Instruction Manual for IQ AMERICA models including: IQ34, IQ34 Portable LED Alert Wireless Door Chime Kit, Portable LED Alert Wireless Door Chime Kit, LED Alert Wireless Door Chime Kit, Alert Wireless Door Chime Kit, Wireless Door Chime Kit, Door Chime Kit, Chime Kit, Kit
IQ Group (WuNing) Ltd. IQ34 2BGCM-IQ34 2BGCMIQ34 iq34
File Info : application/pdf, 3 Pages, 1.66MB
DocumentDocumentEN Instruction Manual To get the online version of instruction manual for English, French and Spanish, please visit: https://iqamerica.com/manuals/ wl/doorbells or scan QR code. Setup: IQ34 IQ34 Portable LED Alert Wireless Door Chime Kit IQ34 INSMTARNUUCATLION Screw x 4 Chime Pushbutton x 2 CR2032 Instruction Double-sided Wall Plug Battery x 2 Manual Tape x 2 x 4 Battery Caution & Disposal Information: 1. Do not mix old and new batteries. 2. Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Ni-Cad, NiMH, or Lithium) batteries. 3. Do not dispose of batteries in fire. 4. Batteries should be recycled or disposed of as per local guidelines. 1: Place a small flat screwdriver into the locking clip on the base of the pushbutton. 2: Gently twist. 3: The back plate will unclip. 1: Insert CR2032 battery (Supplied) into the battery holder. For WD-2060-T, insert batteries into 2 pushbuttons. 2: Make sure the positive side is facing upwards. 3: Replace back plate. Warning: Make sure that the batteries are replaced correctly to avoid battery failure. Only replace with same or equivalent type. 1: Remove the battery cover of the Door Chime. 2: Insert 3 X 1.5V Size 'AA' batteries (Not Supplied). 3: Make sure the Positive/Negative terminals match the internal markings. 4: Chime will `Beep' on Start up. 5: Replace the battery cover. WARNING INGESTION HAZARD: This product contains a button cell or coin battery. DEATH or serious injury can occur if ingested. A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours. KEEP new and used batteries OUT OF REACH of CHILDREN. Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body. Within WD-2010 / WD-2060-T WD-2010-F / WD-2060-TFA 1: Press and hold the `VOL' button on the Door Chime until the Chime goes `Beep Beep' (6 seconds) 2: Press the Pushbutton within 60 seconds to code the pushbutton to the chime. For WD-2060-T, press the second pushbutton within 60 seconds to code the pushbutton to the chime. Or refer to Adding Additional Pushbutton section. 3: The Chime will ring to confirm setup. Note: Maximum of 6 pushbuttons can be coded to a single Chime. 0424E1 Functions: Melody Selection To select a melody for the Door Chime 1: Remove the Back Plate from the pushbutton. 2: Press the Melody Select button. 3: The chime will play the newly selected sound. 4: Press again to select the next melody. Note: For Front/Back door setup, select a different melody in one of the pushbuttons. 6 Selectable Melodies 1: Tubular 3-Note 3: Tubular 2-Note 2: Big Ben 4: Solo 5: Tubular Score 6: Clarinet Volume Control: To select the Chime Volume level, press the `VOL' button on the chime. There are 4 selectable volume levels, the Door Chime is pre-set to loudest volume setting. Default Volume LED Flash Alert: WD-2010-F / WD-2060-TFA Adding Additional Chime / Pushbutton Additional Chime To add an additional Chime unit to the Door Chime kit 1: Press and hold the `VOL' button on your New Door Chime, until the Chime goes `Beep Beep' (6 seconds) 2: Press the Pushbutton within 60 seconds to pair the additional Chime to the Pushbutton. 3: Chime will ring to confirm setup, wait 60 seconds for the Chime to exit the learning mode before pressing the pushbutton again. Additional Pushbutton To add an additional Pushbutton to the Door Chime kit 1: Press and hold the `VOL' button on your Door Chime until the Chime goes `Beep Beep' (6 seconds) 2: Press the Pushbutton within 60 seconds to code the additional Pushbutton to the Chime. 3: Chime will ring to confirm setup, wait 60 seconds for the Chime to exit the learn mode before repressing the pushbutton. For Front/Back door setup, select a different melody in one of the pushbuttons - See Melody Selection. Note: Maximum of 6 pushbuttons can be coded to a single Chime. Avoid locating the Pushbutton/Chime on or directly near metallic surfaces as this may reduce the operation range. UPVC Door Frames: When locating the pushbutton onto a UPVC door, always check the operating performance before final installation, internal metal frame may affect performance. Note: Try adjusting the location of the Pushbutton to the Left/Right or place on external wall. Installation Guide: Pushbutton FLASH: Button Press to switch the LED Alert On or Off FLASH: ON LED Light will flash FLASH: OFF Chime will `Beep' NOTE: With LED Alert enabled, the LED light will flash after the ringtone during each activation. `Adhesive Tab' 1: Using back plate as a template. 