User Manual for HOLLYLAND models including: M1, M1 Full Duplex Wireless Intercom System, Full Duplex Wireless Intercom System, Duplex Wireless Intercom System, Wireless Intercom System, Intercom System, System
Amazon.com: Hollyland Solidcom M1 Full Duplex Wireless Intercom System, Multi-Device Cascade Connection, Broadcast Communication for Business Event Concert Sports, 1 Base Station 8 Beltpacks : Electronics
File Info : application/pdf, 28 Pages, 2.43MB
DocumentDocumentSOLIDCOM M1 User Manual V1.1.0 Powered by Hollyland FOREWORD Thank you for purchasing Hollyland Full-Duplex wireless intercom system. Please read this instruction carefully before using the product. Wish you have a pleasant experience. KEY FEATURES · Carrier-Grade Voice Quality, up to 450 Meters Line-of-Sight Usage Distance · 1.9GHz Frequency, Support Frequency Configuration in Different Regions · Automatically Switching between External Omnidirectional Fiberglass Antenna and In-Built Panel Antenna · Full-Duplex Wireless Communicating · The Station Supports up to 8 Beltpacks to Talk at the Same Time. Station, App and Webserver Configuration Upgrade supported · Beltpack Supports Simultaneous Calls in 3 Groups · The Station Supports Cascading or Connecting with the 2/4 Wire Audio Systems · Station's Power could be Supplied by POE Cascading or NP-F Type Batteries · In-Built Lithium Battery for the Beltpacks, Usage for over 6 hours · Portable Storage Charging Base, Easy to Carry · 10 Levels Volume. Different Needs of Scenes Satisfied EN-01 PACKING LIST EN-02 PACKING LIST 8-BELTPACK PACKAGE Station x1 Beltpack x8 Charging Base x1 High Gain Omnidirectional Antenna x2 LEMO Single-Ear Headset x8 POE Adapter x1 RJ45 to XLR Transferring Cable (5 meters) x1 USB-Type-A to Type-C Transferring Cable x1 4Pin XLR Adapter x1 Battery for Beltpacks x16 3/8 Installing Accessory x1 User Guide x1 4-BELTPACK PACKAGE Station x1 Beltpack x4 Charging Base x1 High Gain Omnidirectional Antenna x2 LEMO Single-Ear Headset x4 POE Adapter x1 RJ45 to XLR Transferring Cable (5 meters) x1 USB-Type-A to Type-C Transferring Cable x1 4Pin XLR Adapter x1 Battery for Beltpacks x8 3/8 Installing Accessory x1 User Guide x1 * The exact quantity may vary on products configuration. Please take the actual quantity as standard. EN-03 PRODUCT INTERFACES 3.5mm Headset Interface Interface Definition: MGRL Microphone Independence: 600 Speaker Independence: 32 LEMO Headset Interface PIN1: GND PIN2: GND PIN3: SPK PIN4: SPK + PIN5: MIC + PIN6: MIC PIN7: NULL PIN8: LED EN-04 PRODUCT INTERFACES 4-Wire Interface Input Independence: 10K PIN1: NULL PIN2: NULL PIN3: AUDIO OUT+ PIN4: AUDIO IN+ PIN5: AUDIO INPIN6: AUDIO OUTPIN7: GND PIN8: GND 2-Wire Interface PIN1: GND PIN2: POWER PIN3: AUDIO POE/PWR Interface PIN1: -POWER PIN2: -POWER PIN3: +POWER PIN4: +POWER PIN5: +POWER PIN6: +POWER PIN7: -POWER PIN8: -POWER EN-05 PRODUCT INTERFACES EN-06 PRODUCT INTERFACES STATION Antenna Interface Up Key Left Key Menu/Confirm Key (Long Press to the Menu/ Short Press to Select) Right Key Down Key Power Button 3/8 Screw Hole Interface for NP-F Type Battery Power Supply Interface 4-Wire Audio Input-Output Interface (RJ45 Interface) USB Interface 3/8 Screw Hole 2-Wire Audio Input-Output Interface POE Interface EN-07 PRODUCT INTERFACES EN-08 PRODUCT INTERFACES BELTPACK Antenna Mute/Talk Switch Key, Press Down for Talk, Up for Mute Battery Compartment Switcher USB Type-C Interface Left Key/A Group Key (The beltpack is not grouped when the indicator light is off, The beltpack is joined Group A but unable to talk or listen when the Indicator light is white, The beltpack is able to talk and listen in Group A when the Indicator light is orange) Menu/ B Group Key (Long press to enter Menu/The beltpack is not grouped when the indicator light is off, The beltpack is joined Group B but unable to talk or listen when the Indicator light is white, The beltpack is able to talk and listen in Group B when the Indicator light is orange) Right Key/C Group Key (The beltpack is not grouped when the indicator light is off, The beltpack is joined Group C but unable to talk or listen when the Indicator light is white, The beltpack is able to talk and listen in Group C when the Indicator light is orange) Volume+ Button Volume- Button Back Clip Power Switcher Charging Contact LEMO Headset Interface 3.5mm Headset Interface EN-09 DISPLAY INTRODUCTION STATION MAIN DISPLAY INTRODUCTION Current Battery Voltage of Station Current Status of Beltpack TALK: The beltpack is able to talk while listening. MUTE: The beltpack is able to listen but unable to talk. LOST: The beltpack is disconnected from the station. LINK: The beltpack is linking to the station. Beltpack Number Current Battery Usage of Beltpack Current Signal Strength of Beltpack Low Battery Display of Beltpack EN-10 DISPLAY INTRODUCTION BELTPACK MAIN DISPLAY Current Signal Strength Charging Notice Current Battery Usage Beltpack Number Current Status TALK: Able to Talk while Listening MUTE: Able to Listen but unable to Talk LOST: Disconnected from the Station LINK: Linking to the Station EN-11 GUIDE EN-12 GUIDE STATION MENU INTRODUCTION Long press Menu/Confirm Key for 3 Seconds to enter the Menu, following is the menu function's Introduction. Select "Network" to Switch WiFi on/off, See the WiFi Password and IP Address. Select "Master and Slave" to Set the Station as Master Device/Slave Device. 2.1 If there's only one kit of devices, the station needs to be set as Master Device; When two or more kits are cascaded, the station can be set as Master Device/ Slave Device. 2.2 When the station is set as Master Device, The beltpack number will automatically switch to 1-8; When the station is set as Slave Device, The beltpack number will automatically switch to 9-16. 2.3 This function can only be used when two kits of devices cascaded by Ethernet interface. The Station needs to be set as Master Device when only one kit of devices used. Select "4 Wire" Entering 4 Wire Audio Settings. 3.1 Enter the Menu to adjust 4 Wire audio system input/output gain. 3.2 Switch sequence of line. Select "Language" to Switch Language to Chinese or English. Select "Group" Entering Group Settings. 5.1 One Group: To group all the beltpacks, 2 Wire and 4 Wire audio devices to Group A. The indicator light of Group A Key on the beltpacks will shine 5.2 Two Groups: To group number 1-4 beltpacks, 2 Wire and 4 Wire audio devices to Group A, number 5-8 beltpacks to Group B, The indicator light of corresponding groups on the beltpacks will shine. 5.3 Customize: Able to group beltpacks, 2 Wire or 4 Wire audio devices though Direction Keys and Confirm Key. After setting the corresponding indicator light of the beltpack will shine; 5.4 Defaults: Able to group all beltpacks, 2 Wire and 4 Wire to Group A, After setting the indicator light of Group A will shine. EN-13 GUIDE Select "2 Wire" Entering 2 Wire Settings. 