Home | Locking solutions | DOM Security
Instructions for DOM Security models including: Tronic Mifare Electronic Lock, Electronic Lock, Tronic Mifare, Lock
File Info : application/pdf, 11 Pages, 1.63MB
DocumentDocumentTronic Mifare Instructions Tronic Mifare INSTRUCTIONS MANAGEMENT CARD MASTER CARDS USER CARDS Cards and functions MANAGEMENT CARD Function: Create and Delete Master Cards MASTER CARD Functions: Create / Delete User Cards (Single user only), Inspection mode and Delete User Cards USER CARD Functions: Open / Close locks SETTINGS CARD Transfer settings from software to locks Modes : Multiuser (Public) / Single User (Private) Acoustic signal Automatic opening time Tronic Mifare INSTRUCTIONS Single user: Open and close SINGLE USER The lock is closed. Place the assigned User Card close to the lock. The lock will open. After 2 seconds the latch closes automatically. OK: Green LED 1 long beep = the lock is closed NOT OK: Red LED and 3 short beeps. Create and delete User Cards (only for single user mode) CREATE: Place the assigned Master Card close to the lock, followed by the new User Card. Up to 50 User Cards can be created per lock. Green LED and long beep = User Card created successfully. Red LED and 3 short beeps = User Card not created. DELETE: Place the Master Card close to the lock, followed by the User Card. Green LED 2 fast blinks and 2 short beeps = User Card deleted. Multiuser: Open and close MULTIUSER The locker is open. Place a blank User Card close to the lock. The lock is now assigned to the card. If you present your card again the lock will open and reset for the next usage. (Same or different User card) OK: Green LED 1 long beep = the lock will close NOT OK: Red LED and 3 short beeps = lock is already assigned to another User Card or the User Card is already assigned to another locker. Tronic Mifare INSTRUCTIONS Create and delete Master Cards CREATE: Place the Management Card close to the lock, followed by the new Master Card. Up to 5 Master Cards can be created per lock. Green LED and long beep = Master Card created successfully. Red LED and 3 short beeps = Master Card not created. DELETE: Place the Management Card close to the lock, followed by the Master card. Green LED 2 fast blinks and 2 short beeps = Master Card deleted. Open using Master Card: Inspection mode INSPECTION MODE Place the Master Card close to the lock (1 time) Green LED and long beep Lock opens after 30 seconds After inspection time, the lock closes automatically (User Card is not deleted in Multiuser Mode) Delete all User Cards x 4 Reset User Cards Place the Master Card close to the lock (4 times) All User Cards for this lock have now been deleted. x 5 Place the Master Card close to the lock (5 times), followed by the User Card to be deleted. 1 long beep = User Card deleted. This card is now available for a new user. Tronic Mifare INSTRUCTIONS Programmable settings (management software and cable required) AUTOMATIC OPENING TIME: The lock will open automatically at the programmed time: hh : mm Mon, Tue, Wed, Thu, Fri, Sat, Sun Working days Two options: 1. Leave door open 2. Close door again ACOUSTIC SIGNAL VOLUME: High/Low/Off LED INDICATION OF CLOSED POSITION: On/Off blinking red LED when locker is closed CODES: User / Master LAST EVENTS BATTERY LEVEL NUMBER OF OPERATIONS Settings Card 7 1. Load settings from the computer to the settings card (WHITE). 2. Place the Settings card close to the lock. 3. The settings will be automatically transfered to the lock. Table Reader/Writer Used to read or write information from cards and bracelets. In conjuntion with the software, the Table Reader is an essential accessory for complete management of RFID installations. Use of the Table Reader allows remote management functions (i.e. from a reception desk) such as: Create and delete master/user cards Read relevant information from the card (locker Nr., user ID, battery level). Assign users to locks, limited time of use (hours/days/months). Read last events of the locks. Read all settings from locks. Create Settings Card to modify lock parameters. Tronic Mifare INSTRUCTIONS Batteries replacement 2 1 3 1. Connect the battery pack. 2. Loosen the Torx 20 screw. 3. Remove the battery holder. IMPORTANT: Battery replacement must completed in less than 5 minutes. The battery pack must remain connected during the release of the batteries (otherwise, the clock will lose the programmed time). 19,4 Measurements 13,3 94 61 110 40 85,7 94 114 62 4,2 44,2 9,5 18,2 25,46 IP (keypad / lock case) ----/45 Working temperature -5ºC <> +70ºC Latch force > 45Kgf UV Rays > 10000h Vibration 10 - 200 Hz 2g Life cycles > 200000 cycles Electrostatic discharge 8000 V Battery life > 35000 cycles or 2 years 2,1 Tronic Mifare WARRANTY AND WARNINGS Warranty and liability Copyright Our General Terms and Conditions apply. We do not accept liability for personal injury or property damage resulting from one or more of the following: Improper use of the furniture lock Failure to observe the notices in these instructions Incorrect assembly Incorrect product repairs Disasters caused by external influences and force majeure. This documentation may not be reproduced either in whole or in part, stored or transmitted, disclosed or translated in any form or by any means without the prior written consent of DOM Security. This documentation is updated at regular intervals. The publisher is always grateful to receive information about any errors or suggestions regarding this documentation. © DOM Security, 20, rue de l'Arc de Triomphe, 75017 Paris, France Documentation Officer DOM Security Product Management Department 20, rue de l'Arc de Triomphe 75017 Paris, France Information available online You can download these instructions and other information about the Tronic family on the product details page at www.dom-security.com