Motorised Knob BMP01 User Manual

General Instructions

This manual is intended for technically qualified and trained installers. Mottura Serrature di Sicurezza S.p.A. thanks you for choosing this product and reminds you:

• To read these instructions very carefully before installing this product and before doing any maintenance.
• That all assembly and connection procedures must follow good practice procedures and comply with current laws and standards.
• To NOT install this product in explosive rooms or atmospheres or in the presence of inflammable fumes/gases.
• DO NOT install this product on a door with risk of contact with water or atmospheric agents unless the door is adequately protected.
• To switch off the power supply and disconnect all live parts before doing any installation or maintenance work on the product. Take all possible precautions to eliminate the risk of electrical shock when performing installation or maintenance procedures described in this manual.
• That the installer must deliver these instructions and all of the maintenance instructions to the user.
• To keep these instructions for future reference and attach the sales receipt to validate the warranty.
• To contact authorized dealers only in case of problems.

Mottura Serrature di Sicurezza S.p.A. may change the characteristics of the products described in these instructions at any time and without notice.

Made in Italy

Warranty Terms

This product has been inspected by Mottura Serrature di Sicurezza S.p.A. and is guaranteed to be free of all manufacturing defects for the time specified by current Italian law, starting on the date of purchase indicated on the sales receipt. The warranty is in force if the sales receipt, showing details identifying the product, is exhibited to customer service personnel. The warranty covers the replacement or repair of parts found defective at origin due to manufacturing defects. Costs of shipping to and from service centres will be paid by the customer. In case of repeated malfunctions of the same type or unrepairable defects, Mottura Serrature di Sicurezza S.p.A. may, at its own discretion, replace the entire product. The warranty on the replaced product will continue until expiration of the original warranty. If service work must be performed at the customer's premises, the customer shall – if requested – pay the authorised technical personnel travel expenses. Risks related to product transportation shall be covered by the customer when shipped directly by the customer, and by the authorised technician when the product is picked up and shipped by the technician.

Limits of Liability

The warranty does not cover damage deriving from:

• Negligence, carelessness or use in any manner not described in these instructions.
• Failure to protect the device before doing any procedure that may generate scrap or waste (welding, drilling of panels, drilling of structure, etc.) that prevents its correct functioning.
• Maintenance performed in any manner not described in these instructions or by unauthorised personnel.
• Transport without the necessary precautions and from any circumstances that cannot be attributed to manufacturing defects.

In addition, Mottura Serrature di Sicurezza S.p.A. declines all liability for any damage to persons or property deriving from failure to observe all of the precautions described herein.

Possible Installations on Cylinders with European Profile

Key / Knob Provision

Installable with bMOTO basic kit + Spacers if needed. ART. 94.431 (4pcs already included in the package).

[Diagram description: Shows a European profile cylinder with a mounting plate and the bMOTO basic kit components, indicating compatibility for key/knob provision.]

Key / Key

Installable with bMOTO basic kit + Spacers plates if needed. ART. 94.431 (4pcs already included in the package).

[Diagram description: Shows a European profile cylinder with a mounting plate and the bMOTO basic kit components, indicating compatibility for key/key provision.]

Compatible Accessories (Not included)

• bDIGIT: Keypad BLE
• bTRACK: Fingerprint reader BLE
• bTAG: Transponder reader BLE
• bKEY: Remote control BLE

Warnings

⚠️ The device contains rechargeable lithium-ion batteries (Li-ion).

The device contains a short-range radio frequency transmitter in the 2402÷2480 MHz frequency band and uses Bluetooth Low Energy (BLE) technology. Transmit power: 0dBm. Restrictions on use: None. The permitted European band is included in the ERC/REC 70-03 document as band b) of Annex 3: WIDEBAND DATA TRANSMISSION SYSTEMS. There are no restrictions for use in EU+EFTA countries for this band. Product compliant with the RED Directive 2014/53/EU.

