Olight Odin GL M User Manual

Product Overview

The Olight Odin GL M is a tactical flashlight with an integrated green laser.

Key Components:

• Magnetic Tailcap
• Tail Switch
• M-LOK Rail Mount
• Magnetic Remote Switch

Specifications

• Max Output (Light): 1500 lumens
• Max Runtime (Light): 168 minutes (High), 6h 30min (Low)
• Max Output (GL Beam): 5mW
• Max Runtime (GL Beam): 90h
• Wavelength (GL Beam): 510-530nm
• Beam Distance (Light): 215m (High), 95m (Low)
• Waterproof Rating: IPX4
• Drop Resistance: 1.5m
• Dimensions: 149mm (L) x 29mm (D) / 5.87in (L) x 1.14in (D)
• Weight: 224g / 7.9oz (Including Battery)
• Battery: 1 x customized 5000mAh 21700 rechargeable lithium battery

Charging

Charging Cable: MCC3 USB Magnetic Charging Cable

Input: USB A - Type DC 5V 2A

Charging Pattern: CC&CV

Max Charging Current: 2A

Voltage of Fully Charged Battery: 4.2V±0.05V

Time to Fully Charge: Approximately 5.5 hours (may vary with USB power source capacity).

Charge Indication: Red light indicates charging; Green light indicates charging completed (battery level > 95%) or disconnected.

Instructions:

1. Connect the USB end of the MCC3 cable to an external USB power source (minimum 10W recommended).
2. Attach the magnetic end of the cable to the charging port of the flashlight.
3. Only use the standard MCC3 cable; it is not compatible with other MCC cables.

Product Installation

M-LOK Rail Mount Installation:

1. Loosen the screws on the M-LOK rail mount.
2. Install the mount in the desired position on the rail and tighten the screws.
3. Slide the flashlight into the rail mount until it clicks.
4. Turn the button 90 degrees clockwise to fix the product.
5. Tighten the rail mount to the flashlight using the provided H1.5 allen wrench.
6. To remove, rotate the button 90 degrees counterclockwise and slide the product out.

Remote Switch Installation

Magnetic Remote Switch:

1. Attach the magnetic remote switch to the tail of the flashlight. Ensure the detent ring of the remote switch is unlocked.
2. Push the ring forward to fix the remote switch.

How to Operate

Light Settings: Rotate the ring at the head of the flashlight to select one of three modes:

• White LED only
• White LED and Green Beam combined
• Green Beam only

Tail Switch Operation:

• Low Light: Lightly press the tail switch.
• High Light: Firmly press the tail switch.
• On/Off: Single click the tail switch (press and release quickly).
• Momentary On: Press and hold the tail switch; the light turns off when the switch is released.

Vibrating Power Indicator

The flashlight vibrates to indicate low battery levels:

• Power < 20%: Vibrates once every 5 minutes.
• Power < 10%: Vibrates once per minute.
• Power < 5%: Vibrates once every 10 seconds.

Safety Precautions

DANGER

• DO NOT shine the light or GL beam directly into human eyes. This may cause temporary blindness or permanent damage.
• DO NOT cover the flashlight's head or place it on the ground when on. The heat may damage the flashlight or cause nearby flammable objects to burn.
• DO NOT leave the light in any type of fabric bag or fusible plastic container under high temperature.
• DO NOT charge the product with any cable other than the MCC3.
• DO NOT use non-protected rechargeable batteries.
• DO NOT use the battery if its wrap is broken.
• DO NOT remove the battery from the flashlight for charging.

WARNING

• Keep out of reach of children.
• DO NOT disassemble the product, as this may cause irreversible damage.
• The tail switch may not function correctly when immersed in seawater or other conductive media. Keep it clean and dry.
• If the light will be stored for a long time or transported, unscrew the tailcap and remove the battery to disconnect the circuit.
• Handle batteries with care. If a battery needs replacement, keep the removed battery in a safe place and do not mix it with conductive metals.
• The flashlight surface may reach 50°C or above when used on high brightness for extended periods.
• The GL beam is bright and blinding – DO NOT shine it at aircraft or vehicles at any distance.

NOTICE

• DO NOT short-circuit the tail switch cap with the surrounding ring. This can cause a weak electric discharge and may lead to complete battery drain if left in this state for too long.
• The GL beam level is Class 3R/Class IIIa, obeying IEC60825-1 standards and complying with 21 CFR 1040.10 AND 1040.11.
• All specifications are based on ANSI/NEMA FL1 Standard tests performed with the included battery fully charged.
• The magnetic tail is easy to attract iron debris. Keep the tail switch cap and surrounding ring clean.
• The setting switch is magnetically sensitive; proximity to magnets may cause interference.
• The white light provides 1500 lumens for 60 seconds, then steps down to 550 lumens within 90 seconds.

Warranty

• Within 30 days of purchase: Contact the original seller for repair or replacement.
• Within 5 years of purchase: Contact Olight for repair or replacement.
• Battery warranty: One year for all rechargeable batteries.
• USB magnetic charging cable warranty: One year.
• For fragile or low-value fittings (e.g., lanyard, clip), contact after-sales support within 30 days of purchase if there are quality issues under normal use. Conditional quality assurance may apply for issues arising after 30 days or under abnormal use.

Customer Support

• USA Customer Support: cs@olightstore.com
• Global Customer Support: customer-service@olightworld.com

Visit www.olightworld.com for the complete product line.

Document Version: 3.0056.6010.9001 B. 11. 19. 2021

Manufacturer: Dongguan Olight E-Commerce Technology Co., Ltd

Address: 4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China.

Made in China