Ansten TV headphones – Ansten TV Headphones
User Manual for ANSTEN models including: K1 Bluetooth Headphone with Bluetooth Transmitter Charging, K1, Bluetooth Headphone with Bluetooth Transmitter Charging, Bluetooth Transmitter Charging, Transmitter Charging, Charging
K1 User Manual (PDF) ANSTEN ANSTEN ANSTEN,【2023,Upgraded】,Wireless,Headphones,for,TV,Watching,with,Digital,Optical,RCA,AUX,Bluetooth,Transmitter,Charging,Dock,,Over,Ear,Headset,for,Seniors,,30,Hrs,Audio,Playtime,,Plug,n,Play,,
Amazon.com: MONODEAL Wireless Headphones for TV Watching with Digital Optical RCA AUX Bluetooth 5.1 Transmitter & Charging Dock, Over Ear Headset for Seniors, 100ft Range, 30Hrs Playtime, No Lip-Sync Delay : Electronics
Turn on the Bluetooth headphone or Bluetooth speaker, enter pairing mode, place K1 Transmitter and the device close and wait for about 30 seconds, when Blue LED ...
File Info : application/pdf, 1 Pages, 2.55MB
DocumentDocumentBluetooth Headphone with Bluetooth Transmitter Charging Base K1 User Manual Contents: 1. Product Overview ---------------------------------------------------------------------- 2 2. Basic Operation ------------------------------------------------------------------------ 4 3. Bluetooth Pairing and Connection ------------------------------------------------- 5 4. AUX Wired Connection --------------------------------------------------------------- 6 5. LED Indicator --------------------------------------------------------------------------- 7 6. Charging---------------------------------------------------------------------------------- 8 7. TTS Tone -------------------------------------------------------------------------------- 9 8. Bluetooth Transmitter Charging Base ------------------------------------------- 9 8.1 Bluetooth transmitter operation ------------------------------------------------ 9 8.2 Bluetooth Pairing and Connection -------------------------------------------- 10 8.3 Connection with Two Devices ------------------------------------------------- 11 8.4 LED Indicator ---------------------------------------------------------------------- 12 8.5 Charging ---------------------------------------------------------------------------- 13 9.Product Specification ---------------------------------------------------------------- 14 9.1 Headphone Specification ------------------------------------------------------ 14 9.2 Bluetooth Transmitter Charging Base Specification ---------------------14 10. Attention and Q & A -----------------------------------------------------------------15 -1- 1. Product Overview: Charging LED Indicator Charging Base Charging Port Power Button Microphone Micro USB Charging Port 3.5mm AUX Volume + MFB (Multi Function Button) Volume LED Indicator Power Buttont 3.5mm AUX Port Optical Input Port Micro USB Charging Port -2- LED Indicator MFB (Multi Function Button) Headphone Charging Port Package Contents: A. K1 Bluetooth Headphone x 1 B. Micro USB Charging Cable x 1 C. K1 Bluetooth Transmitter Charging Base x 1 D. User Manual x 1 E. 3.5mm AUX Cable x 1 F. Optical Cable x 1 G. RCA Cable x 1 Bluetooth Headphone with Bluetooth Transmitter Charging Base K1 User Manual D E F -3- 2. Basic Operation 3. Bluetooth Pairing and Connection 4. AUX Wired Connection 5. LED Indicator Button Power Button MFB Function Operation Power on In off status, switch to ON side to power on, it will enter pairing mode automatically Power off In on status, switch to OFF side to power off Play/pause Short press to pause / play music when playing music Redial last phone call Double press to redial the last phone call number Answer a call Hang up a call Short press when call coming Short press during a call A. Switch to ON side, the K1 will power on and enter pairing mode with Red and Blue LED flash alternately. B. Search and click to connect "K1" on your phone Bluetooth lists, LED turns to solid Blue LED after connected. C. Control to answer/hang up a call, music play/ pause, previous/ next song, volume up/ down etc through the MFB /Volume +/Volume- buttons. Plug one end of 3.5mm cable in the 3.5mm AUX interface of headphone, another end plug in phone or PC audio port. When the audio cable is plugged in using the AUX function, the headphone button has no function. The AUX function can also be used when the headphone battery has no power. Status Power on Power off Pairing Unconnected standby mode LED Indicator Blue LED is on for 2 seconds Red LED is on for 2 seconds Blue and Red LED flash alternately Blue LED flash once every 2 seconds Volume + Reject a call Volume up Next song Long press for 1 second to reject a call when call coming Short press (There is a tone when the volume is at its maximum) Long press for 1 second pairing 2 connection Connected standby mode Playing music Solid Blue LED Solid Blue LED Volume - Volume down Previous song Short press (There is a tone when the volume is at its minimum) Long press for 1 second Volume+ Voice assistant In connected standby or music status, short press Volume - & Volume + at the same time to turn on & Volume- Delete pairing record Long press Volume - & Volume + at the same time for 5 seconds Switch to ON side, K1 will power on and enter pairing mode automatically with Red and Blue LED flash a lternately. Search and connect Search and click to connect "K1" on your phone Bluetooth lists 3.5 mm AUX cable 3.5 mm AUX cable Notes: 1. The buttons of headphone are invalid when AUX mode. 2. AUX function could be work when battery out of power or item power off. Talking mode Delete paired records Charging Full charged Low battery Solid Blue LED Red and Blue LED is on for 2 seconds at the same time Solid Red LED Solid Blue LED Red LED flash once every 10 seconds 3. Bluetooth function will power off when plug AUX cable. 