Declaration of Conformity (DoC) available at: https://www.mottura.it/it/download/certificazioni/doc

It is recommended to carry out the installation without the batteries on board and without the mains power cable connected, since if during the installation the lock were activated, even involuntarily, by rotating it could cause serious injury to the operator! ⚠️

Power Warnings

bMOTO is powered by rechargeable batteries already included. The knob batteries absolutely CAN NOT BE tampered with in any way. In the event of malfunction or need, they can be replaced EXCLUSIVELY with those indicated in the manual (see page 10).

N.B. Correct operation of the motorised knob cannot be guaranteed if a cable and/or power supply other than those supplied are used.

Assembly Warnings

• bMOTO is to be mounted only on the internal side of the door.
• bMOTO CANNOT be installed on locks without a latch.
• bMOTO CANNOT be installed on locks with fast quick release or automatic locking.
• bMOTO CANNOT be installed on rim locks that do not have fixing holes for the Defender with 38mm centre distance.
• bMOTO must be perpendicular (90°) to the lock/door panel, and in line with the cylinder.
• For optimal installation on a Mottura rim lock, it will be necessary to remove the connector installed inside it at the entrance of the knob provision. To remove the connector, unscrew the 3 grains (via the appropriate access) that block it. Use the cover for the rotation of the shaft to identify the position of the grains.

Environmental and Battery Disposal Information

Pursuant to article 26 of Italian Legislative Decree no. 49 of 14 March 2014 “Implementation of EU Directive 2012/19 concerning waste electrical and electronic equipment (WEEE)” and article 9 of Italian Legislative Decree no. 188 of 20 November 2008 “Implementation of EC Directive 2006/66 on batteries and accumulators and waste batteries and accumulators”, adequate waste sorting for subsequent sending of disposed equipment to recycling, treatment and environmentally compatible disposal contributes to avoiding possible negative effects on the environment and human health and promotes reuse and/or recycling of the materials composing the equipment.

Unlawful disposal of the product by the user may result in the application of penalties pursuant to current laws and regulations on the matter. We remind that batteries and power adapters, if present, must be removed before the device is disposed. Batteries and adapters must be collected and separately disposed.

CE marking ℹ️

Package Contents

The package includes:

• 1x Knob body
• 1x Knob cover
• 1x Escutcheon cover
• 1x Magnetic USB-C Charging Cable
• 1x Adapter for thinner keys
• 1x Adapter for knob provision
• 4x Knob trim fixing screws
• 1x Knob cover fixing screw
• 1x Black Rubber Screw Washer
• 4x Spacers
• 1x Fixing hole template

[Diagram description: An exploded view showing all the components listed above, with corresponding numbers.]

Possibility of Installing on Different Door Types

Security Doors

[Diagram description: Illustrates installation on a security door.]

Wooden Doors

[Diagram description: Illustrates installation on a wooden door.]

Aluminium Doors

[Diagram description: Illustrates installation on an aluminium door.]

Cylinder Assembly Instructions Key / Knob Provision

(See Warnings Page 3)

1. Step 1: Measure shank length. The connector must be flush with the shank. Minimum length 8mm. Insert the connector ⑥ onto the shank, ensuring the groove faces downwards. Secure with 2 grub screws. Rotate the connector so the socket remains vertical. N.B.

   [Diagram description: Shows a cylinder shank with measurements and the connector being inserted.]

2. Step 2: Fit bMOTO onto the connector, ensuring the cut inside is vertical (see image 2A). [Image 2A description: Close-up view of the connector and bMOTO alignment.]

   [Diagram description: Shows the bMOTO unit being attached to the connector.]

3. Step 3: Measure the distance between bMOTO and the door panel. Then remove bMOTO and the connector.

   [Diagram description: Shows measurement being taken on the door panel.]

4. Step 4: N.B. The cut must be carried out with utmost precision. Transfer the measurement to the cylinder shank and make the cut. N.B.2 Using a file, create a flat surface on the shank to improve the fixing of the grain.

   [Diagram description: Shows the cylinder shank being cut and filed.]

5. Step 5: N.B. Before fastening the screws on bMOTO, check the alignment with the door panel. After making the cut, repeat operations in Figure 1 and Figure 2. Then fix bMOTO using the 4 holes on the plate (see pag.8). N.B.

   [Diagram description: Shows bMOTO being aligned and fixed with screws.]

