peplink PEPWAVE P1MT01 Router Instructions

Instructions for peplink models including: P1MT01, U8G-P1MT01, U8GP1MT01, PEPWAVE Router, PEPWAVE P1MT01 Router, PEPWAVE P1MT01, PEPWAVE, P1MT01, P1MT01 Router, Router

User Manual-3

PISMO LABS TECHNOLOGY LIMITED P1MT01 peplink PEPWAVE Wireless Product U8G-P1MT01 U8GP1MT01 p1mt01

PISMO LABS TECHNOLOGY LIMITED P1MT01 U8G-P1MT01 U8GP1MT01 p1mt01

File Info : application/pdf, 123 Pages, 4.19MB

GetApplicationAttachment.html?id=6191155

1. Go to Network (Top tab), then Network Settings (Left-side tab), and click on Untagged LAN. This will open up the LAN settings page. 2. Change the IP address to 192.168.50.2. 3. In the DHCP Server section, uncheck the checkbox to disable DHCP Server. 4. Click Save and Apply Changes.
Step 2. Ethernet port configuration
The Ethernet port must be set to ACCESS mode for each HD Dome. To do this, dummy VLANs need to be created first.
1. Go to Network (Top tab), then Network Settings (Left-side tab), and click on New LAN. This will open the settings page to create a dummy VLAN.
2. The image below shows the values that need to be changed to create a new VLAN:

Note: set different IP addresses for each HD dome (e.g. 192.168.10.1 and 192.168.10.2).
3. Click Save and Apply Changes. 4. Go to Network (Top tab), then Port Settings (Left-side tab). 5. Set the Port Type to Access and set VLAN to Untagged LAN (see picture below).

https://www.peplink.com

251

6. Click Save and Apply Changes.
Configuration requirements for the main Router
Requirements for the main router are: - Configure WAN 1 as a DHCP client. - WAN 1 will automatically get the Gateway IP address from HD Dome 1. - Configure WAN 2 as a Static IP and set it to 192.168.50.12. - Configure WAN 2 Gateway to 192.168.50.2. Same as the HD Dome 2's IP address.

https://www.peplink.com

252

Scenario 3: SIM Injector in LAN of main Router and multiple Cellular Routers
Setup topology

In this scenario, SIMs are provided to the HD Domes via the main router. In this example, the Remote SIM Proxy functionality needs to be enabled on the main router.
Notes: - HD Dome can be replaced with any other cellular router that supports RemoteSIM. - It is recommended to use Peplink Balance series or X series routers as the main router.

https://www.peplink.com

253

This scenario requires the completion of the configuration steps for the cellular router and the SIM Injector as in Scenario 1. The configuration for the main router is explained below.
Main Router configuration
IMPORTANT: Main router LAN side and Cellular Routers must be configured using different subnets, e.g. 192.168.50.1/24 and 192.168.100.1/24. Note: please make sure the Peplink router is running Firmware 8.1.0 or above. 1. Open the main router WEB interface and change: From <IP address>/cgi-bin/MANGA/index.cgi to <IP address>/cgi-bin/MANGA/support.cgi. This will open the support.cgi page.
2. Scroll down to find Remote SIM Proxy and click on [click to configure] that is located next to it. 3. Check the Enable checkbox. 4. Click on Save. 5. Go back to the index.cgi page and click on Apply Changes.

https://www.peplink.com

254

Scenario 4: SIM Injector in a remote location
Setup topology

Requirements for installing a SIM Injector in a remote location: Cellular router communicates with the SIM Injector via UDP port 50000. Therefore this port must be reachable via public IP over the Internet. The one way latency between the cellular router and the SIM Injector should be up to 250 ms. A higher latency may lead to stability issues. The cellular router must have Internet connection to connect to the SIM Injector. It can be another Internet connection via Ethernet or Fiber if possible, or a secondary cellular interface with a local SIM (Ignite SIM). Due to its high latency, it is not recommended to use satellite WAN for connecting to a SIM Injector in remote locations.
SIM Injector configuration is the same as in Scenario 1.
Cellular Router configuration
Step 1. Enable the SIM Injector communication protocol.
1a. For a Balance cellular router, go to the Network (Top tab). 1b. For a MAX cellular router, go to the Advanced (Top tab).

