Instruction Manual for DAUDIN models including: GFGW-RM01N HMI Modbus TCP Connection, GFGW-RM01N, HMI Modbus TCP Connection, Modbus TCP Connection, TCP Connection, Connection
I. The gateway is used externally to connect with Beijer HMI's communication port (Modbus TCP). II. The main controller is in charge of the management and ...
File Info : application/pdf, 13 Pages, 1.54MB
DocumentDocument2302EN V2.0.0 and Beijer HMI Modbus TCP Connection Operating Manual Table of Contents 1. Remote I/O Module Configuration List............................................................................... 3 1.1 Product Description.............................................................................................................. 3 2. Gateway Parameter Settings ................................................................................................ 4 2.1 i-Designer Program Setup .................................................................................................... 4 3. Beijer HMI Connection Setup.............................................................................................. 9 3.1 Beijer HMI Hardware Connection ....................................................................................... 9 3.2 Beijer HMI IP Address and Connection Setup .................................................................. 10 2 1. Remote I/O Module Configuration List Part No. Specification GFGW-RM01N Modbus TCP-to-Modbus RTU/ASCII, 4 Ports GFMS-RM01S Master Modbus RTU, 1 Port GFDI-RM01N Digital Input 16 Channel GFDO-RM01N Digital Output 16 Channel / 0.5A GFPS-0202 Power 24V / 48W GFPS-0303 Power 5V / 20W Description Gateway Main Controller Digital Input Digital Output Power Supply Power Supply 1.1 Product Description I. The gateway is used externally to connect with Beijer HMI's communication port (Modbus TCP) II. The main controller is in charge of the management and dynamic configuration of I/O parameters and so on. III. The power module is standard for remote I/Os and users can choose the model or brand of power module they prefer. 3 2. Gateway Parameter Settings This section details how to connect to Beijer HMI. For detailed information, please refer to the iO-GRID M Series Product Manual 2.1 i-Designer Program Setup I. Make sure that the module is powered and connected to the gateway module using an Ethernet cable II. Click to launch the software 4 III. Select "M Series Module Configuration" IV. Click on the "Setting Module" icon 5 V. Enter the "Setting Module" page for M-series VI. Select the mode type based on the connected module 6 VII. Click on "Connect" VIII. Gateway Module IP Settings Note: The IP address must be in the same domain as the controller equipment 7 IX. Gateway Module Operational Modes Note: Set Group 1 as Slave and set the gateway to use the first set of RS485 port to connect to the main controller (GFMS-RM01N) 8 3. Beijer HMI Connection Setup This chapter explains how to use the iX Developer program to connect Beijer HMI to the gateway and add a remote I/O. For detailed information, please refer to iX Developer User Manual 3.1 Beijer HMI Hardware Connection I. The connection port is on the right at the bottom of the machine. There are LAN A and LAN B II. Connect the port at the bottom of the machine to the gateway's port 9 3.2 Beijer HMI IP Address and Connection Setup I. Once HMI is powered, press on the HMI screen to enter the service menu and then click on "IP Settings". II. Click on "Specify an IP Address" and set "IP Address" to the same domain as the gateway domain at 192.168.1.XXX. 10 III. Launch iX Developer and select "MODICON" and "Modbus Master" to add a new controller IV. Click on the "Controller" tab to enter the controller setup page. Select the controller and then click on "Settings" 11 V. Connection method setup From the "Communication mode" drop-down menu, select "Ethernet TCP/ IP" Setup the default station number From the "Modbus protocol" drop-down menu, select "RTU" From the "32-bit World mapping" drop-down menu, select "Little-endian" From the "Force function code 0x10" drop-down menu, select "Enable" From the "String swap" drop-down menu, select "Disable" 12 VI. Click on "Stations" and set the "Station" and "IP Address" the same as the gateway VII. Click on "Tab" to enter the tab setting page. Next, click on "New" and set up the tab register's location iO-GRID M 's first GFDI-RM01N has the initial address at 44096 iO-GRID M 's first GFDO-RM01N has the initial address at 48192 13