Retro High Toilet

Parts and Tools

Toilet Seat Options

• 333225HV / 333225HVM: Glossy white, with chrome/brass fittings
• 333225BS / 333225BSM: Glossy black, with chrome/brass fittings
• 333225BR / 333225BRM: Walnut, with chrome/brass fittings

Other Required Parts

• P-tube (Art. No. 329002): Not part of the delivery, must be purchased separately.
• Mounting kit for cistern (Art. No. 15525): Contains screws, washers, and plugs. Not part of the delivery, must be purchased separately.

Necessary Tools

• Pencil for marking
• Wrench / Pipe wrench
• Screwdriver
• Drill
• Sealant gun
• Allen key (for pinion screw)

Installation Instructions

Cistern Preparation and Mounting

The cistern is prepared and fitted.

Step A: Flushing Mechanism Installation

Fit the flushing mechanism into the cistern:

1. Mount the conical gasket onto the threaded part of the flushing mechanism.
2. Place the flushing mechanism into the hole in the cistern.
3. Mount the metal disk onto the threaded part of the flushing mechanism, located under the cistern.
4. Attach Screwing Part 1 to the threaded part of the flushing mechanism.

Attach the drag-and-drop weight bar to one of the side holes (optional) in the cistern. Connect it to the flushing mechanism using the supplied cord. [?]

Fit the filling unit/float (not shown in the drawing) into the opposite side hole in the cistern.

Step B: Mounting Cistern to Wall

Mount the cistern at the desired height on the wall. The maximum distance between the underside of the cistern and the center hole in the basin should be 180 cm.

• For mounting into wood: Use bolt A.
• For mounting into concrete: Use bolt B.

Bolts and plugs are not included in the delivery; mounting kit 15525 can be purchased additionally.

Step C: Flush Pipe Connection

Mount the gaskets and O-ring onto the flush pipe. Slide the pipe up, screw in Part 1, and then fasten Part 2 onto Part 1.

Step D: Traction Support

Attach the traction support to the wall and ensure the chain is vertical. [⬇️]

Step E: Flush Pipe Installation

The flush pipe is 180 cm long. If it is too long, the L-shaped part should be shortened.

Mount the pipe in the connecting pieces. Mark on the wall where to drill. Drill a Ø6 mm hole, fit the plug, and attach the wall bracket with the screw.

Mount the flush pipe in the wall brackets and tighten the pinion screw with an Allen key.

Install the white rubber gasket onto the flush pipe.

Drain Pipe and Toilet Bowl Installation

The drain pipe must be located 180 mm from the finished floor to the center of the drain. The toilet must be mounted on a flat surface.

Step A: Sliding Toilet into Drain Pipe

Slide the toilet into the drain pipe.

Step B: Securing the Toilet Bowl

1. Mark on the floor where the toilet bowl is to be mounted, using the holes on each side of the toilet bowl as guides. Remove the toilet.
2. Drill Ø8 mm holes. Seal the holes with acid-free sanitary silicone.
3. Fit plugs into the holes. Seal the plugs with acid-free sanitary silicone.
4. Refit the toilet.

Fasten the toilet to the floor using washers and screws. Fit the cover caps.

Seal the toilet bowl against the floor with acid-free sanitary silicone.

Flush the water pipe before connecting it to the cistern's water intake. [?]

Toilet Seat Installation

Note: Some of the drawings may differ from the delivered toilet seat.

1. Install the hinges in the toilet bowl.
2. Loosely tighten the screws.
3. Attach the toilet seat to the hinges.
4. Adjust the toilet seat by sliding it back and forth, and sideways, until the edge of the seat is flush with the toilet bowl.
5. Click the seat off. (Note: The clicking function may differ from what is shown in the drawing.)
6. Now, tighten the screws very firmly.
7. Install the cover caps.
8. Install the toilet seat.
9. Slide the lock over the pawl.