Extron - The AV Technology LeaderExtron Electronics
User Guide for Extron models including: SW4, Four Input HDMI Switcher, Input HDMI Switcher, HDMI Switcher, SW4, Switcher
File Info : application/pdf, 4 Pages, 972.65KB
DocumentDocumentSW USB Pro Series · Setup Guide GuosestrpoegwcupiwifidrIwoceMda.,eutiixncPotstnrtoOtsaonlbl.RtacehtofTieoomrAnpefoioNncwroseTttnrhrnu:esecocctuiotorimncngesp.,ltehatneed The SW USB Pro Series switchers make it possible for two or four host computers to share and switch among up to four peripheral USB devices, such as USB storage devices, USB cameras, keyboards, and mice. The switchers support USB 3.2, 2.0, and 1.x host and peripheral devices, with data rates up to 10 Gbps. They are compatible with all major computer operating systems. The SW USB Pro Series provide control via front panel buttons, USB, Extron Product Control Software (PCS), Ethernet, RS232, and autoswitching for integration with any control system. Front panel LED indicators provide immediate visual confirmation of signal presence for each input and output. HDMI Extron Cable Cubby 100 Cable Access Enclosure MODEL 80 Laptop USB Extron SW2 USB Pro SuperSpeed USB Switcher USB CHARGER USB Camera POWER STANDBY USB Mic USB POWER 12V --A MAX HOSTS SS 10G 1 2 USB-C USB-C USB USB DEVICES SS 10G 1 2 3 900 mA 1.5A 4 USB HID USB-C 100 mA REMOTE RS-232 Tx Rx G SW2 USB PRO LAN R USB USB Mouse Keyboard FLAT PANEL Display HDMI PC Figure 1. Application Diagram This guide provides instructions for an experienced installer to set up and operate these switchers. For full installation, configuration, and operation details, see the SW USB Pro Series User Guide, available at www.extron.com. 1 SW USB Pro Series · Setup Guide (Continued) Rear Panel Features and Connections POWER 12V 1.6A MAX HOSTS SS 10G 1 2 USB-C USB-C DEVICES SS 10G 1 2 3 900 mA 1.5A 4 USB HID USB-C 100 mA REMOTE RS-232 Tx Rx G SW2 USB PRO LAN R AB DE F Figure 2. Rear Panel -- SW2 USB Pro GH I POWER 1 12V 1.6A MAX USB-C HOSTS SS 10G 2 3 USB-C SW4 USB PRO DEVICES REMOTE SS 10G USB HID 4 1 2 3 LAN 900 mA RS-232 R 1.5A 4 USB-C 100 mA Tx Rx G AB C DE F Figure 3. Rear Panel -- SW4 USB Pro GH I A 2-pole DC Power connector B USB-C host connectors C USB Type B host connectors (SW4 USB Pro only) D Device 1 -- USB-C connector for USB 3.2, 2.0, and 1.x E Device 2 -- USB Type A connector for USB 3.2, 2.0, and 1.x F Outputs 3 and 4 -- USB Type A connectors for USB 2.0 and 1.x G Remote RS-232 port H LAN (Ethernet) connector I Reset (R) button and LED Installation Steps 1. (Optional) Mount the switcher to a rack shelf or furniture. 2. Connect host PCs to the SW USB Pro USBC input connectors (see figure 2 or 3, B). The USBC host connectors do not provide power to the connected host PCs. 3. Connect one or more peripheral USB devices (for example, keyboards, mice, or USB cameras) to the SW USB Pro output device ports (D through F). If host emulation will be used, attach a standard keyboard or mouse to USB host port 3 or 4 (C). If host emulation is not used, connect devices to any desired port. 4. (Optional) Connect an RS232 cable between the SW USB Pro RS232 port (G) and a host computer or control system, or connect the SW USB Pro Ethernet port (H) to the network via a standard Ethernet cable (see the SW USB Pro Series User Guide, available at www.extron.com). Default LAN settings: · Rear panel LAN IP address -- 192.168.254.254 · Front Panel USB-C port IP address -- 203.0.113.22 at port 22023 · Subnet mask: 255.255.255.0 · Gateway: 0.0.0.0 · DNS: 0.0.0.0 · Username: admin · Password: The product unit serial number. If an absolute system reset is performed, all passwords on this device are reset to extron. NOTES: · The computer used for RS232 control should not be one of the host devices connected to any of the input ports. · The LAN IP address can be changed, however, the USBC port IP address is fixed at 203.0.113.22 and cannot be changed. 2 5. Connect the included power supply to the switcher power connector (see figures 2 and 4, A). 6. (Optional) Configure the switcher using PCS as necessary for functions such as autoswitching, front panel lock mode, and emulation (see the SW USB Pro Help File within PCS, available at www.extron.com). 7. Power on the host devices. The switcher is now ready for operation. Front Panel Features AB C D E EXEC AUTO MODE SWITCH CONFIG INPUTS 1 2 Figure 4. Front Panel -- SW2 USB Pro AB C D HOSTS STATUS 1234 DEVICES SW2 USB PRO USB SWITCHER F EXEC AUTO MODE SWITCH 1 CONFIG INPUTS 2 3 STATUS HOSTS 4 1234 DEVICES E F SW4 USB PRO USB SWITCHER Figure 5. Front Panel -- SW4 USB Pro A Exec Mode LED B Auto Switch LED C USB Config port D Input selection buttons and LEDs E Host LEDs F Device LEDs A Exec Mode LED -- Lights when front panel lock mode has been enabled. This can be configured via PCS or SIS commands. B Auto Switch LED -- Lights when autoswitching is enabled. This can be configured via PCS or SIS commands. C USB Config port -- Connect a USB cable (USB Type A to USBC) between a computer or control system and this female USBC port to configure the switcher via SIS commands or PCS, and to update the firmware. This USBC port uses IP over USB communication. The port IP address is 203.0.113.22 at port 22023. D Input selection buttons and LEDs -- Press one of these buttons to select an input to switch to the output. The LED at the right of each button lights when the corresponding input is selected. If autoswitching is in effect, these input selection buttons are disabled, but the LEDs continue to light to indicate the selected input. The input buttons are also used to initiate a system reset and to enable and disable front panel lockout (see the SW USB Pro Series User Guide for more information). E Host status LEDs -- Light if a host is connected to the corresponding host port, whether or not the input is currently selected. F Device status LEDs -- Light when a peripheral device is connected to the corresponding device port and has been enabled by the selected host. 3 SW USB Pro Series · Setup Guide (Continued) For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide on the Extron website. © 2021 Extron -- All rights reserved. www.extron.com All trademarks mentioned are the property of their respective owners. Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876 68353750 Rev. A 12 21 4