GrabCAD Making Additive Manufacturing at Scale Possible
P65Warnings.ca.gov
VAIS Technology - Automotive Electronics Manufacturer- VAIS Technologyvaistech.com/download/15244
User Manual for VAIS TECHNOLOGY models including: AL6-K01, Car Interior LitLED Ambient Lighting, AL6-K01 Car Interior LitLED Ambient Lighting, Car Interior, LitLED Ambient Lighting, Ambient Lighting
Vais Technology AL6-K01 Car interior ambient lighting kit at Crutchfield
File Info : application/pdf, 14 Pages, 5.22MB
DocumentDocumentVAIS TECHNOLOGY
--·
www.vaistech .com
Installation & Operation Manual
LitLED ambient lighting AL6-K01
IIII IIIIIIIIIIIIII III IIIIIIIIIIIIIIII IIll AL6-MAN-001
ill WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Copyright (C) 2003-2022 VAIS Technology Published May 1, 2022
Ambient Lighting Kit
WHAT'S INCLUDED
·e ·
0 ECU - Main Unit
f) Power & Input Harness
0 Mounting Bezel (x6)
C, Output Lens (x6)
BEFORE YOU START
fil WARNING
DO NOT BLOCK THE AIRBAG
Do not mount product or any added equipment where it can obstruct the operation of any safety devices such as the airbag.
DISTRACTION WARNING
Do not let product or any added equipment distract you while you are driving.
fil CAUTION
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS
Cables or wiring that obstruct or get caught on places such as the steering wheel, shift lever, brake pedals, etc. can be extremely hazardous.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST
Moisture or dust may result in product failure.
DISCONNECT THE NEGATIVE BATTERY TERMINAL
Before starting any installation work, you must wait 90 seconds after turning the ignition switch to the LOCK position and disconnecting the negative(-) terminal from the battery. The supplemental restraint system (airbag) is equipped with a backup power source. If installation work is started less than 90 seconds after disconnection of the negative(-) battery terminal, the SRS may deploy. VAIS Technology is not responsible for any vehicle settings lost due to a battery disconnect. Reference owner's manual for vehicle specific details.
Module Connections 2
POWER HARNESS CONNECTIONS Chassis Ground (Black) 12V Constant (Yellow)
Illumination(+) (Blue)
WITH ILLUMINATION ON
-- ov· -':'
LIGHTS WILL RESORTTO LAST COLOR SELECTED
/1\ IF NOT USING DOOR TRIGGER l.D CONNECTTO GROUND
Door Trigger/ Dome Light (Orange) OPTIONAL FEATURE
WITH DOOR TRIGGER ACTIVE ~
0 000
0CJ8HITEQCJ
':'
ENTRY/EXIT LIGHT IS WHITE
SEE PG. 9 FOR SETTINGS
DOOR TRIGGER/ DOME LIGHT(+/-)
Device Default: (12V +) Positive Input
Solid Orange wire is triggered with 12V Signal
For vehicles with(-) Negative Trigger:
Input can be set to(-) Negative.
~
~'fJ.I
Scan QR Code for details.
CONNECTORS AND PORTS
Bluetooth Cover
RearZone Outputs
~ _
f
Power Port
== ==
=~ = ~
0
0
~~
Front Zone Outputs
3 Installation
( INSTALL THE ECU MODULE AND ROUTE THE FIBER OPTIC CABLES )
1 Remove the interior panels where you want to install the lenses.
2 Drill 8mm holes with a step drill bit.
VAIS Recommends Irwin #11102.
Drill at a 90-degree angle to produce an even round hole.
* Th icker panels may require a larger opening
3
Do not bend the fiber optic cables closer than 4 inches from the ECU.
4 inches
4 inches
-·· i
;;
Gently bend cable
Do not over bend
X
Installation 4
( SECURE THE MODULE )
Secure the ECU Module, as shown, use zip t ies and mounting tabs. Make sure to mount the ECU Module with plastic cover facing up.
& Keep plastic cover away from large metal plates.
Mount the module to a structure as shown. DO NOT mount to wiring harnesses, etc.
( INSTALL BEZELS AND LENSES ) 1
Install bezel into the hole that was drilled.