https://www.peplink.com

255

2. Under Misc. settings (Left-side tab), find Remote SIM Management. 3. In Remote SIM Management, click on the edit icon next to Remote SIM is Disabled. 4. Enter the public IP of the SIM Injector and click Save and Apply Changes.
Notes: - Do NOT check Auto LAN Discovery. - Do NOT add a SIM Injector serial number to the Remote SIM Host field.
Step 2. RemoteSIM and custom SIM card settings configurations are the same as in Scenario 1.

https://www.peplink.com

256

How to check if a Pepwave Cellular Router supports Remote SIM
1. Go to Network (Top tab), then WAN (Left-side tab), and click Details on any cellular WAN. This will open the WAN Connection Settings page. 2. Scroll down to Cellular settings. If you can see the Remote SIM Settings section, then the cellular router supports Remote SIMs.
Monitor the status of the Remote SIM
1. Go to Network (Top tab), then WAN (Left-side tab), and click Details on the cellular WAN which was configured to use RemoteSIM. 2. Check the WAN Connection Status section. Within the cell WAN details, there is a section for Remote SIM (SIM card IMSI, SIM Injector serial number and SIM slot).

https://www.peplink.com

257

Appendix C: Overview of ports used by Peplink SD-WAN routers and other Peplink services

Default Port Number

Usage

Service

UDP 5246

Data flow

InControl

TCP 443

HTTPS service

InControl

TCP 5246

Optional, used when TCP

443 is not responding

InControl

TCP 5246

Remote Web Admin

InControl Virtual Appliance

TCP 4500

VPN Data (TCP Mode)

PepVPN / SpeedFusion

TCP 32015

VPN handshake

PepVPN / SpeedFusion

UDP 4500

VPN Data

PepVPN / SpeedFusion

UDP 32015º

VPN Data (alternative)

PepVPN / SpeedFusion

TCP/UDP 4500+N-1^

VPN Sub-Tunnels Data

PepVPN / SpeedFusion

UDP 32015+N-1^

VPN Sub-Tunnels Data (alternative)

PepVPN / SpeedFusion

UDP 4500

VPN Data

IPsec

UDP 500

VPN initiation

IPsec

UDP 500

L2TP

Remote User Access

UDP 1701

L2TP

Remote User Access

UDP 4500

L2TP

Remote User Access

UDP 1194

OpenVPN

Remote User Access

IP 47

PPTP (GRE)

Remote User Access

TCP 2222

Peplink

Remote Assistance Direct Troubleshooting

connection

Assistance

TCP 80

HTTP traffic

Web Admin

Inbound/Outbound Outbound Outbound

Default Status Enabled
Enabled

Outbound

Enabled

Outbound Inbound / Outbound*

Enabled Disabled

Inbound / Outbound* Disabled Inbound / Outbound* Disabled

Inbound / Outbound*
Inbound / Outbound* Inbound / Outbound*

Disabled
Disabled Disabled

Inbound

Disabled

Inbound

Disabled

Inbound

Disabled

Inbound

Disabled

Inbound

Disabled

Outbound Inbound

Enabled Enabled

https://www.peplink.com

258

TCP 443 TCP 8822 UDP 161 UDP 162 TCP, UDP 1812 TCP, UDP 1813
UDP 123
TCP 60660

HTTPS traffic SSH SNMP Get SNMP Trap Radius Authentication Radius Accounting

Interface access Web Admin Interface access (secure) SSH SNMP monitoring SNMP monitoring Radius Radius

Network Time Protocol NTP

Real-time location data in

NMEA format

GPS

Inbound Inbound Inbound Outbound Outbound Outbound Inbound Outbound
Outbound

Enabled Disabled Disabled Disabled Disabled Disabled Disabled Enabled
Disabled

Disclaimer:
By default, only TCP 32015 and UDP 4500 are needed for PepVPN / SpeedFusion. Inbound / Outbound* - Inbound = For Server mode; Outbound = For Client mode UDP 32015º - If IPsec VPN or L2TP/IPsec RUA is enabled, the UDP 4500 is occupied, so
PepVPN / SpeedFusion will automatically switch to UPD 32015 as VPN data port . UDP 32015+N-1^ / TCP/UDP 4500+N-1^ - When using Sub-Tunnels, multiple ports are in use (1
for each Sub-Tunnel profile). The default UDP data ports used when using (N number of Sub-Tunnel profiles) are:
4500...4500+N-1, or (when port 4500 is in use by IPsec or L2TP/IPsec) 32015... 32015+N-1".

