SNAPTAIN SP330 Interactive Mini Drone User Manual
VISION BEYOND IMAGINATION
Disclaimer and Safety Guidelines
CAUTION: Dispose of drone in accordance with local regulations. DO NOT treat the product as household waste.
DO NOT fly above or near obstacles, crowds, open water, public road, high voltage power lines or trees.
DO NOT use the drone in severe weather conditions. These include wind, snow, rain, smog, hail, lightning, tornadoes or hurricanes.
Avoid strong light when flying the drone.
Stay away from the rotating propellers and motors to avoid some tiny objects (e.g. hair) to get into them.
Be sure to observe all local regulations, obtain appropriate authorizations and understand risks. Please note it is solely your responsibility to comply with all flight regulations.
Maintenance and Care
- Thoroughly check the drone after a crash or violent impact.
- Store the drone in a cool, dry place away from direct sunlight.
- Do not place any heavy objects on the drone.
- Do not try to disassemble or repair the product by yourself. Please contact SNAPTAIN for more help.
Packing List
- SP330 Drone
- Water-Shaped Remote
- USB Cable
- Spare Propeller (A x2, B x2)
- Screwdriver
- Screw x4
- User Manual
Product Overview
SP330 Drone
Diagram of the SP330 Drone showing:
- Battery Compartment
- Motor
- Infrared Sensor (on both sides)
- Charging Port
- On/Off switch
- Propeller
- LED Indicator
Flight Operation Guide
Charge the Drone Before Flying
Diagram illustrating drone charging: A USB cable is connected to a power source (5V/1-2A) and the drone's charging port. A red LED indicates charging, and a green LED indicates fully charged.
Notes:
- Please use the original USB cable provided.
- The LED indicator will flash red quickly when the battery of the drone is low.
Power On and Take Off
Power On
Press and hold the On/Off button for 2 seconds. The LED indicator starts flashing red, blue, and green alternatively. Place the drone on flat ground and wait until the LED indicator turns solid green. The drone is turned on successfully.
Take Off
Option 1: Press the Waterdrop-Shaped Remote to take off. The drone will ascend.
Option 2: Place the drone in your palm, then gently throw it into the air. Please make sure there is enough space while throwing the drone up. If the LED indicator flashes red quickly, please give up throwing and charge the drone timely.
After taking off, the drone will keep rotating slowly so that the infrared sensors can detect the surroundings. The drone will fly in the opposite direction when it detects an obstacle.
Flight Directions
Ascend
Put your hand or an object under the drone. It will ascend to a certain height and make a hovering flight.
Descend
When the drone flies over a height of 1 meter, it will automatically and slowly descend to around 1 meter, then make a hovering flight.
Leftward
Put your hand or an object on the right side of the drone. It will fly leftward.
Rightward
Put your hand or an object on the left side of the drone. It will fly rightward.
Notes:
- Please make sure your hand approaches the infrared sensor of the drone.
- Strong light, black objects, and glasses will affect the flight. Please keep them away from the drone when flying.
360° Flip
Step 1: Approach two hands to the infrared sensor on each side of the drone to activate the 360° Flip function. The LED indicator starts to flash green quickly.
Step 2: Put one hand under the drone and it will flip.
This function cannot be activated when the battery of the drone is low. If the LED indicator flashes red twice when putting your hand under the drone, the 360° Flip function cannot be performed.
Circle Fly
Step 1: Approach two hands to the infrared sensor on each side of the drone to activate the Circle Fly function. The LED indicator starts to flash green quickly.
Step 2: Put one hand on the right or left side of the drone and make sure your hand approaches the infrared sensor. The drone will fly clockwise in one circle.
This function cannot be activated when the battery of the drone is low.
Speed Switch, Landing, and Stop
Speed Switch
The speed of the drone is set as LOW by default and the LED Indicator is solid green. To switch to HIGH Speed, please land the drone first, then press the On/Off button once. A solid blue LED indicator stands for the successful set. Repeat this procedure to get back to low speed.
Landing
Press the Waterdrop-Shaped Remote again during the flight to land the drone.
Stop
Grab the drone during flight and turn it over to stop flying.
Power Off and Calibration
Power Off
Press and hold the On/Off button for 2 seconds to turn off the drone.
Calibrate (Optional)
- If the flight is abnormal and the LED indicator flashes red, blue, and green alternatively after a crash, please land the drone and place it on flat ground, then wait until the LED indicator turns solid green. The drone will automatically finish the calibration. It is safe to fly the drone then.
- If the flight is abnormal after a crash, please land the drone, then quickly press the On/Off button for three times. The LED indicator will flash red, blue, and green alternatively. Next, place the drone on flat ground and wait until the LED indicator turns solid green. The calibration is complete.
Specifications
| Feature | Details |
|---|---|
| Moto | 615 Coreless |
| Drone Battery | Li-ion Battery |
| Flight Time | 5-7 mins |
| Charging Time | 30 mins |
Regulatory Information
IC STATEMENT
This device complies with RSS247 of Industry Canada. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Son fonctionnement est sujet aux deux conditions suivantes: ① le dispositif ne doit pas produire de brouillage prejudiciable, et ② ce dispositif doit accepter tout brouillage recu, y compris un brouillage susceptible de provoquer un fonctionnement indesirable.
The device must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
The symbol indicates DC voltage [DC voltage symbol].
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
Contact Information
US: support@snaptain.com
CA: support@snaptain.com
UK: support.uk@snaptain.com
DE: support.de@snaptain.com
FR: support.fr@snaptain.com
IT: support.it@snaptain.com
ES: support.es@snaptain.com
JP: support.jp@snaptain.com
