Product Overview
This manual provides detailed information for Sleipner control panels, including installation, operation, and technical specifications. The following models are covered:
- 8950 G - Touchpanel, 12/24V
- 8955 G - Touchpanel, Rundt 12/24 Volt
- 8960 G - Joystickpanel 8960 G
- 8960 S - Joystickpanel 8960 Black
- 8965 - Boatswitchpanel, Round 12/24 V
- 8940 G - Joystickpanel Dobbelt
- 8940 S - Joystickpanel Dobbel Black
- 8909C - Docking Control Sleipner Std.
Installation Considerations and Precautions
Responsibility of Installer: The installer must read this document to ensure necessary familiarity with the product before installation. Instructions in this document cannot be guaranteed to comply with all international and national regulations. It is the responsibility of the installer to follow all applicable international and national regulations when installing Sleipner products.
Recommendations are guidelines only. Sleipner recommends obtaining advice from a person familiar with the particular vessel and applicable regulations.
This document contains general installation instructions intended to support experienced installers. For assistance, contact a professional installer.
If required by local regulation, electrical work must be done by a licensed professional.
Health and safety procedures must be followed during installation.
Faulty installation of Sleipner products will render all warranties given by Sleipner Motor AS.
Important Notes:
- These panels will only work with Side-Power thrusters with a built-in electronic control box and a 4/5 lead control cable system.
- Display area is waterproof when installed correctly. Never submerge the entire control panel unit in water as this will damage the product and cause a short-circuit.
Measurements
Detailed measurements for various control panel models are provided in tables and diagrams.
Models 8950, 8960, 8955, 8965
| Measurement Code | Measurement Description | *8950 (mm) | *8960 (mm) | *8955 (mm) | *8965 (mm) | ||||
|---|---|---|---|---|---|---|---|---|---|
| ID | Internal panel diameter cut out | 51.8 | 2 | 51.8 | 2 | 51.8 | 2 | 51.8 | 2 |
| D | Panel diameter | 86 | 3.39 | 86 | 3.39 | 86 | 3.39 | 86 | 3.39 |
| H | Panel Height | 71 | 2.8 | 71 | 2.8 | 71 | 2.8 | 71 | 2.8 |
| W | Panel width | 71 | 2.8 | 71 | 2.8 | 71 | 2.8 | 71 | 2.8 |
| (a) | Raised height above the dashboard | 7 | 0.26 | 75.3 | 2.96 | 10.7 | 0.42 | 25.21 | 1 |
| (b) | Depth behind the dashboard (not inc. cables) | 41 | 1.61 | 41.4 | 1.63 | 39 | 1.5 | 39 | 1.5 |
| (c) | Panel screw hole diameter | 3 | 0.12 | 3 | 0.12 | 2.5 | 0.10 | 2.5 | 0.10 |
| (d) | Distance between panel screw holes | 61 | 2.4 | 61 | 2.4 | 53 | 2.09 | 53 | 2.09 |
Diagrams: Visual representations of joystick control panels (8960, 8965) and their dimensions (H, W, D, cut-out ID) are provided.
Models 8940, 8909C
| Measurement Code | Measurement Description | *8940 (mm) | *8909C (mm) | ||
|---|---|---|---|---|---|
| ID | Internal panel diameter cut out | 52 | 2.05 | 52 | 2.05 |
| H | Panel Height | 121.6 | 4.79 | 121.2 | 4.79 |
| W | Panel width | 71.6 | 2.8 | 72 | 2.8 |
| (a) | Raised height above the dashboard | 82.4 | 3.2 | 28.56 | 1.12 |
| (b) | Depth behind the dashboard (not inc. cables) | 41.5 | 1.63 | 41.5 | 1.63 |
| (c) | Panel screw hole diameter | 2.5 | 0.10 | 2.5 | 0.10 |
| (d) | Distance between panel screw holes | 111.1 | 4.37 | 111.1 | 4.37 |
| (e) | Distance between panel screw holes | 61.1 | 2.4 | 61.1 | 2.4 |
Diagrams: Visual representations of joystick control panels (8940, 8909C) and their dimensions (H, W, D, cut-out ID) are provided.
