Product Description
Thank you for purchasing Sonance Mariner weather-resistant speakers. When properly installed, these speakers will provide many years of outdoor entertainment pleasure. Please read this manual thoroughly before beginning installation.
This manual applies to the following models: Mariner 54, Mariner 54 SST, Mariner 56, Mariner 64, Mariner 64 SST, Mariner 66, and Mariner 86.
Box & Contents
Sonance Mariner 54, 56, 64, 66, and 86 (2-Way Speaker Boxes) contain:
- (2) Speakers
- (2) Speaker Grilles
- (2) FastMount® Brackets
- (2) Wiring Terminal Covers
Sonance Mariner 54 SST, and 64 SST (Single Stereo Speaker Boxes) contain:
- (1) Speaker
- (1) Speaker Grille
- (1) FastMount® Bracket
- (1) Wiring Terminal Cover
Speaker Placement
Mariner speakers are highly weather-resistant and designed for excellent performance in outdoor conditions. The Mariner FastMount bracket system facilitates mounting in various positions and locations, as illustrated in Figure 1.
Figure 1: Speaker Placement illustrates four mounting positions: against a wall (flush), under an eave, in a corner, and on a pole.
For optimal performance, place speakers at ear level, facing the listeners. If mounting above or below ear level, pivot the speakers to direct sound towards the listeners. Speakers can be oriented horizontally or vertically without affecting sound quality.
Types of Wire
When installing Sonance Mariner Outdoor Speakers, careful consideration must be given to speaker placement and the appropriate wire gauge. Refer to the wiring chart (Figure 2) to determine the correct wire size based on the distance between the amplifier/receiver and the speakers.
Figure 2: Wire Gauge Chart is a table showing recommended wire gauge based on distance for optimal performance.
| Wire Gauge | Distance |
|---|---|
| 18 Gauge | Up to 100 feet (30 meters) |
| 16 Gauge | Up to 150 feet (45 meters) |
| 14 Gauge | Up to 250 feet (80 meters) |
| 12 Gauge | Up to 400 feet (122 meters) |
| 10 Gauge | Up to 650 feet (198 meters) |
Connecting and Assembling the Speakers
WARNING: Ensure the amplifier's power is OFF before completing any connections. For added safety, unplug the amplifier from the wall outlet to prevent accidental turn-on.
- In most cases, FastMount brackets can be attached directly to the mounting surface. Run speaker wires from the amplifier to the speaker locations and through the bracket holes. (See Figure 3).
- Figure 3: Pass Wire Through Hole shows speaker wire being fed through a mounting bracket hole.
- Note: To enhance water resistance and ease of installation, speaker wire terminals are located on the front panel. Ensure sufficient wire is available to feed through the enclosure's tunnel and connect to the front terminals.
- Attach the FastMount brackets to the mounting surface using appropriate hardware (not included) for the surface type. (See Figure 4).
- Figure 4: Attach Bracket depicts a FastMount bracket being attached to a surface.
- For corner installations, attach the bracket using hardware through the slots in the angled corners. (See Figure 5).
- Figure 5: Corner Mounting shows how to attach a bracket using slots for corner installations.
- For pole mounting, attach the FastMount brackets to the pole using 2.5" U-bolts (not included). (See Figure 6).
- Figure 6: Attaching Bracket to a Pole illustrates using U-bolts to attach a bracket to a pole.
- Feed speaker wires from the bracket into the wire entry grommet on the speaker's back, through the wire tunnel, and out the front panel opening. (See Figure 7).
- Figure 7: Wire Entry Grommet shows the speaker wire entering the speaker enclosure through a grommet at the back.
- The grommet creates a water-resistant seal around the speaker wire. Ensure enough wire slack is left to allow the speaker to pivot on the bracket.
- Slide the speaker onto the bracket and firmly snap it into place. Pull enough wire through the front to connect to the terminals. (See Figure 8).
- Figure 8: Attach Speakers to Brackets depicts sliding the speaker onto the mounted bracket.
- Note: Ensure the bracket clips snap completely into place to prevent any blockage within the speaker perimeter where the grille will be inserted.
- Connect the speaker wires to the speaker's terminals:
- Strip approximately 0.5" (12mm) of insulation from each conductor and twist the strands together or tin with solder.
- Press down on the tops of the connectors to open them.
- Insert the wires into the connector holes. (See Figure 9).
- Release the connectors.
- Figure 9: Connection Terminals shows the speaker's front panel terminals and how to connect wires.