4. The headphone can not power on while plugged AUX cable, need to pull G out the cable first then power on the headphone. -4- -5- -6- -7- 6. Charging Please charge the K1 at once when the Red LED flash. Charging time about 2 hours. Blue LED turn on when full charged. Connection for charging 1. Plug one end of micro USB cable to K1, another end to USB charger ( Car charger, power bank or PC etc ) Micro USB charging cable Charging with Power Charging with PC 2. Use Charging Base for charging, connect Micro USB charging cable to Charging Base, place K1 Headphone on the Charging Base, Headphone's Red LED is on when is charging, Blue LED turn on when is full charged. ( When K1 transmitter is power on and use as the Charging Base for charging, place K1 Headphone on the Charging Base, the K1 transmitter will power off with Red LED flash once) Notes: 1. Please charge the item at least once for every 2 months when without use. 2. Charge when power on, it is normal for the Bluetooth indicator will overlapping with the charge indicator. -8- 7. TTS Tone Status Power on Power off Enter pairing mode Connected successful Disconnect Low voltage alert TTS Tone Power on Power off Pairing Connected Disconnected Battery low 8. Bluetooth transmitter charging base 8.1 Bluetooth transmitter operation Function Operation Power on Power off Plug in Micro USB charging cable to charging port, switch power button to ON side Switch power button to OFF side; Plug out charging cable; Put the headphone on it for charging will turn off the transmitter Enter pairing mode In unconnected standby or connected one device status, long press MFB for 5 seconds to enter paring mode. (When connected one device and enter pairing mode, the first connected device is not affected and can be used normally. Not work when in multi point connections, when the second device is connected successfully will with temporarily bad working, please wait for 5 to 20 seconds for normal working.) No connection in pairing mode, will keep pairing mode all the time Delete In pairing mode, double press MFB to clear the device information. If have no pairing record binding device record, will enter paring mode automatically, If have binding device record, will enter reconnect mode -9- Binding device operation 1. First, delete the pairing record. Double press the MFB in pairing mode ( Because there is only one pairing record to perform the binding operation). 2. Pair and connect the binding device with K1. 3. After successfully connect with the headphone, double-click the MFB to bind, and the blue LED flash 5 times after the binding is successful. 4. Replace the binding device when there is a binding record. After delete the pairing record, bind the new device to K1 Transmitter after successful connection, then the bind device record can be replaced. 5. After successfully binding the device information, K1 Transmitter automatically re-power on and reconnects to the device. Reboot can update the storage space and avoid new problems. 8.2 Bluetooth pairing and connection 1. Plug in Micro USB charging cable to charging port, switch power button to ON side to power on. 2. Enter pairing mode: Power on will enter pairing mode automatically; Unconnected standby mode or connected one device, long press MFB for 5 seconds to enter pairing mode. 3. Turn on the Bluetooth headphone or Bluetooth speaker, enter pairing mode, place K1 Transmitter and the device close and wait for about 30 seconds, when Blue LED is on after connected. 4. Connect one end of 3.5mm AUX cable with K1, another end to phone or PC, the headphone or speaker can be heard music from phone or PC. -10- 3.5 mm AUX cable 3.5 mm AUX cable *If to use optical cable connection, please plug in the Optical input port. 8.3 Connection with Two Devices 1. Follow 8.2 to connect with the first device, long press MFB button for 5 seconds to enter pairing mode (The first connected device will work well). 2. Turn on the second device (Bluetooth headphone, speaker or receiver) enter pairing mode, place it close with K1 Transmitter and wait for 30 seconds, K1 will connect the second device. After the device is connected, you can hear music from it, this is the multi point connections. (The first device will have music issue when connect to second device, then it will be fine after few seconds) *Priority support aptXTM low latency for one connection (Connected device must support aptXTM low latency), support aptXTM low latency for two connections if two devices priority support aptXTM low latency, support aptXTM for two connections if two devices priority support aptXTM, it will turn to SBC if two devices CODEC is not the same like one support aptXTM low latecy and another one support aptXTM. -11- 8.4 LED Indicator Status Power on Power off Pairing Reconnect Standby Delete pairing record Connected Multi point connections Charging Full Charged LED Indicator Without binding device, Blue LED flash twice. With binding device, Blue LED is on for 5 seconds. Red LED flash once Blue and Red LED flash alternately Blue LED flash once every second Blue LED flash once every 2 seconds Red and Blue LED is on for 2 seconds at the same time Solid Blue LED Solid Blue LED Solid Red LED Solid Green LED -12- 8.5 Charging 1. K1 Charging Base has no build-in battery, need power supply when use as bluetooth transmitter or charging for headphone. 