2 Route the fiber optic through the bezel.
3 Install lens on the end of the fiber optic cable.
4 Push the fiber optic cable with the lens into the bezel, pushing in until it clicks into the bezel.
& Do not damage the lens. Guide it directly into
the bezel and do not bend the ends of the lens.
* Repeat these steps for each fiber optic cable.
5 Installation
( DISASSEMBLING THE OUTPUT SIDE ) 1
Use an 8mm socket and wrap the end in protective tape.
& Protective tape is required to protect the bezel
from getting scratched by the 8mm socket.
2 Press 8mm socket firmly against the bezel.
3 Push the fiber optic cable in the direction shown, until the lens comes out.
4 Remove the lens from the fiber optic cable, Pull the cable out of the hole.
App Download & Usage 6
( DOWNLOAD & OPEN THE APP J
LitLED ambient lighting ...... GETITON ,. · Google Play
J ( SELECT THE DEVICE
Select the LitLED device to start using the app.
Troubleshooting If LitLED device does not appear:
Turn vehicle illumination OFF/ON If LitLED app does not connect to the module:
Reboot the phone. If ECU is inactive for over 5 minutes it will go to sleep mode.
To wake up, Open/Close the Door or turn illumination OFF/ON
7 App Download & Usage
( VEHICLE ILLUMINATION )
LitL_.E...D.,
FRONT ZONE
·
Zone Brightness 100%
WHEN VEHICLE'S ILLUMINATION IS OFF
App buttons are Gray, and will not function
Illumination indicator at the bottom of the app screen will be Gray.
REAR ZONE
'r,, Sync )FRON
-$- ·
Zone Color
-
Zone Brightness 100%
Y'(_ To make adJustments vehicle illumination must ¥ beON
'"''
--LitLED
rRONT 70Nf
·
Zone Brightness 100%
~ App will not work while Door Trigger is active.
LD To change Door Trigger settings see Pg. 9
~
Icon will appear when Door Trigger is active.
Illumination Indicator OFF
WHEN VEHICLE'S ILLUMINATION IS ON App buttons will illuminate Blue, and will now function. Illumination icon will light up at the bottom of the screen.
Rr AR ?ONr
C Sync to FRONT
·$· ·
Zone Color
-
Zorie Brightness 100%
Illumination Indicator ON
App Download & Usage 8
( SELECT A ZONE TO CHANGE THE COLOR )
LitLED -¥'"'9
I
FRONT ZONE
I
Sync Front/Rear Zones together.
Q Sync to REAR
-9- ·
ZoneColor
-
Zone Brightness 100%
I
REAR ZONE
I
ON/OFF for Each Zone
C SynctoFRONT
Zone Color Zone Brightness 100%
69dB
( CHOOSE COLOR AND BRIGHTNESS )
FRONT lighting color
Select Color Wheel or Swatches
Select Color Range
- IZone Brightness
-:¢:- -41·
100%
-:+:-
CANCEL
Add White Balance Select Brightness
9 App Download & Usage
----~ LitLED
Demo Mode
Diagnostic Mode
Entry/ Exit Light Setup
C Sync to REAR
Ambient Light Setup
About Zone Color
Zone Brightness 100%
REAR ZONE
C Sync to FRONT
Zone Color Zone Brightness 100%
DIAGNOSTIC MODE
Verify the proper operation of each zone and channel as the app goes through the diagnostic mode.
AL6-K01 unit will cycle through each of the primary colors to verify LED functionality.
/,\ Diagnostic mode will be interrupted if
L.D application switches to background mode.
Diagnostic mode will start over after application returns to foreground mode.
-70dB
Entry/ Exit Light Setup
Dome light/ Door trigger signal pola,ity
,osmve ---,- --
lllumlnatlontlme(dooropen)
60 sec - - - --
lllumlnatlontlme(doorclose)
30 sec - - - --
ENTRY/EXIT LIGHT SETUP
Select Positive or Negative input for dome light Timer for Entry Light when door is open Timer for Entry Light when door is closed
Dimming speed Front zone brightness
Fast - -- -~ Set the Dimming Speed for entry light
7 00 %
Set the Front Zone brightness for entry light
Set the Rear Zone brightness for entry light
Toggle Front Zone (ON/OFF)
Toggle Rear Zone (ON/OFF)
Troubleshooting 1O
Troubleshooting Guide
Symptom
No illumination from interior light by the shifter
Check
1.