https://www.peplink.com

259

Appendix D: Declaration
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice:
For MAX BR1 Mini
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11.
FCC Radiation Exposure Statement (for MAX BR1 mini)
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

https://www.peplink.com

260

CE Statement for Pepwave Routers ( MAX BR1 Mini for EC25-E)

https://www.peplink.com

261

https://www.peplink.com

262

2.4GHz ( 2412 2472 MHz ) : 16.38 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )
This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/

https://www.peplink.com

263

CE Statement for Pepwave Routers ( MAX BR1 Mini for MC7455)

https://www.peplink.com

264

https://www.peplink.com

265

2.4GHz ( 2412 2472 MHz ) : 16.38 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )

This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
contact as: https://www.peplink.com/

https://www.peplink.com

266

Industry Canada Statement (for MAX BR1 Mini)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement économique Canada.
This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body.
Cet équipement est conforme avec l'exposition aux radiations ISED définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimum de 20 cm entre le radiateur et votre corps.

https://www.peplink.com

267

FCC & IC Requirements for Operation in the United States and Canada (for MAX BR1 Mini)
FCC ID : U8G-P1930LITER6
FCC 15.21: The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
RF exposure warning: This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
IC Warning: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions
1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause
undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes
1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioelect rique subi, meme si le
brouillage est susceptible d'en compromettre le fonctionnement.

https://www.peplink.com

268

Informations concernant l'exposition aux frequences radio (RF) Cet equipement est conforme avec l'exposition aux radiations IC definies pour un environnement noncontrole. Cet equipement doit etre installe et utilise a une distance minimum de 20 cm entre le radiateuret votre corps. Cet emetteur ne doit pas etre co-localisees ou operant en conjonction avec une autreantenne ou transmetteur.
Les utilisateurs finaux et les installateurs doivent etre informes des instructions d'installation de l'antenne et des conditions de fonctionnement de l'emetteur afin de satisfaire a la conformite d'exposition RF.
This radio transmitter IC 20682-P1930LITER6 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Le present emetteur radio 20682-P1930LITER6 a ete approuve par Innovation, Sciences et Developpement economique Canada pour fonctionner avec les types d'antenne enumeres ci dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est superieur au gain maximal indique pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'emetteur.
antenna type Omni-directional antenna gain 5.33

https://www.peplink.com

269

FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice:
For MAX BR1 MK2
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 24cm between the radiator & your body.
Industry Canada Statement (For MAX BR1 MK2)
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement économique Canada.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio

https://www.peplink.com

270

exempts de licence. L'exploitation est autorisee aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en
(i) The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and The high-power radars are allocated as primary users (i.e. priority users) of the band 5725-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
(i) Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour l'exploitation point à point et non point à point, selon le cas.
En outre, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bande 5725-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Radiation Exposure Statement
This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body.
Cet équipement est conforme avec l'exposition aux radiations ISED définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimum de 20 cm entre le radiateur et votre corps.

https://www.peplink.com

271

CE Statement for Pepwave Routers ( MAX BR1 MK2 )

https://www.peplink.com

272

https://www.peplink.com

273

2.4GHz ( 2412 2472 MHz ) : 19.95 dBm 5GHz ( 5150 - 5250 MHz ) : 22.73 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )

https://www.peplink.com

274

FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice:
For MAX BR1 Classic
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
FCC Radiation Exposure Statement (for MAX BR1 Classic )
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

https://www.peplink.com

275

Industry Canada Statement ( for MAX BR1 Classic )
This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions (1) This device may not cause interference; and(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.
This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body.
Cet équipement est conforme avec l'exposition aux radiations ISED définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimum de 20 cm entre le radiateur et votre corps.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement économique Canada.

https://www.peplink.com

276

CE Statement for Pepwave Routers ( MAX BR1 Classic for MC7455)

https://www.peplink.com

277

https://www.peplink.com

278

2.4GHz ( 2412 2472 MHz ) : 19.78 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )
This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/

https://www.peplink.com

279

CE Statement for Pepwave Routers ( MAX BR1 Classic for EC25-E)

https://www.peplink.com

280

https://www.peplink.com

281

https://www.peplink.com

282

FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice:
For MAX HD4 MBX, MAX HD2 MBX, MAX HD4 MBX 5G, MAX HD2 MBX 5G
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
IMPORTANT NOTE
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
ISED Warning Statement For MAX HD4 MBX
Industry Canada Statement
This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions (1) This device may not cause interference; and(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.