2. Charging connection Plug one end of micro USB cable to K1 Charging Base, another end to USB charger (Car charger, power bank or PC etc ) Micro USB charging cable Charging with Power Charging with PC *1. When K1 transmitter is power on and use as the Charging Base for charging, place K1 Headphone on the Charging Base, the K1 transmitter will power off with Red LED flash once 2. Please cut off the power supply if not use. -13- 9. Product Specification 9.1 Headphone Specification: Bluetooth Version V5.0 Bluetooth Chipest QCC3034 Operation Range 10 meters Bluetooth Profile HSP, HFP, AVRCP, A2DP CODEC aptXTM Low Latency, aptXTM, AAC, SBC Battery Capacity 600mAh/3.7V Charging Time About 2 hours Standby Time Music Playing Time 80 hours About 28 hoursc70% volume Net Weight About 234g Dimension 193.3*160*80.3mm Notes: The actual using time will be different according to the ambient and music style. 9.2. Bluetooth Transmitter Charging Base Specification: Bluetooth Version V5.0 Bluetooth Chipest CSR BC8670 Operation Range Indoor barrier free 30 meters Bluetooth Profile A2DP CODEC aptXTM Low Latency, Faststream, aptXTM, SBC Net Weight About 145g Dimension 170*100*40.7mm -14- 10. Attention and Q & A About K1 Headphone: A. How to delete paired records? Power on , long press "Volume - & Volume +" buttons for 5 seconds at the same time to delete paired records ( Red and Blue LED is on for 2 seconds at the same time). Pls try to delete paired records when have connection problems. B. What's the password for pairing? Some devices require password for pairing, pls try 0000 (four zero), 8888 (four eight), 1111 (four one) or 1234 ( one two three four). C. Which devices could charge for the headphone? Any car charger, power bank, PC etc which meet DC 5V, charging current more than 400mA could be charge for this item. And K1 Charging Base. D. How to do if can not power or connection issue? Please try charging reset, when power on, plug charging cable to charge to reset and power off. (When power button switch to ON, reset will power on automatically; When power button switch to OFF, reset will not power on) Re-power on can use normally. -15- E. Why the headphone power off automatically? K1 will power off under standby mode for over 10 minutes, or the battery voltage is less than 3.1V. F. Disconnect (Out of valid connection range)? When headphone and transmitter are out of valid connection range, headphone will enter Linkloss mode (Indicator is still connected, headphone will reconnect last device every 15 seconds), will enter paring mode if reconnect fail for over 10 minutes. About K1 Bluetooth Transmitter Charging Base: A. About reconnect K1 can storage 4 devices information, and the excess will be replaced by new device information (Why store 4 units? Because K1 will reconnect to all paired devices after power on, and if there are too many, the reconnection time will be too long) K1 waiting time for re-connection is: if one device is paired, the re-connection time is about 10 seconds, and the reconnection time for two devices is 12 seconds; When there are pairing records, K1 will automatically connect to all connected devices every time when power on (but only 2 devices can be connected at the same time, and the bind device will be connected first and then to the last connected device) B. How to delete pairing record In paring mode, double press MFB to clear the device information. If have -16- no binding device record, will enter paring mode automatically, If have binding device record, will enter reconnect mode C. How to select SPDIF/AUX The default power on status is optical mode, and it will automatically switch to AUX mode when the AUX audio cable is inserted. D. How to charge for the charging base The charging base has no build-in battery, need power supply when use as bluetooth transmitter or charging for headphone. E. How to do if can not power on or dead when connect? Please try reset and power on, and delete the pairing record. Customer Service Free user support: We offer telephone, email and live online support. Your email is guaranteed to be replied to within 1 working day, and is normally responded to even faster than that! Ansten support site also provides complete step-by-step instructions and answers to FAQ online. Online Video User Guides We have clear video user guides for most of our products, which you can find on video sites. You can search on youtube: "Ansten TV headphone" Contact us: Email: anstenusa@gmail.com site: www.ansten.net -17- 110X120mm 128