6.1 After connected to 2 Wire devices, set the corresponding wire length compensation and terminal resistor of the station. Power on the 2 Wire devices. Meanwhile the microphone of 2 Wire devices needs to be turned off or disconnected to make sure there's no other audio transmitting in the 2 Wire connection. Otherwise, the Auto Null will be affected. Select "Auto Null", the station will complete the Auto Null operation of 2 Wire Devices; 6.2 Select "Cable Compen", confirm the bus length of the same parallel 2 Wire Interface. Select the corresponding compensation selection according to the bus length; 6.3 Select "Terminal Res", confirm whether the 2 Wire Device connected by the 2 Wire interface has terminal resistor. The terminal resistor needs to switch to Off if the 2 Wire Device has terminal resistor. The terminal resistor needs to switch to On if the 2 Wire Device doesn't have terminal resistor; 6.4 Select "Input Gain" to enter input gain adjust menu, Select the corresponding level to increase or decrease the corresponding value of the input signal; 6.5 Select "Output Gain" to enter output gain adjust menu, Select the corresponding level to increase or decrease the corresponding value of the output signal. Select "Reset" to Reset all the Adjusted Info of Station to Defaults. Select "Info" to Check the Information of the Station. EN-14 GUIDE BELTPACK MENU INTRODUCTION Long press Menu Key for 3 seconds to enter the menu, Following is the introduction of each function. Connect the Beltpack to the Station by USB-A to TypeC Cable, Select "Pair", the Beltpack can Paired with Station. Select the usable number from 1 to 8 to confirm paring, Both the station and the beltpack's screens will display "Pairing...". Disconnect the beltpack from station when the screens Display "Pairing Successful". Select "SideTone" to set the SideTone Output Volume. SideTone off when it is at Level 0, The SideTone will Increase from Level 1 to 3. Select "Language" to Switch Language to Chinese or English. Select "Reset" to Reset all the Adjusted Info of Beltpack to Defaults. Select "Info" to Check the Information of the Beltpack. Select "Exit" Exit to the Main Menu. Double Click the A/B/C Button on the Beltpack to Enter or Exit the Group. EN-15 GUIDE SET THE STATION BY WEB SERVER Power on the station. Connect POE or PWR Interface to the Ethernet interface of computer by Ethernet Cable. Configure the network segment of the computer to be consistent with the station, Then open the browser on the computer and enter the following address (Check the corresponding address through the Network Menu of the station). Master Device: 192.168.218.10 Slave Device: 192.168.218.11 Log in and enter Web page (Account: admin Default passcode: 12345678) can upgrade the Station, group the beltpacks and adjust the status of beltpacks. EN-16 GUIDE SET THE STATION BY APP 1. "Solidcom" App Download 2. Connecting Methods: Turn on the WiFi of station. Find the WiFi start with "HLD" on the phone and connect. Open the Solidcom App to connect. (Turn the WiFi on and check the corresponding Wifi name and password through the Network Menu of the station) EN-17 PRODUCT INSTALLATION Station Installation 1. Install the antenna according to the picture. 2. Connect the power adapter, or install NP-F type battery. 3. Press the power button to power on. EN-18 PRODUCT INSTALLATION EN-19 PRODUCT INSTALLATION Beltpack Installation 1. Open the battery compartment, insert the battery in the direction marked on the battery. 2. Switch the power switcher on to power on. 3. After the beltpack status changes from "LOST" to "TALK", You can Talk Now. Press the top button will change to "MUTE". The beltpack is able to listen but unable to talk. The status will be changed when the button is pressed again. 4. The beltpack supports both 3.5mm and LEMO headset to connect. 5. When connect to other Intercom Systems though 4 Wire or 2 Wire Audio Interfaces, Users can adjust input and output gain in the Menu of station to balance the entire gain of the Intercom System. 