https://www.peplink.com

283

Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement économique Canada.
(i) The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and The high-power radars are allocated as primary users (i.e. priority users) of the band 5725-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
(i) Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour l'exploitation point à point et non point à point, selon le cas. En outre, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bande 5725-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
IC Radiation Exposure Statement
This equipment complies with Innovation, Science and Economic Development Canada RF exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated to ensure a minimum of 20 cm spacing to any person at all times.
Declaration d'exposition aux radiations Cet equipement est conforme aux limites d'exposition aux rayonnements IC etablies pour un environnement non controle. Cet equipement doit etre installe et utilise avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
This radio transmitter 20682-P1MBX has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
WIFI Antenna type Replacement Antenna WIFI Antenna gain 2.4GHz / 2.44 dBi , 5GH / 4.73 dBi LTE Antenna type Replacement Antenna LTE Antenna gain 4.38 dBi

https://www.peplink.com

284

Battery Caution Statement (MAX HD4 MBX, MAX HD2 MBX, MAX HD4 MBX 5G, MAX HD2 MBX 5G)
Risk of explosion if the battery is replaced by an incorrect type.

https://www.peplink.com

285

CE Statement for Pepwave Routers ( MAX HD4 MBX For EM7565 )

https://www.peplink.com

286

https://www.peplink.com

287

2.4GHz ( 2412 2472 MHz ) : 19.6 dBm 5GHz ( 5150 - 5250 MHz ) : 19.4 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )

https://www.peplink.com

288

CE Statement for Pepwave Routers ( MAX HD2 MBX / MAX HD4 MBX For LM960A18)

https://www.peplink.com

289

https://www.peplink.com

290

2.4GHz ( 2412 2472 MHz ) : 19.6 dBm 5GHz ( 5150 - 5250 MHz ) : 19.4 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )
This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
contact as: https://www.peplink.com/

https://www.peplink.com

291

CE Statement for Pepwave Routers (MAX HD2 MBX 5G / MAX HD4 MBX 5G For MV31-W)

https://www.peplink.com

292

https://www.peplink.com

293

2.4GHz ( 2412 2472 MHz ) : 19.6 dBm 5GHz ( 5150 - 5250 MHz ) : 19.4 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )

https://www.peplink.com

294

FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice:
For MAX HD2
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 50 centimeters between the radiator and your body.
Industry Canada Statement (MAX HD2)
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement économique Canada.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en

https://www.peplink.com

295

(i) The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and The high-power radars are allocated as primary users (i.e. priority users) of the band 5725-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
(i) Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour l'exploitation point à point et non point à point, selon le cas. En outre, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bande 5725-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Radiation Exposure Statement
This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 37cm between the radiator & your body. 70 cm minimum distance for the device operate with plug-in USB cellular device which has maximum of 7W(ERP) output power.
Cet équipement est conforme avec l'exposition aux radiations ISED définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimum de 37 cm entre le radiateur et votre corps. Distance minimale de 70 cm pour que l'appareil fonctionne avec un appareil cellulaire USB enfichable qui a une puissance de sortie maximale de 7 W (ERP).
Battery Caution Statement
Risk of explosion if the battery is replaced by an incorrect type.

https://www.peplink.com

296

https://www.peplink.com

297

CE Statement for Pepwave Routers ( MAX HD2 For MC7455)

https://www.peplink.com

298

https://www.peplink.com

299

2.4GHz ( 2412 2472 MHz ) : 19.90 dBm 5GHz ( 5150 - 5250 MHz ) : 22.88 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )

https://www.peplink.com

300

CE Statement for Pepwave Routers ( MAX HD2 For MC7565)

https://www.peplink.com

301

https://www.peplink.com

302

2.4GHz ( 2412 2472 MHz ) : 19.86 dBm 5GHz ( 5150 - 5250 MHz ) : 22.68 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )
This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/

https://www.peplink.com

303

( For MAX BR1 Classic CB IEC 62368-1 )
Mounting the Unit
Wall Mount
The Pepwave MAX BR1 Classic can be wall mounted using screws. After adding the screw on the wall, slide the MAX in the screw hole socket as indicated below. Recommended screw specification M3.5 x 20mm, head diameter 6mm, head thickness 2.4mm.
The Pepwave MAX BR1 Classic requires four screws for wall mounting.