- The binding post connectors accept wire up to 14 gauge. Double-check all wire connections (amplifier '+' to speaker '+'; amplifier '-' to speaker '-') are correct.
- IMPORTANT: Prevent any stray '+' and '-' wires from touching each other, as this can cause a short circuit and damage the amplifier.
- Fit the wiring connector cover into the recess on the speaker's front panel. The cover should fit snugly but can be removed for disconnection. (See Figure 10).
- Figure 10: Attach the Connector Cover illustrates fitting the wiring connector cover.
- Fit the grille onto the speaker by aligning its edges with the speaker face perimeter groove and pressing firmly until it is snugly in place. (See Figure 11).
- Figure 11: Attach the Grille shows how to align and press the grille into place.
Omnimount Compatibility: All Sonance Mariner speakers are compatible with Omnimount Stainless Steel 15.0 C and 15.0 W Series speaker brackets. For more information, contact your Sonance authorized dealer or visit www.omnimount.com.
Removing the Speaker
To remove the speaker from the FastMount bracket, use the provided grille pick to gently pull the grille at each corner until it is freed from the speaker face grooves. Then, press outward on the top and bottom tabs of the speaker face to release the bracket clips. While pressing the tabs, gently pull the speaker towards you until it detaches from the bracket.
Pivoting the Speaker
You can rotate the speaker in the bracket to direct sound towards the listeners.
- Unlock the slide locks on the speaker pivots by moving them towards the rear of the speaker. (See Figure 12).
- Rotate the speakers to the desired position.
- Lock the slide locks by moving them towards the front of the speaker.
Figure 12: Lock and Unlock Slide Locks to Pivot Speaker illustrates the sliding mechanism for pivoting the speaker, showing the unlock (rearward) and lock (forward) positions.
Painting the Speaker and Grille
All Mariner speakers feature a durable polypropylene enclosure that can be painted. Sonance recommends using a weather-resistant outdoor paint and a spray gun.
- If the speaker is already installed, remove the grille.
- To protect the speaker driver units during painting, place the grille on cardboard, trace its outline, and cut slightly inside the line. Fit this "paint plug" into the speaker's baffle, being careful not to damage driver components.
- Paint the speaker according to the paint manufacturer's instructions. Remove the paint plug after the paint has thoroughly dried.
- Paint the grille separately using very thin paint (5:1 thinner:paint ratio). Avoid clogging the grille holes with excess paint.
- After the paint has thoroughly dried, re-attach the grille to the speaker.
Specifications
| Model | Tweeter | Woofer | Frequency Response | Impedance | Power Handling | Sensitivity | Environmental | Environment Temp | Dimensions (WxHxD) | Grille | Shipping Weight |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Mariner 54 | 1" (25mm) cloth dome, Ferrofluid cooled, in acoustic back chamber | 5.25" (130mm) textured polypropylene cone with a Santoprene surround | 65Hz - 20kHz ±3dB | 8 ohms nominal; 6 ohms minimum | 5W min; 60W max | 87dB SPL (2.83V/1m) | Conforms to Mil Spec 810 for humidity, salt spray, temperature and UV, IP-66 waterproof rating | -13° - 149°F (-25°C - 65°C) | 6.36" x 10.08" x 5.68" (162mm x 256mm x 144mm) | Perforated aluminum | 12 lbs. (5.5kg) pair |
| Mariner 54 SST | Two 1" (25mm) cloth dome, Ferrofluid cooled, in acoustic back chamber | 5.25" (130mm) textured polypropylene cone with a Santoprene surround, dual voice coil | 65Hz - 20kHz ±3dB | 8 ohms nominal; 6 ohms minimum | 5W min; 60W max | 87dB SPL (2.83V/1m) | Conforms to Mil Spec 810 for humidity, salt spray, temperature and UV, IP-66 waterproof rating | -13° - 149°F (-25°C - 65°C) | 6.36" x 10.08" x 5.68" (162mm x 256mm x 144mm) | Perforated aluminum | 6 lbs. (2.8kg) each |