6. The battery will enter the dormant state after being placed for a period of time. It is recommended to fully charge and discharge the beltpack for the first three times. Re-Pair The beltpack number may be lost due to wrong operation or other reasons. You can connect the beltpack to the station with a USB to Type-C cable. Enters "Pair" Menu of the beltpack and select an optional number for pairing. Both the station and the beltpack's screens will display "Pairing...". Disconnect the beltpack from the station when the screens display "Pairing Successful". EN-20 PRODUCT INSTALLATION Cascade Two Sets of Devices 1. Through the dedicated-level Ethernet cable in the accessories, Two Sets of stations can be cascaded, and the number of beltpacks can be expanded up to 16 Beltpacks. When Cascading, One of the Master Device beeds to set as Slave Device. If set Master Device to Slave Device when used alone, the beltpack will not be able to talk and the device needs to be reset as Master Device. 2. When cascading, the beltpack number of the Slave Device will automatically change to 9-16. 3. When the Master Device uses the POE adapter to supply power, the POE adapter needs to connect to the Power Interface of the Master Station. When cascading, the Ethernet cable needs to connect to the POE Interface of the Master Device and the Power Interface of the Slave Device, which can realize the power supply to the Slave Device without Battery. It is available when the POE Adapter is not used but NP-F Type Battery for power supply. EN-21 PRODUCT INSTALLATION Cascade Other Wired or Wireless Intercom System CASCADE WITH SYSCOM 450T. 4 WIRE RJ45 to Dual XLR Audio Cable CASCADE WITH MARS T1000. Audio IN/OUT 4 WIRE Standard Ethernet Cable Rj45 Interface EN-22 PRODUCT INSTALLATION CASCADE WITH OTHER WIRED INTERCOM SYSTEM. 2 WIRE XLR Audio Interface Standard XLR Audio Cable EN-23 PARAMETERS Interfaces Power Supply Frequency Response Signal-to-Noise Ratio Distortion Use Range Frequency Band Modulation Mode Transmit Power Receiving Sensitivity Frequency Bandwidth Power Consumption Dimension Weight Working Temperature Station Beltpack POE Interface (RJ45) Power Supply Interface (RJ45) 4 Wire Audio Interface USB Interface 2 Wire Audio Interface 3.5mm Headset Interface LEMO Headset Interface USB-Type-C Interface POE Power Supply NP-F Type Battery 1500mAh Lithium Polymer Battery 200Hz to 7KHz 200Hz to 7KHz >50dB >50dB <1% <1% 450 Meters Line-of-Sight Usage 450 Meters Line-of-Sight Usage 1.9GHz 1.9GHz GFSK GFSK Maximum 21dBm Maximum 21dBm -93dBm -93dBm 1.728MHz 1.728MHz <3W <0.6W (L*W*H): 255*180.4*48.5mm (L*W*H): 105*65*22.4mm About 1560g About 200g 0 ~ +45°C (Working Status) -20 ~ +60°C (Stock Status) 0 ~ +45°C (Working Status) -20 ~ +60°C (Stock Status) SAFETY PRECAUTIONS Do not place the beltpacks in the accessories or inside of Heating Equipment, Cooking equipment, High-Pressure Containers, etc. (Such as Microwave Ovens, Induction Cookers, Electric Ovens, Electric Heaters, Pressure Cookers, Water Heaters, Gas Stoves, etc.) to prevent the battery from overheating and exploding. The Charger, data cable and battery of the original matching model must be used. Using chargers, data Cables, and batteries that are not certified by the manufacturer or of non-matching models may cause Electric Shock, Fire, Explosion, or Other Dangers. EN-24 SUPPORT If encounter any problems in using the product or need any help, please follow these ways to get more technical support: Hollyland User Group HollylandTech HollylandTech HollylandTech support@hollyland-tech.com www.hollyland-tech.com EN-25 WIRELESS INTERCOM SYSTEM Hollyland User Group HollylandTech HollylandTech HollylandTech support@hollyland-tech.com www.hollyland-tech.com Shenzhen Hollyland Technology Co., Ltd. 8F, 5D Building, Skyworth Innovation Valley, Tangtou, Shiyan, Baoan District Shenzhen, China.