Output of the external power source shall complied with ES1 and ES2 requirements, output rating 10-30 Vdc, minimum 12W ( DC Jack or POE injector ), with minimum ambient temperature 65 , altitude = 5000m , and evaluated in accordance to UL/EN/IEC 60950-1 and / or UL/EN/IEC 62368-1
Ensure to connect the power cord of power adapter to a socket-outlet with earthing

https://www.peplink.com

304

FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice:
For MAX BR1 Pro 5G
FCC 15.21 The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 23 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

https://www.peplink.com

305

Industry Canada Statement ( MAX BR1 Pro 5G )
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en
compromettre le fonctionnement.Informations concernant l'exposition aux frequences radio (RF)
Cet equipement est conforme avec l'exposition aux radiations IC definies pour un environnement noncontrole.
Cet equipement doit etre installe et utilise a une distance minimum de 23 cm entre le radiateuret votre corps.
Cet emetteur ne doit pas etre co-localisees ou operant en conjonction avec une autreantenne ou transmetteur.
Les utilisateurs finaux et les installateurs doivent etre informes des instructions d'installation de l'antenne et des
conditions de fonctionnement de l'emetteur afin de satisfaire a la conformite d'exposition RF.
This radio transmitter IC 20682-P1AX02 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
antenna type Omni-directional
antenna gain for 2.4GHz 2.44 dBi

https://www.peplink.com

306

antenna gain for 5GHz ( 5150 ~ 5250 MHz ) 4.10 dBi antenna gain for 5GHz ( 5725 ~ 5850 MHz ) 4.73 dBi
Battery Caution Statement Risk of explosion if the battery is replaced by an incorrect type.

https://www.peplink.com

307

CE Statement for Pepwave Routers ( MAX BR1 Pro 5G)

https://www.peplink.com

308

https://www.peplink.com

309

2.4GHz ( 2412 2472 MHz ) : 19.74 dBm 5GHz ( 5150 - 5250 MHz ) : 22.66 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )

https://www.peplink.com

310

FCC Requirements for Operation in the United States
Federal Communications Commission (FCC) Compliance Notice:
For MAX BR1 Mini Core
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Industry Canada Statement ( MAX BR1 Mini Core )
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Le present produit est conforme aux specifications techniques applicables a l'innovation, Science et Developpement economique Canada.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

https://www.peplink.com

311

Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en
Radiation Exposure Statement
This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body.
Cet équipement est conforme avec l'exposition aux radiations ISED définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimum de 20 cm entre le radiateur et votre corps.

https://www.peplink.com

312

FCC Requirements for Operation in the United States
Federal Communications Commission (FCC) Compliance Notice:
For MAX 700
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 22 centimeters between the radiator and your body.

https://www.peplink.com

313

For MAX HD2 IP67, MAX HD2 Mini, MAX HD2 Dome, MAX HD4 IP67, MAX
BR1 ENT, MAX BR1 M2M, SpeedFusion Engine
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Industry Canada Statement (MAX HD2 IP67, MAX HD2 Mini, MAX HD2 Dome, MAX HD4 IP67, MAX BR1 ENT, MAX BR1 M2M, SpeedFusion Engine)
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Le present produit est conforme aux specifications techniques applicables d'Innovation, Sciences et Developpement economique Canada.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

https://www.peplink.com

314

https://www.peplink.com

315

CE Statement for Pepwave Routers ( MAX HD2 IP67 )

https://www.peplink.com

316

https://www.peplink.com

317

WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )
This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/

https://www.peplink.com

318

CE Statement for Pepwave Routers ( MAX HD1 Dome )

https://www.peplink.com

319

https://www.peplink.com

320

https://www.peplink.com

321

CE Statement for Pepwave Routers ( MAX HD2 Dome )

https://www.peplink.com

322

https://www.peplink.com

323

https://www.peplink.com

324

CE Statement for Pepwave Routers ( MAX BR1 ESN )

https://www.peplink.com

325

https://www.peplink.com

326

2.4GHz ( 2412 - 2472 MHz ) : 19.78 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )
This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/

