Tyger Auto: Contact Us
Instruction Manual for TYGER models including: TG-LX3C82318 LanderX Running Board, TG-LX3C82318, LanderX Running Board, Running Board
Tyger Auto LanderX Running Board Compatible with 2019-2024 Chevy Silverado GMC Sierra 1500; 2020-2024 2500 3500HD | Crew Cab | TG-LX3C82318 | Drop Step Side Step Rail Nerf Bars : Automotive
File Info : application/pdf, 3 Pages, 2.04MB
DocumentDocumentTYGER LanderX TG-LX3C82318 BEFORE INSTALLATION READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT TORQUE VALUES Fastener Size Class 8.8 Torque (ft-lbs) 6mm 6-7 8mm 15-16 10mm 31-32 12mm 54-55 14mm 87-88 Class 10.9 Torque (ft-lbs) 6-7 22-23 44-45 78-79 125-126 x1 Driver/Left TYGER LanderX x1 Passenger/Right TYGER LanderX x4 Driver/Left Mounting Brackets x4 Passenger/Right Mounting Brackets x16 8mm x 30mm Hex Bolts x16 8mm x 25mm Combo Bolts x16 8mm Lock Washers x16 8mm x 24mm OD x 2mm Flat Washers (4) Passenger/Right Mounting Brackets (4) Driver/Left Mounting Brackets Passenger/Right TYGER LanderX Front 1/3 Customer Support: www.tygerauto.com/contact V230511 PROCEDURE: REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. ASSISTANCE IS RECOMMENDED. STEP 1 Start the installation under the Passenger/Right side of the vehicle. a. For "Early" 2019 models, locate the 6 plugs along the bottom edge of the body. Mounting Brackets will bolt to the 1st, 3rd, 4th and 6th threaded mounting holes (Fig 1). Passenger/Right side Installation Pictured Front TYGER LanderX (2) 8mm Hex Bolts (2) 8mm Lock Washers (2) 8mm Flat Washers Front (Fig 3) Attach (1) Passenger/Right Mounting Bracket to the mounting location (Fig 1) Passenger/Right "Early" rocker panel mounting locations (arrows) NOTE: Hold Bracket up to body panel to help determine the correct mounting locations. b. For "Late" 2019 models, all (4) mounting locations will be used. STEP 3 Repeat STEPS 1 & 2 to attach (3) Mounting Brackets to the (3) remaining locations along the rocker panel (Figs 4-7). DO NOT tighten hardware. Passenger/Right side Installation Pictured STEP 2 Remove the plastic plugs from the passenger/right front mounting location. Select (1) Mounting Bracket. Attach the Mounting Bracket to the factory threaded holes with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers (Figs 2 & 3). DO NOT tighten hardware. Front (Fig 4) Passenger/Right front mounting location Remove plugs Front (Fig 2) Remove plastic plugs to uncover threaded inserts Front (Fig 5) Passenger/Right 2nd mounting location 2/3 Front (Fig 6) Passenger/Right 3rd mounting location Front TYGER LanderX STEP 5 Level and adjust the TYGER LanderX, then fully tighten all STEP 6 Repeat STEPS 1-5 to attach the Driver/Left TYGER LanderX. STEP 7 Do periodic inspections to the installation to make sure that all hardware is secure and tight. (Fig 7) Passenger/Right rear mounting location STEP 4 Select the Passenger/Right TYGER LanderX. Attach the TYGER LanderX to the (4) Mounting Brackets with (8) 8mm Combo Bolts (Fig 8). DO NOT tighten hardware. Passenger/Right side Installation Pictured (2) 8mm Combo Bolts Front (Fig 8) Attach Passenger/Right TYGER LanderX to the Mounting Brackets 3/3