User Guide for Becker models including: SC211a Centronic Plus Motor, SC211a, Centronic Plus Motor, Plus Motor, Motor

[PDF] becker centronic plus motor, adding centronic sun,wind sensor or motionhelioscreen.com.au › 2024/09 › 6.-...

• Google Docs
• Google Drive
• Download [pdf]
• Download Optimized



File Info : application/pdf, 2 Pages, 807.22KB

Document Document

BECKER CENTRONIC PLUS MOTOR, ADDING CENTRONIC SUN,WIND SENSOR OR MOTION SENSOR TO AN EXISTING INSTALLATION & SETTING PROTECTION LEVELS FLOWCHART PAGE 1 BCPFC 006-1
START: USE A SWC PLUS REMOTE ALREADY PROGRAMMED IN THE CURRENT NETWORK
CAUTION! MOTOR LIMITS MUST ALREADY BE PROGRAMMED BEFORE PROCEEDING
PRESS AND HOLD PROGRAM BUTTON (1) ON THE BACK OF THE REMOTE FOR 3 SECONDS. THIS PROMPTS THE TRANSMITTER TO SEARCH FOR ALL MOTORS AND SENSORS IN THE SAME NETWORK. DURING SEARCH LED RING
WILL CONTINUALLY CHANGE COLOUR (2). THE CLOSEST MOTOR TO THE
TRANSMITTER WILL MAKE 1 X JOG THEN LED RING WILL TURN GREEN (3)
1

USING THE UP AN DOWN BUTTONS SELECT THE MOTOR THAT YOU WANT
TO PROGRAM THE CENTRONIC SENSOR TO. AS YOU CYCLE
THROUGH THE MOTORS, EACH MOTOR WILL MAKE 1 X JOG. STOP CYCLING ON THE DESIRED MOTOR
AFTER MOTOR MAKES 1 X JOG.
2

MOTION SENSOR SC211a

TO ENTER SETTING MODE, BRIEFLY PRESS AND RELEASE THE PROGRAM BUTTON(5) ON THE BACK OF THE REMOTE. LED RING WILL PULSE IN AND OUT LIGHT
BLUE (6)
3

240V WIND SENSOR SC711a, SUN & WIND

OR

SENOR SC811a. SOLAR POWERED SUN &

WIND SENSOR SC861a

PRESS THE RED PROGRAM

BUTTON (7) ON THE MOTION

SENSOR UNTIL MOTOR MAKES 1 X Click.

7

4

PRESS THE YELLOW PROGRAM BUTTON (7) ON THE SENSOR UNTIL MOTOR MAKES 1 X Click.
4a

AGAIN PRESS THE RED

PROGRAM BUTTON (8) ON THE

MOTION SENSOR UNTIL

MOTOR MAKES 2 X Click.

8

AGAIN PRESS THE YELLOW PROGRAM BUTTON (8) ON THE SENSOR UNTIL MOTOR MAKES
2 X Click.

5
BACK CONTROL
BUTTON 9

5b

CHECK OPERATION BY BRIEFLY PRESSING THE BLACK CONTROL BUTTON (9) ON THE SENSOR. MOTOR SHOULD OPERATE VAI THIS BUTTON IN THE
6 FOLLOWING SEQENCE (RETRACT/EXTEND-STOP-EXTEND/RETRACT-STOP)

AFTER CHECKING OPERATION VIA BLACK

CONTROL BUTTON. EXIT SETTING MODE

1104

BY PRESSING AND HOLDING THE

PROGRAMMING BUTTON (10) ON THE BACK

OF THE REMOTE FOR 3 SECONDS UNTIL

THE LED RING LIGHT GOES OUT

END

BECKER AUSTRALIA TECHNICAL SUPPORT 1300 813 322

7

8

9

BACK CONTROL BUTTON

BECKER CENTRONIC PLUS MOTOR, ADDING CENTRONIC SUN,WIND SENSOR OR MOTION SENSOR TO AN EXISTING INSTALLATION & SETTING PROTECTION LEVELS FLOWCHART PAGE 2 BCPFC 006-2
START: USE A SWC PLUS REMOTE ALREADY PROGRAMMED IN THE CURRENT NETWORK
CAUTION! MOTOR LIMITS MUST ALREADY BE PROGRAMMED BEFORE PROCEEDING
PRESS AND HOLD PROGRAM BUTTON (1) ON THE BACK OF THE REMOTE FOR 3 SECONDS. THIS PROMPTS THE TRANSMITTER TO SEARCH FOR ALL MOTORS AND SENSORS IN THE SAME NETWORK. DURING SEARCH LED RING
WILL CONTINUALLY CHANGE COLOUR (2). THE CLOSEST MOTOR TO THE
TRANSMITTER WILL MAKE 1 X JOG THEN LED RING WILL TURN GREEN (3)
1
USING THE UP AN DOWN BUTTONS SELECT THE MOTOR THAT YOU WANT TO SET THE PROTECTION LEVELS ON.
AS YOU CYCLE THROUGH THE MOTORS, EACH MOTOR WILL MAKE 1
X JOG. STOP CYCLING ON THE DESIRED MOTOR AFTER MOTOR
MAKES 1 X JOG.
2

ENTER SETTING MODE BY PRESSING BRIEFLY THE PROGRAM
BUTTON ON THE BACK OF THE REMOTE (5) LED RING WILL PULSE
IN AND OUT LIGHT BLUE (6)
3

TO ENTER PROTECTION LEVEL ADJUSTMENT. PRESS AND HOLD

THE FUNCTION BUTTON (7) FOR APPROX. 3 SECONDS UNTIL LED

RING CHANGES TO YELLOW. THIS NOW SHOWS THE (SUN LEVEL).TO ADJUST LEVELS, USE THE UP BUTTON TO INCREASE

8

AND DOWN BUTTON TO DECREASE (8). TO MOVE TO WIND LEVEL

PRESS & RELEASE FUNCTION BUTTON BRIEFLY (9), THE LED RING

WILL TURN RED (WIND LEVEL). TO MOVE TO RAIN FUNCTION

PRESS AND RELEASE THE FUNCTION BUTTON BRIEFLY (10). THE

LED RING WILL TURN BLUE. SEE TABLES BELOW FOR THRESHOLD

4

LEVELS AND ADJUSTMENT.

WHEN ALL LEVELS HAVE BEEN SET. EXIT BY PRESSING AND HOLDING THE

1114

PROGRAMMING BUTTON (11) FOR 3

SECONDS UNTIL THE LED RING LIGHT

GOES OUT. MOTOR MAKES

END

7

9

10

BECKER AUSTRALIA TECHNICAL SUPPORT 1300 813 322