https://www.peplink.com

327

FCC Requirements for Operation in the United States
Federal Communications Commission (FCC) Compliance Notice:
For MAX HD4
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 40 centimeters between the radiator and your body.
Industry Canada Statement (MAX HD4)
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Le present produit est conforme aux specifications techniques applicables d'Innovation, Sciences et Developpement economique Canada.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired opera- tion of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio ex- empts de licence. L'exploitation est autorisee aux deux conditions suivantes

https://www.peplink.com

328

(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en
(i) The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and
The high-power radars are allocated as primary users (i.e. priority users) of the band 5725-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
(i) Le dispositif fonctionnant dans la bande 5150-5250 MHz est reserve uniquement pour une utilisation a l'interieur afin de reduire les risques de brouillage prejudiciable aux systemes de satellites mobiles utilisant les memes canaux;
(ii) Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer a la limitation P.I.R.E specifiee pour l'exploitation point a point et non point a point, selon le cas.
En outre, les utilisateurs devraient aussi etre avises que les utilisateurs de radars de haute puissance sont designes utilisateurs principaux (c.-a-d., qu'ils ont la priorite) pour les bande 5725-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Radiation Exposure Statement
This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 40cm between the radiator & your body.
Cet equipement est conforme avec l'exposition aux radiations ISED definies pour un environnement non controle. Cet equipement doit etre installe et utilise a une distance minimum de 40 cm entre le radiateur et votre corps.

https://www.peplink.com

329

CE Statement for Pepwave Routers ( MAX HD4 )

https://www.peplink.com

330

https://www.peplink.com

331

2.4GHz ( 2412 - 2472 MHz ) : 18.87 dBm 5GHz ( 5150 - 5250 MHz & 5725 - 5850 MHz ) : 19.13 dBm
WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )

https://www.peplink.com

332

CE Statement for Pepwave Routers ( MAX HD4 IP67 )

https://www.peplink.com

333

https://www.peplink.com

334

WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )

https://www.peplink.com

335

CE Statement for Pepwave Routers ( SpeedFusion Engine )

https://www.peplink.com

336

https://www.peplink.com

337

WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) MC7455 module:

EC25-E module:

https://www.peplink.com

338

FCC Requirements for Operation in the United States
Federal Communications Commission (FCC) Compliance Notice:
For MAX Transit, MAX Transit Duo
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 24 centimeters between the radiator and your body.
Industry Canada Statement (MAX Transit, MAX Transit Duo)
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Le present produit est conforme aux specifications techniques applicables d'Innovation, Sciences et
Développement économique Canada.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired opera- tion of the device.

https://www.peplink.com

339

Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio ex- empts de licence. L'exploitation est autorisee aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en
(i) The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and
The high-power radars are allocated as primary users (i.e. priority users) of the band 5725-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
(i) Le dispositif fonctionnant dans la bande 5150-5250 MHz est reserve uniquement pour une utilisation a l'interieur afin de reduire les risques de brouillage prejudiciable aux systemes de satellites mobiles utilisant les memes canaux;
(ii) Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer a la limitation P.I.R.E specifiee pour l'exploitation point a point et non point a point, selon le cas.
En outre, les utilisateurs devraient aussi etre avises que les utilisateurs de radars de haute puissance sont designes utilisateurs principaux (c.-a-d., qu'ils ont la priorite) pour les bande 5725-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Radiation Exposure Statement
This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 30cm between the radiator & your body.
Cet equipement est conforme avec l'exposition aux radiations ISED definies pour un environnement non controle. Cet equipement doit etre installe et utilise a une distance minimum de 30 cm entre le radiateur et votre corps.
Battery Caution Statement
Risk of explosion if the battery is replaced by an incorrect type.
CE Statement for Pepwave Routers ( MAX Transit / MAX Transit Duo For EM7565 )

https://www.peplink.com

340

https://www.peplink.com

341

https://www.peplink.com

342

2.4GHz ( 2412 - 2472 MHz ) : 18.68 dBm 5GHz ( 5150 - 5250 MHz ) : 18.19 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )
This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
contact as: https://www.peplink.com/

https://www.peplink.com

343

CE Statement for Pepwave Routers ( MAX Transit For LM960A18 )

FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice:
For MAX Transit Mini
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Industry Canada Statement (MAX Transit Mini)
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Ce produit répond aux spécifications techniques applicables à l'innovation, Science et Développement économique Canada.
Radiation Exposure Statement
This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body.
Cet équipement est conforme avec l'exposition aux radiations ISED définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimum de 20 cm entre le radiateur et votre corps.