2: Make sure UP arrows point UP. 3: Select ideal position for best performance. 4: Stick adhesive tab to back plate & stick into position. 5: Clip the Pushbutton on to the back plate making sure the Pushbutton "Clicks" in to place. NOTE: Pushbutton can be screwed into position using the two hole marks as guides on the back plate. Installation Guide: Chime Place the door Chime within the operating range of the pushbutton. The transmission range of the wireless signal may be reduced while passing through Walls, Doors and Ceilings, etc. Chime unit for INDOOR use only. IMPORTANT: There are no serviceable parts, do not repair. The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. Children should be supervised to ensure that they do not play with the appliance. Diagram for illustration purposes only. Specification Pushbutton Power: 1 x CR2032 3V DC Battery (Included) IP44 Weather Resistant Portable Door Chime Power: 3 x 'AA'/LR6 1.5V Batteries Range: 328 ft (100 m) Indoor Use Only Changing Batteries Resetting Chime: Pushbutton 1: Remove back plate from the Pushbutton. 2: Remove old battery from the holder. 3: Replace with new 'CR2032' 3V battery. 4: Insert into holder making sure '+' is facing up. 5: Test Chime Kit. Chime Unit 1: Remove Batteries. 2: Insert new batteries, 3 X 1.5V size 'AA'. 3: Make sure Positive/Negative match the internal markings. 4: Wait 60 seconds before testing the Chime Kit. Always dispose of old batteries in an environmentally friendly way. Trouble Shooting In case the door chime does not sound, please check the following: a) Dead batteries in either Pushbutton or Door Chime. b) Wrong battery polarity in either Pushbutton or Door Chime. c) Pushbutton and Door Chime are not paired together, see setup guide. d) Materials in between the Pushbutton & Chime will reduce the operating range, move the Door Chime closer to the Pushbutton. e) Wireless devices can be affected by external sources e.g. wireless home alarms or power transformers/adapter. IQ America Three Year Warranty This is a "Limited Warranty" which gives you specific legal rights. You may also have other rights which vary from state to state and province to province. For a period of three years from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you. To obtain a refund or a replacement, return the product to the place of purchase. NOT COVERED: Repair service, adjustment and calibration due to misuse, abuse or negligence. Unauthorized service or modification of the product or of any furnished component will void this warranty. This warranty does not include reimbursement for inconvenience, installation, setup time, loss or use or unauthorized service. This warranty covers only IQ America products and is not extended to other equipment and components that a customer uses in conjunction with our products. This warranty is expressly in lieu of all other warranties, express or implied, including any warranty, representation or condition of merchant ability of that the products are fit for any particular purpose or use, and specifically in lieu of all special, indirect or incidental or consequential damages. Repair or replacement shall be the sole remedy of the customer and there shall be no liability on the part of IQ America for any special, indirect, incidental or consequential damages, including but not limited to any loss of business or profit, whether or not foreseeable. Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Retain receipt for warranty claims. Hold For Hold For Reset Chime unit to factory settings. 1: Press and hold the `VOL' button on your Door Chime until the Chime goes `Beep Beep' (6 seconds) 2: Release the `VOL' button. 3: Re-press and hold the `VOL' button on your Door Chime until the Chime goes `Beep' (6 seconds) 4: The Chime is now reset. Note: This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. To comply with FCC RF exposure requirements, this device and its antenna must not be co-located or operated in conjunction with any other antenna or transmitter. Helpline Customer service number: For problems or questions, please call us at 1-800-296-1869 Instructions: Please retain this instruction manual for future reference