Control Panel Descriptions
Control Panel 8950
Features 'Port' and 'Starboard' side thrust engagement. Double 'ON' buttons activate control, 'OFF' button deactivates. Includes LED indicator.
Control Panel 8960
Features 'Port' and 'Starboard' side thrust engagement. Double 'ON' buttons activate control, 'OFF' button deactivates. Includes LED indicator.
Control Panel 8955
Features 'Port' and 'Starboard' side thrust engagement. Double 'ON' buttons activate control, 'OFF' button deactivates. Includes LED indicator.
Control Panel 8965
Features 'Port' and 'Starboard' side thrust engagement. Double 'ON' buttons activate control, 'OFF' button deactivates. Includes LED indicator.
Control Panel 8940
Joystick control for 'Port' and 'Starboard' bow and stern thrust. Double 'ON' buttons activate control, 'OFF' button deactivates. Includes LED indicator.
Control Panel 8909C
Joystick control for 'Port' and 'Starboard' bow and stern thrust. Double 'ON' buttons activate control, 'OFF' button deactivates. Includes LED indicator.
Control Panel Installation
General Steps:
- Use the supplied cut-out template to mark the area to remove on your control dash.
- Cut out the area per template for the control panel. If the front surface around the cut-out is jagged or chipped, use a sealant to assist the gasket.
- Place the gasket to the back face of the panel.
- Plug cables into the connectors at the rear of the control panel.
- Insert the control panel in place and fasten screws.
- Insert the control panel's covering caps.
Diagrams: Visual aids show the installation process with components like covering caps, gasket, screws, and cables for different panel types.
Visual Wiring Diagram
Wiring diagrams are provided for systems with an automatic main switch and with a manual main switch. These diagrams illustrate the connections for bow and stern thrusters, control panels, Y-connectors, fuses, and switches.
Important Notes on Wiring:
- Check that there is no electrical connection between the electro motor body and the positive terminal, and between the electro motor body and the negative terminal on the motor. Contact skilled personnel for guidance if unsure.
- Common negative MUST be wired when using control panel 8940 and 8909C if separate battery banks are installed (Bow and Stern thrusters combined).
- To define appropriate (-) cable and fuse size, contact a skilled electrician.
Service and Support
Find your local professional dealer for expert service and support. Visit www.sleipnergroup.com/support.
For additional supporting documentation, visit www.sleipnergroup.com and find your Sleipner product.
Warranty Statement
Sleipner Motor AS warrants equipment against defects in workmanship and materials for two years (Leisure Use) or one year (Commercial Use) from the date of purchase.
Warranty Exclusions: The warranty does not apply to defects or damages caused by:
- Faulty installation or hook-up
- Abuse or misuse of the equipment
- Exposure to excessive heat, salt or fresh water spray, or water immersion (unless specifically designed as waterproof)
Making a Claim:
- Contact the dealer or service center where purchased, or find one at www.sleipnergroup.com.
- Provide a detailed written statement of the defect, product identification, serial number, date and place of purchase, and installer's name and address. Proof of purchase is required.
- Make the equipment available for troubleshooting and repair at the Warrantor's or an authorized service representative's premises.
Warranty Service:
- If the defect is due to faulty material or workmanship, the equipment will be repaired or replaced at Sleipner's option at no charge.
- No refund will be granted unless Sleipner is unable to remedy the defect after reasonable attempts.
- Warranty service must be performed only by Sleipner or an authorized service representative. Any attempt to remedy the defect by anyone else voids the warranty.
Limitations of Liability: Sleipner Motor AS is not responsible for injury to persons, damage to property, loss of income or profit, or any other incidental, consequential, or resulting damage or cost claimed to have been incurred through the use or sale of the equipment, including any failure or malfunction or damages arising from collision.
This warranty provides specific legal rights, and other rights may vary by country.
Patents
Sleipner continually reinvests in developing new technology. Visit www.sleipnergroup.com/patents to see patented designs.
Company Information
SLEIPNER AS
P.O. Box 519
N-1612 Fredrikstad
Norway
Copyright Sleipner Motor AS, 2021. Information was correct at publication, but Sleipner Motor AS cannot accept liability for inaccuracies or omissions. Continuous product improvement may change specifications without notice.
Patents - Sleipner Group
