Mike Yeadon: Final Warning
varisciteportal.axosoft.com/login
DART-MX93 - Variscite Wiki
One moment, please...One moment, please...One moment, please...
User Guide for Variscite models including: DART-MX93, DART-MX93 Evaluation Kit, DART-MX93, Evaluation Kit, Kit
DART-MX93 based on NXP i.MX93 Evaluation Kit Quick Start Guide
DART-MX93 : NXP i.MX93 System on Module (SoM) / Computer on Module
File Info : application/pdf, 2 Pages, 405.79KB
DocumentDocumentDART-MX93 based on NXP i.MX93 Evaluation Kit Quick Start Guide 12 13 14 16 18 19 20 15 17 21 11 22 10 23 24 245 26 9 27 28 29 8 7 6 5 4 3 2 1 Features 1. 5V PWR IN (J4) 2. Gigabit Ethernet #1 (J5) 3. USB 3.0 OTG (J6) 4. Gigabit Ethernet #2 (J43) 5. Dual USB 3.0 Host (J7) 6. FAN 5V (J24) 7. micro SD Card slot (J9) 8. USB Debug (J10) 9. RTC BAT. Slot (JBT1) 10. Single MIPI-CSI (J11) 11. Mini PCIe #1 (J23) 12. UART, I2C (J12) 13. SAI2, SAI5, PDM, CAN (J13) 14. GPIO, SPDIF (J14) 15. QSPI (J41) 16. LVDS CH0 (J15) 17. LVDS CH1 (J26) 18. ECSPI, Host wake (J16) 19. Resistive Touch (J17) 20. Capacitive Touch (J18) 21. HDMI(J19) 22. User Buttons (SW1-SW4) 23. SAI1 (J25) 24. Reset Button (SW5) 25. ON/OFF Button (SW6) 26. Line In (J21) 27. Boot Select Switch (SW7) 28. Headphones (J22) 29. Power ON (SW8) Evaluation kit initial Setup 1. Carefully remove the 7" LCD and VAR-DT8MCustomBoard from the package. 2. Connect the 7" LCD Display and Touch cables to the Evaluation Kit connectors J15, J18 respectively. Note:connect the display cable with the red wire on pin 1. Connect the touch cable with the metal contacts facing down. 3. Plug the USB type A to micro B cable between the USB debug connector (J10) and a PC USB port. 4. For heatsink assembly instructions, please follow the VHP-DT8MM/P documentation. Please note that the heatsink is mainly used for CPU/GPU intensive applications and may be required per your specific use case. DART-MX93 based on NXP i.MX93 Evaluation Kit Quick Start Guide Setting the host PC for debug 1. Download any PC terminal software (e.g. Putty). 2. Set the PC terminal software parameters as follows: - Baud Rate: 115200 - Data bits: 8 - Stop bits: 1 - Parity: None - Flow Control: None Booting from eMMC 1. For internal boot: Set the Boot select switch (SW7) to INT position to boot from the SOM's internal storage. 2. Plug the wall adapter into the 5V power jack (J4) and to a 120VAC~240VAC power source. 3. Set Power ON switch (SW8) to ON state. 4. Boot messages should be printed within the PC terminal window. Booting from a micro SD card The microSD card is supplied within the package. Updated SD card images can also be downloaded from the Variscite FTP server. See more details in the recovery SD card section in the Variscite wiki pages. (Re-)Installing the file system on the eMMC Please refer to the recovery SD card section in the Variscite wiki pages. Links o Wiki page: https://variwiki.com/index.php?title=DARTMX93 o DART-MX93 Evaluation kits: https://www.variscite.com/product/evaluationkits/dart-mx93 -evaluation-kits/ o DART-MX93 System on Module: https://www.variscite.com/product/system-onmodule-som/cortex-a55/dart-mx93-nxp-i-mx93/ o VAR-DT8CustomBoard carrier board: https://www.variscite.com/product/single-boardcomputers/var-dt8mcustomboard o Customer portal: https://varisciteportal.axosoft.com/login 1. Set Power ON (SW4) to off state. 2. Set Boot select switch (SW7) to EXT side in order to boot from the SD card. 3. Push microSD card into the microSD card slot (J9) of the VAR-DT8MCustomBoard. 4. Set Power ON switch (SW8) to ON state. 5. Boot messages should be printed within the PC terminal window. Thank you for purchasing Variscite's product. For additional assistance please contact: sales@variscite.com P/N VSS0199