User Manual for J-TECH DIGITAL models including: RS232 HDMI Matrix Switch, RS232, HDMI Matrix Switch, Matrix Switch, Switch
Amazon.com: 8x8 HDMI Matrix Switch 4K 60Hz 4:4:4 HDR HDMI 2.0 HDCP 2.2 | Supports EDID Management, RS232 Serial, IR Remote, Web Interface, Control App, Control 4 Driver by J-Tech Digital [JTECH-8x8-H20B] : Industrial & Scientific
4K 60Hz 8x8 HDMI Matrix Switcher with Coaxial SPDIF Outputs
File Info : application/pdf, 21 Pages, 1.55MB
DocumentDocumentWebsite: www.jtechdigital.com Toll Free: 1-888-610-2818 Email: support@jtechdigital.com USER MANUAL J-Tech Digital® ProAV HDMI2.0 8X8 matrix with IP RS232 Coaxial Model: JTECH-8x8-H20B JTD-ID: 3002 1 Operating Instruction Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. Never spill liquid of any kind on or into this product. Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. Do not attach the power supply cabling to building surfaces. Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. 2 CONTENTS Operating Instruction 1. INTRODUCTION·············································· 4 2. APPLICATIONS················································ 4 3. PACKAGE CONTENTS······································ 4 4. SYSTEM REQUIREMENTS································ 4 5. FEATURES······················································ 5 6. SPECIFICATIONS············································· 5 7. OPERATION CONTROLS AND FUNCTIONS········· 6 7.1 Front Panel ·················································· 6 7.2 Rear Panel·····················································7 7.3 Remote Control ············································· 8 7.4 RS-232 Control ············································15 7.5 Web Control················································· 16 7.6 Micro USB to update firmware....................................19 8. CONNECTION DIAGRAM······························· 20 3 Operating Instruction 1. INTRODUCTION This 8x8 4k HDMI Matrix supports the transmission of video (resolutions up to 4K2K@60Hz, HDCP 2.2, HDMI2.0) and multi- channel digital audio from 8 HDMI sources to 8 HDMI outputs and 8 SPDIF Output. This matrix supports high resolution digital audio formats such as Dolby TrueHD and DTS-HD Master Audio as well as 3D video content. Controllable via Panel buttons, local IR, RS-232, IP or Web GUI. We can provide control drivers for all the major control systems. This unit also supports HDR10 to bring ultimate visual experience. It is designed to save end users' time and energy for they are able to update the system by the creative micro USB interface. In addition, this matrix also allow additional options for integration of third-party control systems, we could provide control drivers for control systems such as Control 4. 2. APPLICATIONS · Video/TV wall display and control · Security surveillance and control · Commercial advertising, display and control · University lecture hall, display and control · Retail sales and demonstration 3. PACKAGE CONTENTS · 1x HDMI Matrix · 1x 12V DC power supply · 1x Remote control · 1x IR Ext RX Cable · 1x mounting kit · 1x CD for control software & user manual 4. SYSTEM REQUIREMENTS · HDMI source equipment such as media players, video game consoles or set-top boxes. · HDMI receiving equipment such as HDTVs, monitors or audio amplifiers. · The use of "Premium High Speed HDMI" cables is highly recommended 4 Operating Instruction 5. FEATURES · HDMI 2.0 version (Support 4K@60Hz YUV4:4:4) · Support 3D · Bandwidth upto 18Gbps · HDCP2.2 input ,HDCP2.2 output · HDCP1.4 input, HDCP1.4 output · Support HDR10 · 8xHDMI Input, 8xHDMI output with 8xSPDIF Audio · Any one of the 8 Ultra HD sources to any one of the 8 Ultra HD displays · Support Dolby True HD and DTS-HD master audio · Micro USB interface for user to upgrade firmware · Controllable via front-panel buttons, IR remote, RS232, IP , Web GUI Control · 1U rack