Owner's Manual for WAC LIGHTING models including: WB-IA62C1, WB-IA62C1 BLE Module, BLE Module, Module
WAC LIGHTING CO WAC000005 BLE module 2APNFWAC000005 2APNFWAC000005 wac000005
File Info : application/pdf, 18 Pages, 1.37MB
DocumentDocumentWAC Lighting Co ModuleWB-IA62C1 Product Specification Product Description Module NO Customer Name Customer PN BLE Module WB-IA62C1 Wrote By Xiekehuang 2024-05-28 Check LIDAYU 2024-05-28 approve MAXZHANG 2024-05-28 Customer acknowledgement column R&D Department Engineering Department Quality Department 1 WAC Lighting Co ModuleWB-IA62C1 Catalog Catalog...... ...............................................................................................................................................2 1 Basic Information ...................................................................................................................................3 1.1 Module type ................................................................................................................................................... .3 1.2 Revision History ............................................................................................................................................... 3 2 General Description............................................................................................................................4 2.1 Block Diagram................................................................................................................................................. 4 2.2 Features .......................................................................................................................................................... 5 3Characteristic Description....................................................................................................................6 3.1 Hardware features .......................................................................................................................................... 6 3.2 Electrical features ........................................................................................................................................... 6 3.3 Environmental Requirement ........................................................................................................................... 7 4Mechanical Specifications .................................................................................................................10 5 PCB layout Attention ........................................................................................................................12 6 Reflow - furnace temperature curve..................................................................................................13 7Patch BT modules installed before the notice...................................................................................14 8 Package ...........................................................................................................................................15 2 WAC Lighting Co 1 Basic Information ModuleWB-IA62C1 1.1 Module type Module WB-IA62C1 Size 12mm*18mm*2.2mm±0.2mm Process types SMD Mark 1.2 Revision History Date Version 2024-05-28 1.0 Authorize d MaxZhang Remarks First release 3 WAC Lighting Co 2General Description ModuleWB-IA62C1 WB-IA62C1 is a 12mmx18mm size module . It is based on Realtek RTL8762CMF chip. WB-IA62C1 is a ultra-low-power system on-modele solutions for Bluetooth 5 low energy applications that combine the excellent performance of a leading RF transceiver with a low-power ARM Cortex-M4F and rich powerful supporting features and peripherals. The embedded ARM Cortex-M4F 32-bit CPU features a 16-bit instruction set with 32-bit extensions that delivers high-density code with a small memory footprint. By using a single-cycle 32-bit multiplier,a 3-stage pipeline,and a Nested Vector Interrupt Controller,the ARMCortex-M4F makes program execution simpe and hihly efficient.The RTL8762c memory architectrue includes ROM,160kByte RAM and 8MByte Flash Address Space. 