needed
Lubricate Guide Rods 3 As Needed

1 Upholstery & Grips should be cleaned with a mild soap and water or a non-ammonia based cleaner.

2 Cables should be inspected for cracks or frays and immediately replaced if present. If excessive slack exists cable should be tightened without lifting the head plate.

3 Guide rods should be lubricated with Teflon based lubricant. Apply the lubricant to a cotton cloth and then apply up and down the guide rods.

Product Specifications

20 kg / 64 lbs
Shipping Weight (2 cartons) 29 kg / 64 lbs
Product Weight
Legs 9.5 kg / 21 lbs
Shroud 12 kg / 26.5 lbs
Dimensions (L x W x H)
Individual side legs 42.5 x 9 x 19.5 cm / 16.75 x 3.5 x 17.75"
Rear leg 34 x 20 x 23 cm / 13.5 x 8 x 9"
Rear shroud 63.5 x 15.5 x 186 cm / 25 x 6.1 x 73.25"

Torque Values

135 Nm /100 ft-lbs
M12 Bolt (Nyloc Nut & Flowdrill) 135 Nm /100 ft-lbs
M10 Bolt (Nyloc Nut & Flowdrill) 77 Nm/57 ft-lbs
M8 Bolts 25 Nm / 18 ft-lbs
M8 Plastic 15 Nm /11 ft-lbs
M6 Bolts 15 Nm/11 ft-lbs
Pad Bolts 10 Nm/7 ft-lbs

Assembly

Hardware

Qty
Z01 Nylon Nut (M10) 4
Z02 Flat Washer (M10) 8
Z04 Bolt (M10x30L) 4
Z05 Bolt (M8x15L) 1
Z06 Flat Washer (M8) 1
Z07 Screw (M6x12L) 2

Hardware

Qty
Z01 Nylon Nut (M10) 4
Z03 Bolt (M10x105L) 4
Z07 Screw (M6x12L) 4
Z08 Arc Washer (M10) 8

Torque Value

Z03 35 Nm / 26 ft-lb

Sold Separately

Qty
Anchor Bolt (1/4" x 3") Item #THD25300H 13

Anchor points (x13)

Assembly Complete

The Matrix Aura Series G3-MS24FS is now assembled. Ensure all bolts are tightened to the specified torque values and that the equipment is stable and level.

Models: G3-MS24FS, G3-MS24FS Aura 8-Stack Multi Station, G3-MS24FS, Aura 8-Stack Multi Station, 8-Stack Multi Station, Multi Station

PDF preview unavailable. Download the PDF instead.

optimized---media 1358796 98456 Adobe PDF Library 17.0 Adobe InDesign 20.0 (Macintosh)

Related Documents

Preview MATRIX G3-S76 ROTARY HIP: Assembly, Safety, and Maintenance Guide
Comprehensive guide for the MATRIX G3-S76 ROTARY HIP, including unpacking, assembly instructions, safety precautions, maintenance checklist, product specifications, and warranty information.
Preview MATRIX AURA SERIES (G3-PL62) Smith Machine Owner's Guide
Comprehensive guide for the MATRIX AURA SERIES (G3-PL62) Smith Machine, covering important safety information, installation, maintenance, proper usage, product specifications, warranty, and assembly instructions.
Preview MATRIX G3-S71 Aura Series Leg Extension Machine - Owner's Manual & Assembly Guide
Comprehensive guide for the MATRIX G3-S71 Aura Series Leg Extension machine, covering proper usage, safety instructions, maintenance, product specifications, torque values, and detailed assembly steps. Includes information for commercial fitness facilities.
Preview MATRIX Aura Series G3-S30 Lat Pulldown: User Manual and Safety Guide
Comprehensive user manual and safety guide for the MATRIX Aura Series G3-S30 Lat Pulldown. Includes installation, proper usage, maintenance, product specifications, and warranty information.
Preview Matrix Strength 2021 Brochure: Commercial Fitness Equipment Solutions
Explore the Matrix Strength 2021 Brochure, detailing the Ultra, Versa, Aura, Go, Magnum, Varsity, and G1 series of commercial fitness equipment. Learn about Matrix Fitness's commitment to facility planning, smart design, and comprehensive support services.
Preview マトリックス ストレングス 2023年 ブローシャ:フィットネス機器概要
マトリックスの2023年ストレングス機器ブローシャ。ウルトラ、ヴァーサ、オーラ、ゴー、G1シリーズなどの革新的なデザイン、スマートテクノロジー、堅牢なパフォーマンスを備えたフィットネス機器を紹介します。
Preview MATRIX GO-S42 Seated Triceps Press - User Manual and Assembly Guide
Comprehensive user manual and assembly guide for the MATRIX GO-S42 Seated Triceps Press, part of the GO SERIES. Includes safety information, installation, usage, maintenance, and product specifications for commercial fitness facilities.
Preview Matrix Aura Abdominal G3-S50 Fitness Machine Specifications and Features
Detailed specifications and features for the Matrix Aura Abdominal G3-S50 fitness machine, including ease of use, frame details, and technical specifications.