Manuals+
Sun Glow Motor Programming Instructions: Setup Guide

Programming Instructions

MOTOR INFORMATION

1. Ensure the motor is protected from damages during transportation, storage, installation, or misuse, as these can cause it to not work properly.

2. Charge the motor every 6 months to ensure optimal performance.

3. If the battery charge is low, the motor will beep 10 times to prompt charging.

4. The maximum running time of the motor is 6 minutes. After this period, the motor will enter sleep mode. It will remain in wake-up/programming mode if restarted.

Programming information resides within the motor. Each motor can store up to 20 copied channels.

CONTROL RANGE

⚠️ SIGNAL STRENGTH AND RANGE MAY VARY DEPENDING ON THE ACTUAL ENVIRONMENT.

The operating temperature range for the motor is between -10°C and 55°C.

Diagram Description: A visual representation shows a roller shade, a remote control emitting a signal (L1), and obstructions affecting the signal (L2).
  • Range in Open Area (L1): 200 meters
  • Range with Obstructions (L2): 35 meters
  • Emission Frequency: 433.92/868 MHz

RECHARGING THE MOTOR

To recharge the motor's battery, connect the SG DC charger to the motor head charging jack and plug the charger into a standard electrical outlet. The charger's indicator light will turn green when the battery is fully charged (it is red while charging).

Alternatively, the SG Solar Panel can be used to keep the battery constantly charged when exposed to sufficient sunlight.

⚠️ IF PURCHASING MORE THAN ONE CHARGER, PLEASE ENSURE THE OUTPUT VOLTAGE ON THE CHARGER AND MOTOR MATCH.

Visuals: A charger light indicator, a SG Solar Panel, and the motor head with its charging jack are depicted. The "CE" mark is also visible.

MOTOR BUTTON LAYOUT

Visual Description: The motor head is shown with a "Motor Setting Button" and a "Charging Jack".

REMOTE BUTTON LAYOUT

The system includes various remote control options:

15 Channel Remote

Visual Description: A handheld remote with a display showing "15". Buttons include: "Up Button", "Stop Button", "Down Button", and "Right/Left Buttons" for switching channels. A "P2 Setting Button" is also present. The back of the remote shows a compartment for a CR2450 Lithium Cell battery and indicates that a cover can be removed to expose a standard remote back.

15 Channel Wall Switch

Visual Description: A wall-mounted switch with a display showing "15". Buttons include: "Up Button", "Stop Button", "Down Button", and "Right/Left Buttons" for switching channels. A "P2 Setting Button" is visible.

15 Channel Glass Wall Switch

Visual Description: A wall-mounted glass-faced switch with a display showing "15". Buttons include: "Up Button", "Stop Button", "Down Button", and "Right/Left Buttons" for switching channels. A "P2 Setting Button" is visible, which can be activated when held together with another button.

BEFORE YOU BEGIN

? STOP

  1. Motors are shipped in factory default mode with no limits set.
  2. Channel "0" cannot be programmed on a multi-channel remote; it is reserved as a master channel for all motors.
  3. Select the desired channel before activating wake-up mode, basic, or advanced programming settings.

STEP 1: PREPARING FOR PROGRAMMING

WAKE-UP MODE

(Must be done before Basic & Advanced Programming)

This step is required to establish the connection between the remote and the motor. Ensure operations are performed within 10 seconds of each other; otherwise, the program will cancel, and the motor will revert to default mode. Follow the steps below to wake up the motor.

Note: No limits are assigned during wake-up mode.

Programming Sequence:
  1. HOLD the motor setting button.
  2. Wait for the motor to jog once ([motor jog] 1X).
  3. RELEASE the button to activate the motor.
  4. The motor will beep once ([motor beep] 1X).
  5. HOLD the motor setting button again.
  6. Wait for the motor to jog twice ([motor jog] 2X).
  7. The motor will beep three times ([motor beep] 3X).
  8. Setup is complete (✔️).

Test Shade: Move the shade by holding the up or down button to confirm the motor operates on the correct channel and moves in the desired direction.

⚠️ Do not let the shade crash into the valance or unroll completely from the tube.

SWITCH DIRECTION

Programming Sequence:
  1. HOLD TOGETHER the up and down buttons.
  2. Wait for the motor to jog once ([motor jog] 1X).
  3. Setup is complete (✔️).

Test Shade: Move the shade up and down to ensure the direction has been changed correctly.

⚠️ Do not let the shade crash into the valance or unroll completely from the tube.

STEP 2: BASIC PROGRAMMING

SETTING MOTOR LIMITS

This allows you to set two positions: the upper and lower limits for each shade per channel. During limit setting, operations must be performed within 2 minutes of each other; otherwise, the program will cancel, and the motor will return to wake-up mode. Follow the steps below to set motor limits.