2.1 Block Diagram 4 WAC Lighting Co ModuleWB-IA62C1 2.2 Features General Ultra-low power consumption with intelligent PMU Supports Bluetooth 5 core specification Supports 2Mbps LE LE advertising Extensions LE Long Range Channel Selection #2 High Duty Cycle Non-Connectable Adv Integrated MCU to execute Bluetooth protocol stack Supports multiple level Low Energy states Supports LE L2CAP Connection Oriented Channel Support Supports LE low duty directed advertising Supports LE data length extension feature Supports OTA (Over-the-Air) programming mechanism for firmware upgrade Generic Applications for GAP Central, Peripheral, Observer and Broadcaster Roles The module has a 1db Bluetooth 2.4G Antenna built-in. Interface Timers x 8 I2C x 2 PWM x 8 UART x 2 GPIO x 24 I2S/PCM interface for external audio codec Features ARM Cortex-M4F with floating-point unit (Maximum 40MHz) Serial flash controller with 16kB 4-way cache Total 160kB SRAM 160kB SRAM 4Kbits eFUSE for manufacturer use Embedded 4Mbits flash Max TX power:8dBm RX sensitivity:-97dBm BLE(min) Operating Condition Operating voltage: 3.3V IO voltage:3.3V /1.8V Temperature range: -40°C to +85°C Applications: MESH LED 5 WAC Lighting Co 3Characteristic Description 3.1 Hardware features Module Major Chipset WB-IA62C1 RTL8762CMF Standards Bluetooth 5 Operating Voltage Operating voltage: 3.3V IO voltage:3.3V /1.8V 3.2 Electrical features 3.2.1 power on timing is shown in the figures below ModuleWB-IA62C1 6 WAC Lighting Co 3.2.2 Low Power Mode ModuleWB-IA62C1 3.2.3 Active Mode Power Consumption 3.2.4 I2C Timing Characteristics 7 WAC Lighting Co 3.2.5 UART Characteristics ModuleWB-IA62C1 3.2.6 AUX ADC 8 WAC Lighting Co 3.3 Environmental Requirement ModuleWB-IA62C1 Input power ripple VDD Power input requirements Operating Temperature 50mV 3.3V/0.3A -40 ~ +85 9 WAC Lighting Co 4Mechanical Specifications 4.1 Size (unit:mm) 12*18*2.2mm ±0.2 ModuleWB-IA62C1 4.2 Pin definition and description Pin Number Name 1 GND 2 P2_3 3 P2_4 4 P2_5 5 P2_6 6 P2_7 Description GND GPIO;With wakeup function;AUXADC input 3. GPIO;With wakeup function;AUXADC input 4. GPIO;With wakeup function;AUXADC input 5. GPIO;With wakeup function;AUXADC input 6. GPIO;With wakeup function;AUXADC input 7. 10 WAC Lighting Co 7 P0_5 8 P0_6 9 P4_0 10 GND 11 P0_1 12 VDDIO 13 P4_2 14 P4_1 15 P4_3 16 P0_4 P0_3 17 18 P0_2 19 32.768KHz_out 20 32.768KHz_in 21 GND 22 P0_0 23 GND 24 P5_0 25 P1_0 26 GND 27 P2_2 28 P1_1 29 P3_2 30 VCC 31 P3_3 32 P3_0 33 P3_1 34 BT_RST 35 GND ModuleWB-IA62C1 GPIO;With wakeup function GPIO;With wakeup function GPIO;With wakeup function GND GPIO;With wakeup function 1.8V or 3.3V GPIO;With wakeup function GPIO;With wakeup function GPIO;With wakeup function GPIO;With wakeup function GPIO;With wakeup function; Log_UART_TX; Pull-down to bypass executing program code in flash GPIO;With wakeup function 32.768KHz crystal input or external clock output(Optional); 32.768KHz crystal input or external clock input(Optional); GND GPIO;With wakeup function GND GPIO;With wakeup function GPIO;With wakeup function;SWDIO (default). GND GPIO;With wakeup function;AUXADC input2. GPIO;With wakeup function;SWDCLK (default). GPIO;With wakeup function 3.3V/0.3A Main Power input GPIO;With wakeup function GPIO;With wakeup function;HCI_UART_TX (default). GPIO;With wakeup function;HCI_UART_RX (default). Hardware Reset; If not use,Please NC GND 11 WAC Lighting Co 5PCB layout Attention ModuleWB-IA62C1 It is recommended that the distance between the module antenna part and other metal parts should be at least over 15mm or above. User PCB board in the antenna area do not line or even copper, so as not to affect the antenna performance ( 15mm PCB ). WAC Lighting Co 6Reflow - furnace temperature curve ModuleWB-IA62C1 WAC Lighting Co ModuleWB-IA62C1 7Patch BT modules installed before the notice B T module installed note: 1. Please press 1 : 1 and then expand outward proportion to 0.7 mm, 0.12 mm thickness When open a stencil. 2 . Take and use the WIFI module, please insure the electrostatic protective measures. 3 . Reflow soldering temperature should be according to the customer the main size of the products, such as the temperature set at 250 + 5 for the MID motherboard. About the module packaging, storage and use of matters needing attention are as follows: 1. The module of the reel and storage life of vacuum packing: 1 ) . Shelf life: 8 months, storage environment conditions: temperature in: < 40, relative humidity: < 90% r.h. 2. The module vacuum packing once opened, time limit of the assembly: Card: 1) check the humidity display value should be less than 30% (in blue), such as: 30% ~ 40% (pink), or greater than 40% (red) the module have been moisture absorption. 