6. Step 6: Power the knob by removing the plastic tab. Insert and secure the cover and escutcheon.

   [Diagram description: Shows the final assembly steps with cover and escutcheon.]

N.B. If the shank is shorter than 8mm, it will not be possible to install the adapter.

Fig.1: In the case of a shank without a groove, make a 4mm diameter hole into which to screw one of the connector 6 grub screws.

Fig.5: If there is a gap between the panel and the knob, compensate with spacer art.94431.

Key/Key Cylinder Assembly Instructions

1. Step 1: Cut the key 8mm from the stop. Then insert it into the cylinder and rotate it until it is in a horizontal position. N.B. Key thickness MAX 3mm.

   [Diagram description: Shows a key being cut and inserted into a cylinder.]

2. Step 2: The appropriate connector will already be inserted inside the knob. Make sure that the key cut is positioned horizontally (to facilitate insertion with the key).

   [Diagram description: Shows the connector inside the knob with the key slot.]

3. Step 3: Fit bMOTO onto the cylinder, making sure that the key fits into the groove of the connection bushing.

   [Diagram description: Shows bMOTO being attached to the cylinder with the key.]

4. Step 4: Compensate the space left between the panel and bMOTO with the shims 94.431. Once you have found the right number of spacers, fix everything using the 4 holes (see pag.8).

   [Diagram description: Shows spacers being used to fill gaps, and fixing holes.]

N.B. *In case you have a Mottura rim lock series 38.6..., you will need to use the 94.427 thickness plate as the first one to fix the cylinder.

Assembly Instructions for Rim Lock

(See Warnings Page 3)

1. Step 1: Measure the length of the shank. The shank should be between 8-10mm long. If it is longer, you will need to cut it.

   [Diagram description: Shows measurement of the cylinder shank.]

2. Step 2: Insert the connector ⑥ onto the knob provision, making sure to have the groove facing downwards and secure the 2 grub screws. Rotate the connector so that the socket remains in the vertical position. N.B. pag.5

   [Diagram description: Shows connector insertion into the rim lock provision.]

3. Step 3: Fit bMOTO onto the connector, making sure that the cut inside is in a vertical position (3A). Check the distance between the lock and the knob (3B), and compensate with the plates (not included in the package).

   [Diagram description: Shows bMOTO attached to the connector and alignment check.]

4. Step 4: Fix the necessary plates (included 4pcs) on the lock using the defender fixing screws. Fit bMOTO on the connector, making sure the groove is horizontal. Fix the escutcheon using the 4 threaded screws. (SEE WARNINGS for using plates).

   [Diagram description: Shows plates being fixed, bMOTO attached, and escutcheon secured.]

5. Step 5: Power the knob by removing the plastic tab. Insert and secure the cover and escutcheon.

   [Diagram description: Shows final steps of powering and securing covers.]

Warnings for using plates

• In case you have a Mottura lock 94.427 D/S, you will need to use the (94.427D/S) plate as the first plate for fixing the cylinder + 2x 94.431 (not included).
• In case you have a lock with front cylinder fixing, use the 3x 94.431 plates as spacers. (4pz included).

[Diagram description: Shows the 94.427 D/S and 94.431 plates.]

Template for Fixing Holes

N.B. To be able to use the drilling template, it will be necessary to have the European profile cylinder protruding from the door panel (#), otherwise it will not be possible to use the template.

Before fixing the knob to the panel, use the supplied template to make more precise pre-holes.

[Diagram description: Shows the template positioned on a cylinder. Holes F1 indicate fixing holes for the bMOTO body. Holes T1 indicate fixing holes for the 94431 thickness plates. (Ø 3mm holes F1 - T1).]

Assembly Sequence and Use of the Template for Fixing Holes

[Diagram description: Illustrates the sequence of using the template, applying bMOTO body fixing screws, plate fixing screws (not included), and spacers 94431. N.B. The template must be removed before installing the spacers.]