| Mariner 56 | 1" (25mm) powder-coated aluminum dome, Ferrofluid cooled, in acoustic back chamber | 5.25" (130mm) Kevlar/Nomex laminated cone with a Santoprene surround | 60Hz - 20kHz ±3dB | 8 ohms nominal; 6 ohms minimum | 5W min; 70W max | 88dB SPL (2.83V/1m) | Conforms to Mil Spec 810 for humidity, salt spray, temperature and UV, IP-66 waterproof rating | -13° - 149°F (-25°C - 65°C) | 6.36" x 10.08" x 5.68" (162mm x 256mm x 144mm) | Perforated aluminum | 13 lbs. (6kg) pair |
| Mariner 64 | 1" (25mm) cloth dome, Ferrofluid cooled, in acoustic back chamber | 6.5" (165mm) textured polypropylene cone with a Santoprene surround | 55Hz - 20kHz ±3dB | 8 ohms nominal; 6 ohms minimum | 5W min; 80W max | 89dB SPL (2.83V/1m) | Conforms to Mil Spec 810 for humidity, salt spray, temperature and UV, IP-66 waterproof rating | -13° - 149°F (-25°C - 65°C) | 7.51" x 12.14" x 6.86" (191mm x 308mm x 174mm) | Perforated aluminum | 14 lbs. (6.4kg) pair |
| Mariner 64 SST | Two 1" (25mm) cloth dome, Ferrofluid cooled, in acoustic back chamber | 6.5" (165mm) textured polypropylene cone with a Santoprene surround, dual voice coil | 55Hz - 20kHz ±3dB | 8 ohms nominal; 6 ohms minimum | 5W min; 80W max | 89dB SPL (2.83V/1m) | Conforms to Mil Spec 810 for humidity, salt spray, temperature and UV, IP-66 waterproof rating | -13° - 149°F (-25°C - 65°C) | 7.51" x 12.14" x 6.86" (191mm x 308mm x 174mm) | Perforated aluminum | 7 lbs. (3.2kg) each |
| Mariner 66 | 1" (25mm) powder-coated aluminum dome, Ferrofluid cooled, in acoustic back chamber | 6.5" (165mm) Kevlar/Nomex laminated cone with a Santoprene surround | 50Hz - 20kHz ±3dB | 8 ohms nominal; 6 ohms minimum | 5W min; 100W max | 90dB SPL (2.83V/1m) | Conforms to Mil Spec 810 for humidity, salt spray, temperature and UV, IP-66 waterproof rating | -13° - 149°F (-25°C - 65°C) | 7.51" x 12.14" x 6.86" (191mm x 308mm x 174mm) | Perforated aluminum | 17 lbs. (7.7kg) pair |
| Mariner 86 | 1" (25mm) powder-coated aluminum dome, Ferrofluid cooled, in acoustic back chamber | 8" (203mm) Kevlar/Nomex laminated cone with a Santoprene surround | 45Hz - 20kHz ±3dB | 8 ohms nominal; 6 ohms minimum | 5W min; 125W max | 91dB SPL (2.83V/1m) | Conforms to Mil Spec 810 for humidity, salt spray, temperature and UV, IP-66 waterproof rating | -13° - 149°F (-25°C - 65°C) | 9.01" x 14.02" x 8.58" (229mm x 356mm x 218mm) | Perforated aluminum | 20lbs. (9kg) pair |
Limited Five (5) Year Warranty
Sonance warrants this product to the original end-user purchaser, when bought from an authorized Sonance Dealer/Distributor, to be free from defective workmanship and materials for the product's life, except for the grille, which is warranted for five (5) years. Sonance will, at its option and expense, repair or replace the product with a new or remanufactured unit or a reasonable equivalent.
Exclusions: To the extent permitted by law, this warranty is exclusive and in lieu of all other warranties, express or implied, including implied warranties of merchantability, fitness for use, and fitness for a particular purpose. Sonance is not liable for consequential, incidental, economic, property, or personal injury damages arising from the product or any warranty breach. This warranty grants specific legal rights, which may vary by state.
Additional Limitations: The warranty is non-transferable, applies only to the initial installation, and does not cover installation of repaired/replaced products, damage to associated equipment, or issues arising from accident, disaster, negligence, improper installation, misuse (e.g., overdriving, extreme temperatures/humidity), or unauthorized service.
Obtaining Authorized Service: To qualify for warranty service, contact your authorized Sonance Dealer/Installer or Sonance Customer Service at (949) 492-7777. Obtain a return merchandise number (RMA) and ship the product prepaid with proof of purchase.
Contact Information
©2018 Sonance. All rights reserved. Sonance and FastMount are registered trademarks of Dana Innovations. Features and specifications are subject to change without notice. For the latest information, visit www.sonance.com.
Sonance
991 Calle Amanecer
San Clemente, CA 92673 USA
(949) 492-7777 • FAX: (949) 361-5151
www.sonance.com