This radio transmitter has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Antenna types Replacement Antenna Antenna gain (in dBi) 5.33 dBi
Innovation, Sciences et Developpement economique Canada a approuve l'utilisation de ce transmetteur radio avec les types d'antenne enumeres ci-dessous, le gain maximal admissible etant indique. Les types d'antennes non inclus dans cette liste qui ont un gain superieur au gain maximal indique pour tout type liste sont strictement interdits pour une utilisation avec cet appareil.
Types d'antennes Replacement Antenna Gain d'antenne (en dBi) 5.33 dBi

CE Statement for Pepwave Routers ( MAX Transit Mini )

2.4GHz ( 2412 - 2472 MHz ) : 19.78 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )
This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator & your body. contact as: https://www.peplink.com/

FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice:
For MAX BR1 PRO, MAX BR2 PRO, UBR LTE
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 23 centimeters between the radiator and your body.
Industry Canada Statement (MAX BR1 PRO, MAX BR2 PRO, UBR LTE)
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement économique Canada.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired opera- tion of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio ex- empts de licence. L'exploitation est autorisee aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en

For licence exempt equipment with detachable antennas, the user manual shall also contain the following notice in a conspicuous location:
This radio transmitter 20682-P1941 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
WIFI Antenna type: Replacement Antenna WIFI Antenna gain: 2.4GHz I 2.44 dBi , 5GHz I 4.73 dBi LTE Antenna type: Replacement Antenna (04-410055-00) LTE Antenna gain: 4 dBi LTE Antenna type: Replacement Antenna (04-410093-01) LTE Antenna gain: 4.38 dBi
(i) The device for operation in the band 51505250 MHz is only for indoor use to reduce the potent for harmful interference to co-channel mobile satellite systems;
(ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate; (detachable antenna only) ; and The high-power radars are allocated as primary users (i.e. priority users) of the band 5725-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
(iii) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.
(i) Le dispositif fonctionnant dans la bande 5150-5250 MHz est reserve uniquement pour utilisation a l'interieur afin de reduire les risques de brouillage prejudiciable aux systemes de satellites mobiles utilisant les memes canaux;
(ii) Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour l'exploitation point à point et non point à point, selon le cas. (antenne détachable uniquement)
En outre, les utilisateurs devraient aussi etre avises que les utilisateurs de radars de haute puissance sont designes utilisateurs principaux (c.-a-d., qu'ils ont la priorite) pour les bande 5725-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
(iii) En outre, les utilisateurs devraient aussi etre avises que les utilisateurs de radars de haute puissance sont designes utilisateurs principaux (c.-a-d., qu'ils ont la priorite) pour les bande 5725-5850 MHz et

Radiation Exposure Statement
This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 23 cm between the radiator & your body.
Cet equipement est conforme avec l'exposition aux radiations ISED definies pour un environnement non controle. Cet equipement doit etre installe et utilise a une distance minimum de 23 cm entre le radiateur et votre corps.

CE Statement for Pepwave Routers ( MAX BR1 PRO / MAX BR2 PRO / UBR LTE )

2.4GHz ( 2412 - 2472 MHz ) : 19.94 dBm 5GHz ( 5150 - 5250 MHz ) : 20.34 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )
This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
contact as: https://www.peplink.com/

FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice:
For MAX BR1 IP55, MAX BR2 IP55
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

CE Statement for Pepwave Routers ( MAX BR1 IP55 )

2.4GHz ( 2412 - 2472 MHz ) : 18.16 dBm 5GHz ( 5150 - 5250 MHz) : 20.32 dBm 5GHz ( 5725 - 5850 MHz) : 13.00 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )
This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 50cm between the radiator & your body. contact as: https://www.peplink.com/

CE Statement for Pepwave Routers ( MAX BR2 IP55 )

2.4GHz ( 2412 - 2472 MHz ) : 18.99 dBm 5GHz ( 5150 - 5250 MHz ) : 22.95 dBm 5GHz ( 5725 - 5850 MHz ) : 12.80 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class )
This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 50cm between the radiator & your body. contact as: https://www.peplink.com/

FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice:
For MAX Transit Pro E / MAX Transit LTEA
FCC 15.21: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
FCC 15.105 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

ICES Statement
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement économique Canada.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisee aux deux conditions suivantes:
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en
RF exposure warning
This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Cet équipement est conforme avec l'exposition aux radiations ISED définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimum de 20 cm entre le radiateur et votre corps. Cet émetteur ne doit pas être colocalisées ou opérant en conjonction avec une autre antenne ou transmetteur.