Knob Description

The bMOTO motorized knob is a mechatronic device designed to open/close a lock by rotating the European cylinder connected to it. The device is powered by rechargeable batteries. The device is equipped with Bluetooth Low Energy (BLE) which makes it interfaceable with a series of other peripherals of the bTECHNOLOGY Mottura line and with smartphones, following a pairing procedure via the bMOTTURA app. The cylinder can always be operated using a mechanical key (outside) or a manual knob (inside). From the inside, a simple button allows it to be opened/closed, with the possibility of activating the assisted operation mode by rotating the knob on the inside.

Key Features:

• Status LED indicator (LED Status charging)
• Open/Close Button
• RESET button
• USB-C input for battery charging with magnetic cable

[Diagram description: Top view of the knob showing labeled components. Side view showing dimensions: 68mm width, 14mm depth, 93mm height, Ø50mm cylinder diameter.]

Power Supply

(See Warnings Page 3)

bMoto is powered by rechargeable batteries (already included). To feed it, you will have to remove the tab indicated in yellow in the image. ??

Charging the Batteries (Through USB-C input)

Connect the USB power supply (supplied in the package) to the motorized knob using the USB-C cable provided. The time required to recharge the knob if the batteries are completely dead is approximately 2-3 hours. If the charging time is much longer than indicated, the batteries may be damaged. Once charging is complete, disconnect the power supply from the mains and unhook the magnetic cable. The USB-C connector can be left connected to the knob for subsequent use.

If it is necessary to replace the B-Moto batteries, it is MANDATORY to use 99.786 batteries supplied on request by Mottura Serrature di Sicurezza. The use of different batteries is dangerous for the user and may cause damage to the product. Mottura Serrature di Sicurezza will not be responsible for any damage caused by the use of batteries other than those indicated.

N.B: The correct functioning of the motorised knob cannot be guaranteed if you use a cable and/or power supply other than those supplied.

[Diagram description: Shows the USB-C charging port and the magnetic cable. Also shows battery icons.]

Rechargeable batteries: 3x Rechargeable batteries, Cod. 99.786

LED Indicators:

• LED FLASHING (Charging)
• LED FIXED (Full charge)

Knob Operation Types

Internal Operation Via Button

A short press of the main button opens the door, a long press closes it (see button table).

Bluetooth Operation

All Mottura bTECHNOLOGY Bluetooth peripherals are directly compatible with the motorized knob. It is also possible to operate the device from a smartphone.

Remote Button/Intercom Operation

Use the Bluetooth device code 99BKEY0003 by connecting a dry N.O. contact as indicated in the manual of the same.

Manual Operation

In case of emergency, the knob can be turned manually from the inside or using the key from the outside. If the batteries are low, the device can only be operated in this way to avoid damaging the batteries.

The key operation must never be performed if the “assisted rotation both PARTIAL and COMPLETE” functions are used. If the knob is used in the PARTIAL or COMPLETE assisted mode, ALWAYS remove THE KEY FROM THE CYLINDER, as the rotation of the key could cause injury to the user.

Reset Button

The RESET button is a key that, if held down for a certain time, allows you to return the knob to the factory conditions, that is, eliminating all the associations made, including the learning of the lock throws. To perform the RESET, you will need to hold down the reset button for 5 seconds until the fixed white LED lights up. Alternatively, perform the reset from the bMOTTURA application.

Available Functions

[Diagram description: Shows a flat or round-tipped tool being used to press the reset button.]

First Programming via bMOTTURA App

Device Management via bMOTTURA App

⚠️ To program and manage this device, you will need to use the bMOTTURA APP. All programming and management of Mottura bTECHNOLOGY BLE products is controlled directly via the Mottura application, with guided procedures during the various steps of programming the new devices. ACCESS CONTROL management is integrated within the App.

[Diagram description: Shows QR code for downloading the bMOTTURA app from App Store and Google Play.]

Open/Close Button

From the inside, you can open/close the lock by pressing the OPEN/CLOSE button as follows:

[Diagram description: Shows a finger pressing the internal OPEN/CLOSE button.]

Template for Plate Fixing Holes

[Diagram description: A full-scale template showing hole positions labeled F1 and T1, with a central circle indicating Ø8mm. Includes crosshairs for alignment.]

SCALA 1:1

SERIAL CODE: [Blank field]

Website: www.mottura.it