Turn headlights ON.
2.
Check and verify harness connection.
LitLED app doesn't
1.
connect to module
2.
No illumination from
1.
interior ambient light, all
2.
sources
3.
4.
One or more (not all) light
1.
sources do not have the
light
2.
3.
Turn headlights ON/OFF. Reboot the phone.
Turn headlights ON. Light is turned off in the app. ECU internal temp 65C (149F) and needs to cool down. i ~will be displayed. Check and verify harness connection
Light is turned off in the app for one or more zones. Check and verify fiber optics cable connection at ECU and Bezel. Make sure fiber optic cable isn't bent more than 30mm radius.
ffi WARNING
DO NOT DISASSEMBLE OR ALTER THE MODULE Doing so may result in an accident, fire, or electric shock.
USE ONLY SPECIFIED ACCESSORY PARTS
Use of other than specified parts may damage product internally.
FOLLOW THE OPERATIONAL AND INSTALLATION MANUALS
YOU SHOULD READ AND FAMILIARIZE YOURSELFTHOROUGHLY WITH THE FOLLOWING INFORMATION PRIOR TO INSTALLING AND USING THIS UNIT. IN ADDITION, YOU MUST CAREFULLY READ AND FOLLOW THE INSTALLATION SCHEMATICS/INSTRUCTIONS FOR THE PRODUCT AND THE VEHICLE IN WHICH IT IS BEING INSTALLED. FAILURETO FOLLOW INSTALLATION INSTRUCTIONS MAY DAMAGE THE PRODUCT AND THE VEHICLE, WILL VOID THE PRODUCT WARRANTY, AND MAY VOID THE VEHICLE WARRANTY.
FCC WARNING
Contains FCC ID:2APD9-RSL10SIP This device complies with Part 1Sof the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by On Semiconductor could void the user'sauthority to operate the equipment.
LIABILITY DISCLAIMER
VAIS Technology can not be held liable for damages or injuries caused by, or resulting from use of this guide. Strictly adhere to all car manufacturer warnings that pertain to the disassembly, maintenance, or servicing of the vehicle and any of its associated part systems. VAIS Technology can not be responsible for discrepancies, or inconsistencies that may occur due to automobile manufacturing changes.
TROUBLESHOOTING
Should this product fail to operate properly, please contact your Dealer or our Customer Service Department at sales@va istech.com
Some visual assets were provided byVecteezy.com and Grabcad.com
-
T EC HN® LO GY
Warranty is available for download: https://www.vaistech.com/download/15244
To request a paper warranty copy please contact us:
VAIS Technology Warranty Department 8811 American Way Unit 125 Englewood, CO 80112 720-733-2348 sales@vaistech.com
111111111111111111 II III IIIIIIIIIIIIIIII IIll AL6-MAN-001
VAIS Technology is not responsible for or liable for any installation cost, property loss, damages whatsoever, including but not limited to, any consequential damages, incidental damages, loss of time, loss of earnings, commercial loss, loss of economic opportunity and the like that may or may not be resulted from the operation of the VAIS Technology product(s). Manufacturer does offer a limited warranty to replace or repair the control module. See Warranty for more information.
VAIS Technology, 8811 American Way #125, Englewood, CO 80112
www.vaistech.com I720-733-2348 Isales@vaistech.com
-
I [ CA~CEl
LitL
ambient lighting
-
"
I 1"\11d , 1 I o1 11..
· App SlOI('
DOWNLOAD THE APP· SELECT DMCE
LitLED 1mbf1nt lighting
0 .,........~
·
,_c:lllol -
t""" ll'"l'!rns IQOI.
0 ,,. '""°"'
-'t( ·
t,an_oCllra;gu<dt,t
-
100'1.
I 'lQ C)lor
·
----.·- * ZoneBrgh1nosa
-
[ CANCEL