design, easy installment · Unit size: L440XW220XH44.5mm 6. SPECIFACATIONS Bandwidth Resolution Video Input Connectors Video Output Connectors RS-232 serial port Ethernet port (IP control) IR Ext port Rack-Mountable Dimensions(WxHxD) Net Weight Operating Temperature Storage Temperature Power consumption 18 Gbps 480p@60hz,576P@50hz,720P@60hz, 1080P@24hz,1080P@50hz,1080P@60hz,4K@24hz,4K@30hz, 4K@60hz YUV4:2:0, 4K@ 60hz YUV4:4:4 8xHDMI Type A, 19-pin, female 8xHDMI Type A, 19-pin, female DB9, female RJ45, female 1x3.5mm stereo jack Rack ears included L440XW220XH44.5mm 2.8kg 32°F to 104°F (0°C to 40°C) 14°F to 140°F (-10°C to 60°C) 23W(Max) 5 Operating Instruction 7. OPERATION CONTROLS AND FUNCTIONS 7.1 Front Panel 1 IR WINDOW: Accepts IR signals from the included IR remote for control of this unit only. 2 OUTPUT 1~8 & INPUT 1~8: Press output keys (1~8) to select output source; then press input buttons to select input source (1~8). And also could press and hold Input & Output buttons for 3 second to set up below functions: Locking & Unlocking: Press and hold the Input8 for 3 seconds to lock all button functions on the front panel. Press and hold Input8 for 3 seconds again to release the lock function. Checking & Setting IP Address / DHCP: Press and hold the Input7 for 3 seconds to enter into the mode of checking IP address and DHCP. Press and hold Input5 for 3 seconds to Exit. Press below buttons shortly to revise the IP address and DHCP accordingly. Press Input1 button to let cursor move LEFT Press Input2 and/or Output2 button to revise the data Press Input3 button to let cursor move RIGHT Press Output1 button to confirm revising Checking & Setting EDID: Press and hold the Input6 for 3 seconds to enter into the mode of checking EDID. Press and hold Input5 for 3 seconds to Exit. Press below buttons shortly to revise the EDID accordingly. Press Input2 and/or Output2 button to revise the data Press Output1 button to confirm revising 6 7.2 Rear Panel Operating Instruction 1 IP CONTROL: Connect directly, or through a network switch, to your PC or laptop to control the unit via telnet/Web GUI. 2 RS232: Connect directly to a PC, laptop or other serial control device to send RS-232 commands to control the unit 3 MICRO USB: This slot is reserved for firmware update use only 4 IR IN: Connect to the provided IR Extender to extend the IR control range of the unit. Ensure that the remote being used is within direct line-of-sight of the IR Extender. 5 SPDIF Audio Output: Audio output is from the selected HDMI source 6 DC POWER: Plug the 12V DC power adapter into the unit and connect it to an AC wall outlet for power. 7 INPUT 1~8: Connect to HDMI source equipment such as media players, game consoles or set-top boxes. DVI sources are supported with the use of an HDMI to DVI adapter. 8 OUTPUT 1~8: Connect to HDMI TVs, monitors or amplifiers for digital video and audio output. 7 7. 3 Remote Control Description 1 Standby Mode. 2 OUTPUT-X select INPUT-Y: Press OUTPUT-X (X means 1 to 8 of outputs) Press INPUT-Y (Y means 1 to 8 of inputs) 3 All outputs select INPUT-Y: Press ALL button in zone OUTPUT Press INPUT-Y button (Y means 1 to 8 of inputs), then INPUT-Y switched to ALL OUTPUTS. 4 Cancel Button: Cancel the switching operation 5 PTP button: Mirror all inputs and outputs (Ex. Input 1 to output 1, input 2 to output 2, etc): Press PTP button in Zone OUTPUT. Operating Instruction RS232 Pin Assignment Matrix PIN Assignment 1 NC 2 Tx 3 Rx 4 NC 5 GND 6 NC 7 NC 8 NC 9 NC Remote Control Console PIN Assignment 1 NC 2 Rx 3 Tx 4 NC 5 GND 6 NC 7 NC 8 NC 9 NC 8 Operating Instruction 7.4. RS232 Control Software control Connect the 8x8 Matrix to PC with a RS232 cable, open the software on your PC. On the COM Setting session, select the COM port according to your PC and click "Connect" to get connected. On this COM setting session, you can also change the Device name, Device name