Setting Upper Limit:
  1. Navigate to the desired upper limit position.
  2. HOLD TOGETHER the up and down buttons.
  3. Wait for the motor to jog twice ([motor jog] 2X).
  4. The motor will beep three times ([motor beep] 3X).
  5. Setup is complete (✔️).
Setting Lower Limit:
  1. Navigate to the desired lower limit position.
  2. HOLD TOGETHER the up and down buttons.
  3. Wait for the motor to jog twice ([motor jog] 2X).
  4. The motor will beep three times ([motor beep] 3X).
  5. Setup is complete (✔️).

Note: Holding the up or down buttons will move the shade automatically.

Test Shade: Move the shade up and down to test the upper and lower limits. Refer to "Adjusting Motor Limits" for fine-tuning if necessary.

STEP 3: ADVANCED PROGRAMMING

ADJUSTING MOTOR LIMITS

This allows fine-tuning of the previously set upper or lower limits.

Adjusting Upper/Lower Limit:
  1. Navigate to the desired upper or lower limit position.
  2. HOLD TOGETHER the up and down buttons.
  3. Wait for the motor to jog once ([motor jog] 1X).
  4. The motor will beep once ([motor beep] 1X).
  5. PRESS the adjust limit button (represented by an up or down arrow).
  6. Setup is complete (✔️).

Alternatively, holding the up or down buttons will move the shade automatically.

SETTING A PREFERRED POSITION

This allows you to set a third limit position for the shade per channel.

⚠️ WHILE IN TILT FUNCTION, THE SHADE WILL GO TO THE LOWER LIMIT FIRST AND THEN PROCEED TO THE PREFERRED POSITION.

Programming Sequence:
  1. Navigate to the desired preferred position.
  2. PRESS the P2 button on the remote.
  3. The motor will jog once ([motor jog] 1X).
  4. The motor will beep once ([motor beep] 1X).
  5. PRESS the P2 button again.
  6. The motor will jog once ([motor jog] 1X).
  7. The motor will beep once ([motor beep] 1X).
  8. PRESS the P2 button a third time.
  9. The motor will jog twice ([motor jog] 2X).
  10. The motor will beep three times ([motor beep] 3X).
  11. Setup is complete (✔️).

After setup, holding the stop button will move the shade to the preferred position. You can program different preferred positions to separate channels on a 15-channel remote.

DELETING A PREFERRED POSITION

Programming Sequence:
  1. Navigate to the preferred position.
  2. PRESS the P2 button on the remote.
  3. The motor will jog once ([motor jog] 1X).
  4. The motor will beep once ([motor beep] 1X).
  5. PRESS the P2 button again.
  6. The motor will jog once ([motor jog] 1X).
  7. The motor will beep once ([motor beep] 1X).
  8. PRESS the P2 button a third time.
  9. The motor will jog once ([motor jog] 1X).
  10. The motor will beep once ([motor beep] 1X).
  11. Setup is complete (✔️).

STEP 3: ADVANCED PROGRAMMING (CONTINUED)

SPEED ADJUSTMENT

Each motor has three speeds. Follow the diagram to adjust the speed.

Speed Adjustment Sequence (Gear Up):
  1. Press P2 button.
  2. Motor jogs 1X ([motor jog] 1X).
  3. Motor beeps 1X ([motor beep] 1X).
  4. Press the Up button.
  5. Motor jogs 1X ([motor jog] 1X).
  6. Motor beeps 1X ([motor beep] 1X).

Speed Adjustment Sequence (Gear Down):

  1. Press P2 button.
  2. Motor jogs 1X ([motor jog] 1X).
  3. Motor beeps 1X ([motor beep] 1X).
  4. Press the Down button.
  5. Motor jogs 1X ([motor jog] 1X).
  6. Motor beeps 2X ([motor beep] 2X).

TILT MODE INCREMENTAL MOVEMENT

Tilt mode is used for fine adjustment of the shade in small increments. It is most effective when programmed with a standard button remote. Follow the steps below to set the shade in tilt mode or remove it.

Note: Tilt mode remains active in all modes (except Step 2: Basic Programming) unless removed.

Recommended with: Interlude / Banded shades, Illusions / Sheer shades.

Setting Tilt Mode:
  1. HOLD TOGETHER the up and down buttons.
  2. Wait for the motor to jog once ([motor jog] 1X).
  3. PRESS the stop button.
  4. The motor will beep once ([motor beep] 1X).
  5. Setup is complete (✔️).
Deleting Tilt Mode:
  1. HOLD TOGETHER the up and down buttons.
  2. Wait for the motor to jog once ([motor jog] 1X).
  3. PRESS the stop button.
  4. The motor will jog twice ([motor jog] 2X).
  5. The motor will beep three times ([motor beep] 3X).
  6. Setup is complete (✔️).

Test Shade: Press the up or down buttons repeatedly for fine adjustment. To move the shade automatically, hold the up or down buttons and release once the shade begins to move.