This radio transmitter IC: 20682-P1835 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Cet émetteur radio IC : 20682-P1835 a été approuvé par Innovation, Sciences et Développement économique Canada doit fonctionner avec les types d'antennes énumérés ci-dessous, avec le gain maximal admissible indiqué. Les types d'antenne non inclus dans cette liste qui ont un gain supérieur au gain maximum indiqué pour tout type répertorié sont strictement interdits pour une utilisation avec cet appareil.

FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice:

For MAX BR1 Mini (FCC ID: U8G-P1MT01)

Federal Communication Commission Interference Statement

Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Industry Canada Statement (MAX BR1 Mini, IC: 20682-P1MT01)

This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.

Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement économique Canada.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio ex-empts de licence. L'exploitation est autorisee aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en

https://www.peplink.com

264

(i) The device for operation in the band 51505250 MHz is only for indoor use to reduce the potent for harmful interference to co-channel mobile satellite systems;
(ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate; (detachable antenna only) ; and The high-power radars are allocated as primary users (i.e. priority users) of the band 5725-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
(iii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate.
(i) Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour l'exploitation point à point et non point à point, selon le cas. En outre, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5725-5850 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
(iii) Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour l'exploitation point à point et non point à point.
Radiation Exposure Statement
This equipment complies with ISED RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
Cet appareil doit être installé et utilisé avec une distance minimale de 20cm entre l'émetteuret votre corps. Cet appareil et sa ou ses antennes ne doivent pas être co-localisés ou fonctionner en conjonction avec tout autre antenne ou transmetteur.

https://www.peplink.com

265

This radio transmitter IC: 20682-P1MT01 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
WIFI Antenna type: Omni-directional WIFI Antenna gain: 2.4GHz / 3.15 dBi 5150 ~ 5250 MHz / 3.29 dBi 5725 ~ 5850 MHz / 4.76 dBi
Cet émetteur radio IC : 20682-P1MT01 a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d'antennes répertoriés ci-dessous, avec le gain maximal autorisé indiqué. Les types d'antenne non inclus dans cette liste qui ont un gain supérieur au gain maximum indiqué pour tout type répertorié sont strictement interdits pour une utilisation avec cet appareil.
Type d'antenne WIFI : omnidirectionnelle Gain de l'antenne Wi-Fi : 2.4 GHz / 3.15 dBi 5150 ~ 5250 MHz / 3.29 dBi 5725 ~ 5850 MHz / 4.76 dBi

https://www.peplink.com

266

NCC statement
For MAX BR1 Mini (HW3)

MPE: 1 mW/cm2: 0.116 mW/cm2 20
(FDD) - WCDMA 2100 (Band 1) FDDLTE1920MHz -1980MHz \ 2110MHz -2170MHz - WCDMA 900 (Band 8) FDDLTE1885MHz -915MHz \ 930MHz -960MHz - LTE 2100 (Band 1) FDDLTE1920MHz -1980MHz \ 2110MHz -2170MHz - LTE 1800 (Band 3) FDDLTE1710MHz -1770MHz \ 1805MHz -1865MHz - LTE 2600 (Band 7) FDDLTE2500MHz2570MHz \ 2620MHz2690MHz - LTE 900 (Band 8) FDDLTE885MHz -915MHz \ 930MHz -960MHz - LTE 700 (Band 28) FDDLTE703MHz -748MHz \ 758MHz -803MHz
(TDD) - LTE 2600 (Band 38) TDD(2570MHz2620MHz) - LTE 2600 (Band 41) TDD(2500MHz2690MHz)

USB WAN Modem Port Specification MAX Series

MAX 700 Output Rating 5V DC, 2A

MAX HD2 / MAX HD2 Media Fast
5V DC, 2A

MAX HD2 Mini

MAX HD2 / HD4 MBX

MAX BR1 ENT
MAX BR1NT

MAX HD4 / MAX HD4 Media Fast /
MediaFast 200

5V DC, 2A

5V DC, 0.5A

5V DC, 2A

References

Mozilla/5.0 (Windows NT 10.0; Win64; x64) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/99.0.4844.74 Safari/537.36 Skia/PDF m99