support up to 16 characters. Save or edit your status by clicking the Edit button. Come to Port Set session to select or switch your input sources for each output, We can read the current status by clicking the "Status" button, or Clear our historical operating record by clicking "Clear" button. The right down blank shows the operating history. Picture 1 9 Operating Instruction The EDID session helps us to Read and Configure EDID for each input, such as HDR, 3D, Data rates and Audio channel. Picture 2 The IP configure session helps to read and configure the IP address and MAC of the Matrix. Check DHCP if you want the router to assign an IP for the Matrix automatically . Picture 3 10 Operating Instruction The Net Config session allows us to configure the PC and Matrix in the same LAN with the IP Address and connection. Click "Net config" "Connect" "Search Device" "Sel Device Number" "Connect" then you can see the device name, it means successful connection . Picture 4 You can also click "IE", easy and click to enter into web. Picture 5 11 Operating Instruction The last session is System Config, which allows power ON/OFF or reset, default the Matrix. Picture 6 12 Command Control 1). Open CommUart Assistant. 2). Comport setting: Baud Rate: Parity: Data Bits: Stop Bits: TCP/UDP Port: 115200 bps None 8 bit 1 bit 5000 3). Enter Port Command in Send options. Operating Instruction Picture 7 13 Operating Instruction 4). Command Command Function Note @T 04 00 01 02 03 ·· PTP Function Mirror all inputs and outputs (Ex. Input 1 to output 1, input 2 to output 2, etc) @T 50 # Reboot @T 51 # Restore Setting Factory @T 0F 00 # Standby 00: Standby Mode 01: Cancel "Standby Mode" 5). Select HDMI input for HDMI output Command Description 00 Output1 01 Output2 02 Output3 03 Output4 11 Output5 12 Output6 13 Output7 14 Output8 04 All Output 00 Input1 01 Input2 02 Input3 03 Input4 04 Input5 05 Input6 06 Input7 07 Input8 E.g: @T 00 00 #: Output 1 display Input1 Output 1 Input1 14 Operating Instruction 6). EDID Setting @T XX AA BB #: Parameter Description: XX for configuration of "INPUT EDID" Command 05 06 07 Description Input1 Input2 Input3 08 15 16 17 18 Input4 Input5 Input6 Input7 Input8 AA for selecting "Video Mode" Command 00 01 Description 1080P 4K2K_30 02 4K2K_60(YC420) 03 4K2K_60(YC444) BB for selecting belowing function Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 HDR 48Bit 36Bit 30Bit 7.1CH 5.1CH 2CH 3D 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 "1" : select the function, "0" : not select the function. E.g: 11001001: HDR, 48Bit, 7.1CH, 3D Chang Binary code "11001001" to hexadecimal format "C9". E.g: @T 05 03 C9 # The EDID of input 1 is: 4K2K_60(YC444)HDR48Bit7.1CH3D. 15 Operating Instruction 7.5. Web Control 1) . Connect the HDMI Matrix and PC to the LAN under the Matrix DHCP Mode. 2) . Open the PC tool (included in the CD). 3). Search the IP address of HDMI Matrix, please refer to picture 4 & picture 5. 4). Open the web browser and enter the IP address you searched, then you can set the function as below pictures: Picture 8: Login Page Default User name: Admin Default Password: Admin Picture 9: Port Setting Page 16 Operating Instruction Picture 10: EDID Setting Page Picture 11: IP Configuration Page 17 Operating Instruction Picture 12: Port Name Setting Page Picture 13: Login info setting Page Picture 14: Firmware Upgrade Page 18 Operating Instruction 7.6 Micro USB to update firmware Connect 8x8 HDMI Matrix to PC or laptop with Micro USB cable after matrix is powered on. Open the "updated software' which has been downloaded in our CD. And then click " Search" " Port Sel" ( to choose correct port) "Connect" (It will show "S3RLC" when connect successfully ) "Load FW File" "Update" Please do not power off or disconnect when it is updating the FW file. S3RLC Picture 15: software updated 19 8. CONNECTION DIAGRAM Operating Instruction 20 21