Spectravision PL-REM-200 LED Pool Light Remote Control
OWNER'S MANUAL
Long range DuraLink™ version
Technical Specifications
Electrical Specifications
| Parameter | Value |
|---|---|
| Nominal Input voltage | 230 VAC 50 Hz |
| Output voltage on Lamp Output | 12 VAC |
| Max output current on Lamp Output | 16,7 A |
| Max rating Relay Contact A and B | 14A 250VAC |
| Resistive Load | 14A 30VDC |
| Inductive Load | 6A 250VAC 6A 30VDC |
| Transformer VA rating | 200VA |
| Fuse type | 5x20mm cartridge fuse, 5A 250V slow blow/time lag |
| Frequency band transmitter | 868 MHz |
| IEC Protection Class | Class II |
General Specifications Controller
| Parameter | Value |
|---|---|
| Ambient air temperature | 0°C ... +40°C |
| Humidity | 10% ... 90% RH, non condensing |
| Dimensions | 195x194x90 mm |
| Weight | 3,2 kg |
| Ingress protection rate | IP54 |
Box Contents
The box contains the following items:
- PL-REM-200 controller
- Handheld transmitter (DuraLink™ version)
- Spare battery (type A23 12V)
- Screws (4x) & wall plugs (4x)
- Owner's manual
A visual representation shows the controller unit (1), the handheld transmitter (2), a battery (3), screws and wall plugs (4), and an open owner's manual (5).
Installation Instructions
- Connect a 230VAC power source to the “220-240VAC INPUT” terminal.
- Connect the swimming pool lights to the "Lamp 12VAC output" terminal.
- ⚠️ Make sure the total load of pool lights does not exceed 200Watt.
Optional: The "Switch A" & "Switch B" terminals can be used to control auxiliary circuits like a pool cover or garden lights.
Diagram shows the PL-REM-200 controller with connections for:
- Green status LED
- Spare fuse
- Lamp 12VAC Output
- Switch A (connected to Pool cover)
- Switch B (connected to Garden lights)
- 220-240V AC INPUT (connected to 230VAC power source)
Pairing Handheld Transmitter & Controller
The handheld transmitter is pre-paired from the factory. The PL-REM-200 can be paired with up to 6 handheld transmitters. If issues arise, manual pairing can be performed:
Manual Pairing Process:
- Ensure the PL-REM-200 is connected to a power source.
- Press the pairing button on the small circuit board inside the controller for at least 5 seconds. The LED will start to blink fast.
- Within 25 seconds, press any button on the handheld transmitter.
Confirmation:
- If paired correctly, the LED will flash slowly 5 times.
- If the PL-REM-200 pairing memory is full (6 devices already paired), the LED will flash 15 times.
To unpair all handheld transmitters:
Push the pairing button for at least 5 seconds, then wait for 25 seconds without further action. The pair memory will be erased, and the red LED will flash 5 times on/off.
Diagram indicates the location of the pairing button and the red LED on the handheld transmitter.
Handheld Transmitter Functions
- ON/OFF Button: Toggle the lamps ON/OFF.
- Color Button: Go to the next color scenario.
- Button A: Toggle Output A ON/OFF.
- Button B: Toggle Output B ON/OFF.
Replacing Transmitter Battery
- Remove the Phillips head screw and open the transmitter.
- Replace the battery, ensuring correct polarity.
- Battery type: A23 12V.
Diagrams illustrate opening the transmitter and replacing the battery with correct polarity (+ and - symbols indicated).
Troubleshooting
| PROBLEM | SOLUTION |
|---|---|
| The controller doesn't react to transmitter commands |
|
| The pool lights don't work |
|
Contact Details
Propulsion Systemsbvba
Dooren 72
1785 Merchtem, Belgium
Tel: +32 2 461 02 53
Fax: +32 2 706 59 60
Website: www.propulsionsystems.be
Email: info@propulsionsystems.be
Authorized Distributor:
KOI GARTEN
Ihr Teich und Pool Profi
Koigarten Müller
Randenstr. 4
88605 Meßkirch
www.koigarten-mueller.de
We reserve the right to change all or part of the contents of this document without prior notice.
Koigarten Müller - Trommelfilter - Teichpumpen - Koifutter
