Quick Start Guide

Updating

*Do not disconnect the scanner from the computer or power off the computer during the process of updating.

*No Registration Required / PC: Windows 7, Windows 8 and Windows 10 supported.

Diagram showing the FOXWELL NT200E scanner connected via a USB cable to a computer keyboard.

1. Download the update tool NT_WONDER and install it.
2. Enable NT_WONDER and connect the NT200E/NT200C to the computer with a USB cable.
3. Click <Update online> or <Update offline> to start updating according to the software version conditions.
4. An Update Finished Message displays when the update is completed.

Device Overview

Diagram of the FOXWELL NT200E device with labeled components:

• A. OBD II Cable: Provides communication for the vehicle DLC.
• B. LCD Display: Shows menus, test results and operation tips.
• C. UP Key: Moves selection up.
• D. ESC Key: Returns to the previous screen or level.
• E. ENTER Key: Confirms an action or enters the system setup menu from the home screen.
• F. DOWN Key: Moves selection down.
• G. USB Port: Provides a USB connection for the PC or laptop.

Applicable Functions

• Read Codes / Freeze Frame Data
• Erase Codes / Live Data
• I/M Readiness / O2 Sensor Test
• On-board Monitor Test / Component Test
• Vehicle Information / Modules Present
• Unit of measure / DTC GUIDE

How to Use NT200E/NT200C?

Before start diagnosis, please make sure:

1. The ignition switch is turned to ON position.
2. The engine is off.
3. The vehicle battery voltage is between 10-14 volts.
4. The scanner is connected to the vehicle correctly.

Do not connect or disconnect the equipment while the ignition is on or the engine is running.

Diagram illustrating the location of the vehicle's OBD interface port, with an arrow indicating where to insert the scanner's OBD II connector.

1. Turn on the ignition of your car.
2. In the main menu, select "OBDII/EOBD", then the NT200E/NT200C starts scanning. Wait for several seconds, choose "yes/no" with the right arrow key, and enter the Diagnostic Menu.
3. Select "Read Codes" - Choose each selection to check. Pending Codes means the codes need to be confirmed after several driving cycles.
4. Enter "Live Data", graphing selected live data will also help locate bad sensors.
5. Enter "View Freeze Frame", which is a snapshot of critical vehicle operating conditions automatically recorded by the on-board computer at the time DTC (Diagnostic Trouble Code) set. Check the data which you need to locate bad sensors.
6. "02 Monitor Test", "On-Board Monitor Test", "Component Test", the availability of these tests may depend on the actual condition of your vehicle.
7. Enter "I/M Readiness".

OBD-II Connector and Pinout

Diagram of the OBD-II connector and pinout, detailing the function of each pin from 1 to 16:

1. Pin 1: Vendor Option
2. Pin 2: SAE J1850BUS+
3. Pin 3: Vendor Option
4. Pin 4: Chassis Ground
5. Pin 5: Signal Ground
6. Pin 6: CAN High (ISO 15765-4)
7. Pin 7: K-line of ISO 9141-2 and ISO 14230-4
8. Pin 8: Vendor Option
9. Pin 9: Vendor Option
10. Pin 10: SAE J1850BUS-
11. Pin 11: Vendor Option
12. Pin 12: Vendor Option
13. Pin 13: Vendor Option
14. Pin 14: CAN Low (ISO 15765-4)
15. Pin 15: L-line of ISO 9141-2 and ISO 14230-4
16. Pin 16: Battery Power

OBD Service Modes

• Mode 1: Real-time data, MIL, IM monitors.
• Mode 2: Freeze frame.
• Mode 3: Stored DTCs.
• Mode 4: Clear/Reset DTCs and emissions-related diagnostic information.
• Mode 5: O2 monitoring tests, supported.
• Mode 6: Test results for continuously and non-continuously monitored systems, supported.
• Mode 7: Pending DTCs.
• Mode 8: Request control of on-board-system, test or component (bidirectional controls).
• Mode 9: Request VIN and other data.
• Mode 10: Allows a scan tool to obtain permanent codes.

Contact Us

For service and support, please contact us.

Website: www.foxwelltech.us

E-mail: support@foxwelltech.com

Service Number: +86-755-26697229

Fax: +86-755-26897226

Shenzhen Foxwell Technology Co., Ltd.

Pictures illustrated here are for reference only and this Quick Start Guide is subject to change without prior notice. For more details, please refer to the User's Manual.