GTW-800-BLACK Light Strip User Manual

SAFETY WARNINGS AND GUIDELINES

Thank you for choosing Shenzhen HuaRong Yao Technology Co.,Ltd. Before using your new product, please read these instructions to prevent any damage.

When using electrical products, basic precautions should always be followed.

WARNING: These products may represent a possible shock or fire hazard if improperly installed or attached in any way.

Products should be installed in accordance with this install guide and current electrical codes.

WARNING:

• Risk of electric shock
• Do not use product where directly exposed to water.
• This product is not a toy.
• Only use the power supply applied; using a different one can damage the product.
• For safety reasons, do not break down this product, and use only in the manner intended by the manufacturer.

DO NOT roll up when using. Please spread out the LED Strip Light before connecting to power supply.

PRODUCT INSTRUCTIONS

Components:

• Strip Light
• Power Cable
• Controller

Specifications:

• Interface: USB
• Color: RGB
• Self adhesive: yes
• Input voltage: 5V DC 1A
• Wireless Control Distance: 10M (No occlusion)

Manufacturer Address: 2nd Floor, Building C, Sanmin Industrial Park, Shuitian Community, Shiyan Sub-district, Bao 'an District, Shenzhen City

PRE-INSTALLING

• Measure to the desired length before installation.
• Cut to length at scissor marks on Strip Light (ensure the power supply is not plugged in at the wall outlet).
• Clean the area thoroughly (surface must be free of dust, dirt or grease).
• Avoid bending the strip light at a sharp angle (90° Max) which may damage the LEDs.
• Avoid removing and relaying the Strip Light multiple times as the adhesive may wear off.

Installation Steps:

1. Clean the installation surface. Make sure the surface is smooth, dry, and clean.
2. Tear off the plastic on the adhesive tape and stick the strip on the desired surface.
3. Stick to the installation surface.
4. Plug into the socket. Use the RF Remote to turn on and operate the lights.

RF Remote Control Manual

• LED Color Buttons (12 Colors): Static Red / Static Green / Static Blue / Static Pink / Static Yellow / Static Orange / Static Light Orange / Static Light Blue / Static Dark Blue / Static Purple / Static Onion green / Static Grass Green
• Dynamic Mode: Dynamic lighting will perfectly customise different styles of scene effects for you.
• Speed change: Adjust the speed of dynamic modes.
• Brightness: Adjust the brightness of the lights.
• Power: Turn on/off the lights.
• Auto mode: Cycles through various modes automatically.

Light Strip APP Control Manual

The light strip can be controlled through the LYNCK APP. Scan the QR code to get the APP.

How to use the Control APP:

1. Get the Control APP: Scan the APP QR code to download and install the LYNCK APP.
2. Instructions for adding a device:
   • Turn on Bluetooth functionality on your phone.
   • Turn on the LYNCK Bluetooth device you want to connect to.
   • Click the "Add Device" or "+" button in the APP.
3. APP Features:
   • Brightness: Adjust brightness from 0% to 100%.
   • Dynamic Mode: Select from various dynamic lighting effects like Gradient color, Strobe mode, Jump mode, Colored Scene, colorful Rhythm, Music lights.
   • Speed change: Adjust the speed of dynamic modes.
   • Countdown task: Set timers for the lights.
   • Music Sync: Sync lights with music playing on your phone (requires phone radio access and sensitivity adjustment).

FCC Compliance Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.