STEP 3: ADVANCED PROGRAMMING (CONTINUED)

COPYING, DELETING OR GROUPING WITH A REMOTE

The following outlines methods to copy, delete, or group channels using separate remotes.

Remote Scenario Chart:
  • Option 1: 15 Grouped Channels or 1-15 Separate Channels.
  • Option 2: 15 Grouped Channels or 1-15 Separate Channels.
  • Option 3: 1 Channel.
  • Option 4: 1 Channel.

Separate channels can also be programmed within a single 15-channel remote.

COPYING/GROUPING CHANNELS

Programming Sequence:
  1. Using the original remote or channel, PRESS the P2 button.
  2. Motor jogs 1X ([motor jog] 1X).
  3. Motor beeps 1X ([motor beep] 1X).
  4. Using the original remote or channel, PRESS the P2 button again.
  5. Motor jogs 1X ([motor jog] 1X).
  6. Motor beeps 1X ([motor beep] 1X).
  7. Using the new remote or channel (to be copied or grouped), PRESS the P2 button.
  8. Motor jogs 2X ([motor jog] 2X).
  9. Motor beeps 3X ([motor beep] 3X).
  10. Setup is complete (✔️).

DELETING CHANNELS

Note: This function only works on previously copied/grouped channels.

Programming Sequence:
  1. Using the original remote or channel, PRESS the P2 button.
  2. Motor jogs 1X ([motor jog] 1X).
  3. Motor beeps 1X ([motor beep] 1X).
  4. Using the original remote or channel, PRESS the P2 button again.
  5. Motor jogs 1X ([motor jog] 1X).
  6. Motor beeps 1X ([motor beep] 1X).
  7. Using the new remote or channel (to be deleted), PRESS the P2 button.
  8. Motor jogs 1X ([motor jog] 1X).
  9. Motor beeps 3X ([motor beep] 3X).
  10. Setup is complete (✔️).

DELETING OR TRANSFERRING GROUPS OF MOTORS

⚠️ DELETING OR TRANSFERRING GROUPS OF MOTORS ARE RECOMMENDED TO BE DONE USING THE ORIGINAL REMOTE THAT WAS SET UP.

Activation Sequence:
  1. HOLD the motor setting button.
  2. Wait for the motor to jog once ([motor jog] 1X) then RELEASE to activate this motor.
  3. Motor beeps 1X ([motor beep] 1X).
  4. HOLD the motor setting button again.
  5. Wait for the motor to jog twice ([motor jog] 2X).
  6. Motor beeps 3X ([motor beep] 3X).
  7. Setup is complete (✔️).

PERFORM FACTORY RESET ON MOTOR

⚠️ Only perform a motor reset if necessary.

Reset Sequence:
  1. HOLD the motor setting button until the motor jogs 4X.
  2. RELEASE the button.
  3. Motor beeps 4X ([motor beep] 4X).
  4. Setup is complete (✔️).

STEP 3: ADVANCED PROGRAMMING (CONTINUED)

MOTOR SHIELDING

This mode allows a motor's wireless radio signal to be temporarily disabled to save battery life.

Disabling Signal:
  1. HOLD the motor setting button.
  2. Wait for the motor to jog twice ([motor jog] 2X) then RELEASE.
  3. Motor beeps 2X ([motor beep] 2X).
  4. Setup is complete (✔️).
Enabling Signal:
  1. HOLD the motor setting button.
  2. Wait for the motor to jog twice ([motor jog] 2X) then RELEASE.
  3. The motor will automatically move to its previously assigned limit.
  4. Setup is complete (✔️).

⚠️ If no limits are set, the motor will not move when the signal is enabled.

OPERATING SHADE AT MOTOR HEAD

This mode allows you to operate the shade if the remote is missing or lost.

Operation Sequence:
  1. HOLD the motor setting button.
  2. Wait for the motor to jog twice ([motor jog] 2X) then RELEASE.

Note: Pressing the motor setting button while the shade is moving can also stop the motor.

SWITCHING DIRECTION AT MOTOR HEAD

The direction of the shade movement can be changed after limits have been set.

Direction Change Sequence:
  1. HOLD the motor setting button.
  2. Wait for the motor to jog three times ([motor jog] 3X) then RELEASE.
  3. Motor beeps 3X ([motor beep] 3X).
  4. Setup is complete (✔️).

⚠️ Test Shade: Move the shade up and down to ensure the direction has been changed correctly.

Models: Programming Resides with the Motor, Programming, Resides with the Motor, Motor

PDF preview unavailable. Download the PDF instead.

Programming EN Adobe PDF Library 15.0 Adobe InDesign CC 14.0 (Windows)

Related Documents

Preview Roller Shade Curved Cassette & Compact Curved Cassette Installation Guide
Step-by-step installation instructions for Sun Glow Roller Shades with Curved Cassette and Compact Curved Cassette. Includes safety warnings and bracket mounting guidance.