2) factory environmental temperature humidity control: -30 , 60% r.h.. 3) Once opened, the workshop the preservation of life for 168 hours. 3. Once opened, such as when not used up within 168 hours: 1) The module must be again to remove the module moisture absorption. 2) The baking temperature: 125 , 8 hours. 3). After baking, put the right amount of desiccant to seal packages WAC Lighting Co 8Package 8.1 Reel A roll of 1500pcs ModuleWB-IA62C1 WAC Lighting Co 8.2 MSL Level / Storage Condition ModuleWB-IA62C1 NOTE : Accumulated baking time should not exceed 96hrs WAC Lighting Co FCC Warning ModuleWB-IA62C1 Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules FCC Part 15.247 2.3 Specific operational use conditions This transmitter/module and its antenna(s) must not be co-located or operating in conjunction with any transmitter. This information also extends to the host manufacturer's instruction manual. 2.4 Limited module procedures Not applicable 2.5 Trace antenna designs Explanation: Yes, The module with trace antenna designs, and This manual has been shown the layout of trace design,, antenna, connectors, and isolation requirements. 2.6 RF exposure considerations This equipment complies with FCC, RF radiation exposure limits set forth for an uncontrolled environment 2.7 Antennas PCB Antenna; 0.9dBi; 2.402 GHz~2.480GHZ Rod Antenna ;2.87dBi; 2.402 GHz~2.480GHZ 2.8 Label and compliance information The end product must carry a physical label or shall use e-labeling followed KDB784748D01 and KDB 784748 stating "Contains Transmitter Module FCC ID: 2APNFWAC000005. 2.9 Information on test modes and additional testing requirements For more information on testing, please contact the manufacturer. 2.10 Additional testing, Part 15 Subpart B disclaimer The modular transmitter is FCC authorized for the specific rule parts (FCC Part 15.247) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testina with the modular transmitter installed when contains diaital circuity. FCC StatementsWAC Lighting Co ModuleWB-IA62C1 (OEM) lntegrator has to assure compliance of the entire end-product incl. the integrated RF Module. For 15 B ($15.107 and if applicable $15.109) compliance, the host manufacturer is required to show compliance with 15 while the module is installed and operating. Furthermore the module should be transmitting and the evaluation should confirm that the module's intentional emissions (15C) are compliant (fundamental / out-of-band). Finally the integrator has to apply the appropriate equipment authorization (e.g. Verification) for the new host device per definition in $15.101. Integrator is reminded to assure that these installation instructions will not be made available to the end-user of the final host device. The final host device, into which this RF Module is integrated" has to be labeled with an auxiliary label stating the FCC ID of the RF Module, such as "Contains FCC ID: 2APNFWAC000005 Module statement The single-modular transmitter is a self-contained, physically delineated, component for which compliance can be demonstrated independent of the host operating conditions, and which complies with all eight requirements of S 15.212(a)(1) as summarized below. 1) The radio elements have the radio frequency circuitry shielded. 2) The module has buffered modulation/data inputs to ensure that the device will complywith Part 15 requirements with any type of input signal. 3) The module contains power supply regulation on the module. 4) EUT has two antennas: one is a PCB antenna, which is non removable; Another type is the rod antenna, which does not use standard antenna sockets or electrical connectors to replace the antenna 5) The module demonstrates compliance in a stand-alone configuration. 6) The module is labeled with its permanently affixed FCC lD label. 7) The module complies with all specific rules applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. 8) The module complies with RF exposure requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.Microsoft Word 2010